Specifications Index
TAURUS POLICE INTERCEPTOR - SEDAN COMMON SPECIFICATIONS & PROCEDURES INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Specifications | |||
| Torque | Specifications | |||
| Axle Nut/Hub Nut | ||||
| Torque | 258 Ft. Lbs (350 N.m) | |||
| Battery | Specifications | |||
| Brakes | ||||
| Bleeding Sequence | R/R, L/R, R/F, L/F Brake System Bleeding |
|||
| Disc Brakes w/Torque | ||||
| Front | Refer to the appropriate procedure in Removal And Installation | |||
| Rear | Specifications | |||
| Charging - Generator | ||||
| 2.0L GTDI | For the tightening sequence, refer to Generator -- 2.0L GTDI 25 Nm (18 lb-ft) |
|||
| 3.5L GTDI, 3.5L Ti-VCT, 3.7L Ti-VCT | Generator Stud Bolt: 8 Nm (71 lb-in) Stud Nut: 47 Nm (35 lb-ft) Lower Bolt: 47 Nm (35 lb-ft) |
|||
| Drive Belts | ||||
| Adjustment | Accessory Drive | |||
| Belt Routing | Component Location | |||
| Engine Cooling | ||||
| General Service Specifications | Specifications | |||
| Radiator Cap Pressure | 14 psi (96 kPa) | |||
| Thermostat R & I | ||||
| 2.0L GTDI | Thermostat Housing - 2.0L GTDI | |||
| 3.5L GTDI | Thermostat - 3.5L GTDI | |||
| 3.5L Ti-VCT, 3.7L Ti-VCT | Thermostat - 3.5L Ti-VCT, 3.7L Ti-VCT | |||
| Water Pump R & I | ||||
| 2.0L GTDI | Coolant Pump - 2.0L GTDI | |||
| 3.5L GTDI | Coolant Pump - 3.5L GTDI | |||
| 3.5L Ti-VCT, 3.7L Ti-VCT | Coolant Pump - 3.5L Ti-VCT, 3.7L Ti-VCT | |||
| Engine Mechanical | ||||
| 2.0L GTDI | ||||
| Compression | Specifications | |||
| Oil pressure (hot @ 2, 000 rpm) | 200 kPa (29.01 psi) - 268 kPa (38.87 psi) | |||
| Overhaul | Specifications | |||
| Torque | Specifications | |||
| 3.5L Ti-VCT | ||||
| Compression | Specifications | |||
| Oil Pressure | Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature | |||
| Overhaul | Specifications | |||
| Torque | Specifications . | |||
| 3.5L GTDI | ||||
| Compression | \Specifications | |||
| Oil Pressure | Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature | |||
| Overhaul | Specifications | |||
| Torque | Specifications | |||
| 3.7L Ti-VCT | ||||
| Compression | Specifications | |||
| Oil Pressure | Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature | |||
| Overhaul | Specifications | |||
| Torque | Specifications | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 2.0L GTDI | For tightening sequence, refer to Flexplate Stage 1: Tighten to 50 Nm (37 lb-ft) Stage 2: Tighten to 80 Nm (50 lb-ft) Stage 3: Tighten to 112 Nm (83 lb-ft) |
|||
| 3.5L Ti-VCT | For tightening sequence, refer to Flexplate 80 Nm (59 lb-ft) |
|||
| 3.5L GTDI | For tightening sequence, refer to Flexplate 80 Nm (59 lb-ft) |
|||
| 3.7L Ti-VCT | For tightening sequence, refer to Flexplate 80 Nm (59 lb-ft) |
|||
| Fuel System | ||||
| Fuel Filter Location | Located in fuel tank as part of the fuel pump module. | |||
| Fuel Filter R & I | Fuel Pump Module | |||
| Pressure Release Procedure | Fuel System Pressure Release . | |||
| Pressure Specification | Specifications | |||
| Fuel Pressure Test Procedure | Fuel System Pressure Test | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Wires (Routing) | Coil on plug | |||
| Spark Plug | ||||
| 2.0L GTDI | ||||
| Type | CYFS 12Y PCT | |||
| Gap | 0.7 mm (0.028 in) - 0.8 mm (0.031 in) | |||
| Torque | 12 Nm (106 lb-in) | |||
| 3.5L Ti-VCT | ||||
| Type | CYFS 12 YT4 | |||
| Gap | 1.30 mm (0.051 in) | |||
| Torque | 133 Inch Lbs. (15 N.m) | |||
| 3.5L GTDI | ||||
| Type | CYFS 12 YT4 | |||
| Gap | 0.81-0.97 mm (0.032-0.038 in) | |||
| Torque | 133 Inch Lbs. (15 N.m) | |||
| 3.7L Ti-VCT | ||||
| Type | CYFS 12F 5 | |||
| Gap | 1.30 mm (0.051 in) | |||
| Torque | 133 Inch Lbs. (15 N.m) | |||
| Starting | ||||
| Starter | Specifications | |||
| Torque | ||||
| 2.0L GTDI | Starter Motor Studbolts: 48 Nm (35 lb-ft) | |||
| 3.5L GTDI | Starter Motor Studbolts: 48 Nm (35 lb-ft) | |||
| 3.5L Ti-VCT | Starter Motor Studbolts: 48 Nm (35 lb-ft) | |||
| 3.7L Ti-VCT | Starter Motor Studbolts: 48 Nm (35 lb-ft) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Specifications | |||
| Torque | Specifications | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | All except Police Vehicles: 100 Ft. Lbs. (135 N.m) Police Vehicles: 110 Ft. Lbs. (149 N.m) |
|||