| B11C7:46 |
High Beam Sensor: Calibration / Parameter Memory Failure |
PROGRAM the IPM-A. REFER to Programmable Module Installation (PMI) in Module Configuration
. REPEAT the IPM-A self-test. If the DTC is returns, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| B11C7:97 |
High Beam Sensor: Component or System Operation Obstructed or Blocked |
REFER to Exterior Lighting
. |
| B1286:14 |
Interior Mirror: Circuit Short To Ground or Open |
GO to Pinpoint Test F
. |
| B12D8:11 |
Mirror Heater Output: Circuit Short To Ground |
GO to Pinpoint Test G
. |
| B12D8:13 |
Mirror Heater Output: Circuit Open |
GO to Pinpoint Test G
. |
| B13A6:14 |
Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground or Open |
Lane Keeping System
. |
| C1001:78 |
Vision System Camera: Alignment or Adjustment Incorrect |
Sets in continuous memory when a new interior mirror has been installed without performing the camera alignment. The camera alignment is initiated using the scan tool. |
| U0100:87 |
Lost Communication With ECM/PCM "A": Missing Message |
GO to Pinpoint Test H
. |
| U0104:87 |
Lost Communication With Cruise Control Module: Missing Message |
GO to Pinpoint Test I
. |
| U0131:87 |
Lost Communication With Power Steering Control Module: Missing Message |
GO to Pinpoint Test J
. |
| U0140:87 |
Lost Communication With Body Control Module: Missing Message |
GO to Pinpoint Test K
. |
| U0151:87 |
Lost Communication With Restraints Control Module: Missing Message |
GO to Pinpoint Test L
. |
| U0155:87 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message |
GO to Pinpoint Test M
. |
| U0212:87 |
Lost Communication With Steering Column Control Module: Missing Message |
GO to Pinpoint Test N
. |
| U0232:87 |
Lost Communication With Side Obstacle Detection Control Module - Left: Missing Message |
GO to Pinpoint Test O
. |
| U0233:87 |
Lost Communication With Side Obstacle Detection Control Module - Right: Missing Message |
GO to Pinpoint Test O
. |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
This DTC can set due to a fault in the PCM. PERFORM a self-test of the PCM and DIAGNOSE any PCM DTCs present, REFER to Electronic Engine Controls
. |
| U0405:00 |
Invalid Data Received From Cruise Control Module: No Sub Type Information |
This DTC can set due to a fault in the C-CM. PERFORM a self-test of the C-CM and DIAGNOSE any C-CM DTCs present, REFER to Collision Avoidance
. |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
This DTC can set due to a fault in the BCM. PERFORM a self-test of the BCM and DIAGNOSE any BCM DTCs present, REFER to Multifunction Electronic Modules
. |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
This DTC can set due to a fault in the IPC. PERFORM a self-test of the IPC and DIAGNOSE any IPC DTCs present, REFER to Information Center - Instrumentation, Message Center, And Warning Chimes
. |
| U0429:00 |
Invalid Data Received From Steering Column Control Module: No Sub Type Information |
This DTC can set due to a fault in the SCCM. PERFORM a self-test of the SCCM and DIAGNOSE any SCCM DTCs present, REFER to Steering Column Switches
. |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
This DTC can set due to a fault in the RCM. PERFORM a self-test of the RCM and DIAGNOSE any RCM DTCs present, REFER to Supplemental Restraint System
. |
| U1000:11 |
Solid State Driver Protection Active - Driver Disabled: Circuit Short To Ground |
The IPM-A has temporarily disabled an output because an excessive current draw exists from a short to ground). The IPM-A cannot enable the output until the cause of the short is corrected. ADDRESS all other IPM-A DTCs first. After the cause of the concern is corrected, CLEAR the DTCs. REPEAT the IPM-A self-test. |
| U201A:54 |
Control Module Main Calibration Data: Missing Calibration |
PROGRAM the IPM-A. REFER to Programmable Module Installation (PMI) in Module Configuration
. REPEAT the IPM-A self-test. If the DTC is returns, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
PROGRAM the IPM-A. REFER to Programmable Module Installation (PMI) in Module Configuration
. REPEAT the IPM-A self-test. If the DTC is returns, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
PROGRAM the IPM-A. REFER to Programmable Module Installation (PMI) in Module Configuration
. REPEAT the IPM-A self-test. If the DTC is returns, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
PROGRAM the IPM-A. REFER to Programmable Module Installation (PMI) in Module Configuration
. REPEAT the IPM-A self-test. If the DTC is returns, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U3000:42 |
Control Module: General Memory Failure |
INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U3000:49 |
Control Module: Internal Electronic Failure |
ADDRESS all other IPM-A DTCs. After all other DTCs have been addressed, INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U3000:93 |
Control Module: No Operation |
INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |
| U3000:96 |
Control Module: Component Internal Failure |
INSTALL a new interior mirror. REFER to Interior Rear View Mirror
. |