| B0061:11 |
Passenger Seatbelt Tension Sensor: Circuit Short to Ground |
GO to Pinpoint Test AE
. |
| B0061:12 |
Passenger Seatbelt Tension Sensor: Circuit Short to Battery |
GO to Pinpoint Test AE
. |
| B0061:13 |
Passenger Seatbelt Tension Sensor: Circuit Open |
GO to Pinpoint Test AE
. |
| B0061:1C |
Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range |
GO to Pinpoint Test AE
. |
| B00A0:54 |
Occupant Classification System: Missing Calibration |
GO to Pinpoint Test AF
. |
| B00A0:67 |
Occupant Classification System: Signal Incorrect After Event |
CARRY OUT the OCS zero seat weight test. REFER to Occupant Classification Sensor (OCS) System Zero Seat Weight Test
. |
| B00A0:76 |
Occupant Classification System: Wrong Mounting Position |
GO to Pinpoint Test AF
. |
| B00A0:97 |
Occupant Classification System: Component or System Operation Obstructed or Blocked |
GO to Pinpoint Test AG
. |
| B00C2:12 |
Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery |
GO to Pinpoint Test AH
. |
| B00C2:13 |
Passenger Seat Occupant Classification Sensor "C": Circuit Open |
GO to Pinpoint Test AH
. |
| B00C2:1A |
Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Below Threshold |
GO to Pinpoint Test AH
. |
| B00C2:49 |
Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure |
GO to Pinpoint Test AF
. |
| B00C2:81 |
Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data Received |
REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING (2 OF 2)
. |
| B00C3:12 |
Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery |
GO to Pinpoint Test AI
. |
| B00C3:13 |
Passenger Seat Occupant Classification Sensor "D": Circuit Open |
GO to Pinpoint Test AI
. |
| B00C3:1A |
Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Below Threshold |
GO to Pinpoint Test AI
. |
| B00C3:49 |
Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure |
GO to Pinpoint Test AF
. |
| B00C3:81 |
Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data Received |
REPAIR all other OCSM DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING (2 OF 2)
. |
| B1193:00 |
Crash Event Storage Full and Locked: No Sub Type Information |
INSTALL a new passenger seat track assembly (includes OCS weight sensor bolts). REFER to SEATING (2 OF 2)
. CLEAR all DTCs before carrying out the System Reset Procedure. |
| B1A59:01 |
Sensor 5 Volt Supply: General Electrical Failure |
GO to Pinpoint Test AJ
. |
| B1A59:11 |
Sensor 5 Volt Supply: Circuit Short to Ground |
GO to Pinpoint Test AJ
. |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test AK
. |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AL
. |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AM
. |
| U0401:00 |
Invalid Data Received From ECM/PCM "A": No Sub Type Information |
U0401:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT the PCM self-test. REPAIR any vehicle speed or communication-related DTCs. REFER to the DTC chart in ELECTRONIC ENGINE CONTROLS
or the ENGINE CONTROLS - POWERTRAIN DTC CHARTS & DESCRIPTIONS (EXCEPT DIESEL & HYBRID)
. |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
U0422:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:00. CARRY OUT the BCM self-test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC chart in DIAGNOSTIC TROUBLE CODE (DTC) CHART
. |
| U0422:81 |
Invalid Data Received From Body Control Module: Invalid Serial Data Received |
U0422:81 sets when the OCSM is not receiving the ignition status data that it expects from the BCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:81. CARRY OUT the BCM self-test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC chart in DIAGNOSTIC TROUBLE CODE (DTC) CHART
. |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
U0452:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:00. CARRY OUT the RCM self-test. REPAIR any SRS -related DTCs. REFER to Restraints Control Module (RCM) DTC Chart
. |
| U0452:81 |
Invalid Data Received From Restraints Control Module: Invalid Serial Data Received |
U0452:81 sets when the OCSM is not receiving the SRS data that it expects from the RCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:81. CARRY OUT the BCM self-test. REPAIR any SRS -related DTCs. REFER to Restraints Control Module (RCM) DTC Chart
. |
| U200D:12 |
Control Module Output Power A: Circuit Short To Battery |
GO to Pinpoint Test AN
. |
| U200E:11 |
Control Module Output Power B: Circuit Short To Ground |
GO to Pinpoint Test AO
. |
| U200E:12 |
Control Module Output Power B: Circuit Short To Battery |
GO to Pinpoint Test AO
. |
| U200E:1A |
Control Module Output Power B: Circuit Resistance Below Threshold |
GO to Pinpoint Test AO
. |
| U3000:49 |
Control Module: Internal Electronic Failure |
REPAIR all other OCSM DTCs first. REPEAT the self-test. If U3000:49 returns, INSTALL a new OCSM. REFER to Occupant Classification System Module (OCSM) -- Manual Seat Track
or Occupant Classification System Module (OCSM) -- Power Seat Track
. |
| U3000:53 |
Control Module: Deactivated |
CLEAR all OCSM DTCs and REPEAT the self-test. If U3000:53 returns, INSTALL a new Occupant Classification System Module (OCSM) -- Manual Seat Track
or Occupant Classification System Module (OCSM) -- Power Seat Track
. |
| U3000:54 |
Control Module: Missing Calibration |
CARRY OUT the OCS Reset. REFER to Occupant Classification Sensor (OCS) System Reset
. |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test AD
. |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AD
. |