| B120C:11 |
Heater for Windshield Mounted Sensor: Circuit Short To Ground |
GO to Pinpoint Test C |
| B120C:13 |
Heater for Windshield Mounted Sensor: Circuit Open |
GO to Pinpoint Test C |
| B13A6:14 |
Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground or Open |
GO to Pinpoint Test A |
| C0072:00 |
Brake Temperature Too High: No Sub Type Information |
GO to Pinpoint Test S |
| C1001:54 |
Vision System Camera: Missing Calibration |
GO to Pinpoint Test T |
| C1001:78 |
Vision System Camera: Alignment or Adjustment Incorrect |
GO to Pinpoint Test T |
| C1001:97 |
Vision System Camera: Component or System Operation Obstructed or Blocked |
GO to Pinpoint Test U |
| C1001:98 |
Vision System Camera: Component or System Over Temperature |
GO to Pinpoint Test V |
| C1A67:08 |
Forward Looking Sensor: Bus Signal/Message Failures |
GO to Pinpoint Test W |
| U0100:00 |
Loss Communication with ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test E |
| U0103:00 |
Loss Communication With Gear Shift Control Module: No Sub Type Information |
GO to Pinpoint Test F |
| U0121:00 |
Loss Communication With Anti-Lock Brake System Control Module: No Sub Type Information |
GO to Pinpoint Test G |
| U0130:00 |
Lost Communication With Steering Effort Control Module: No Sub Type Information |
GO to Pinpoint Test R |
| U0131:00 |
Lost Communication With Power Steering Control Module: No Sub-Type Information |
GO to Pinpoint Test J |
| U0140:00 |
Lost Communication With Body Control Module: No Sub-Type Information |
GO to Pinpoint Test K |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub-Type Information |
GO to Pinpoint Test L |
| U0155:00 |
Lost Communication With Instrument Panel Cluster Control Module: No Sub-Type Information |
GO to Pinpoint Test M |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub-Type Information |
GO to Pinpoint Test N |
| U0232:00 |
Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information |
GO to Pinpoint Test H |
| U0233:00 |
Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information |
GO to Pinpoint Test I |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test X |
| U0404:86 |
Invalid Data Received from Gear Shift Control Module A: Signal Invalid |
GO to Pinpoint Test Y |
| U0405:64 |
Invalid Data Received From Cruise Control Module: Signal Plausibility Failure |
GO to Pinpoint Test Z |
| U0416:86 |
Invalid Data Received From Vehicle Dynamics Control Module: Signal Invalid |
GO to Pinpoint Test AA |
| U0418:86 |
Invalid Data Received from Brake System Control Module "A": Signal Invalid |
GO to Pinpoint Test AB |
| U0419:86 |
Invalid Data Received From Steering Effort Control Module: Signal Invalid |
GO to Pinpoint Test AC |
| U0420:86 |
Invalid Data Received from Power Steering Control Module "A": Signal Invalid |
GO to Pinpoint Test AD |
| U0422:82 |
Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test AE |
| U0423:82 |
Invalid Date Received From Instrument Panel Cluster Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test AF |
| U0423:86 |
Invalid Date Received From Instrument Panel Cluster Control Module: Signal Invalid |
GO to Pinpoint Test AF |
| U0429:86 |
Invalid Data Received From Steering Column Control Module: Signal Invalid |
GO to Pinpoint Test AG |
| U0452:86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test AH |
| U0533:86 |
Invalid Data Received From Side Obstacle Detection Control Module "A": Signal Invalid |
GO to Pinpoint Test AI |
| U0534:86 |
Invalid Data Received From Side Obstacle Detection Control Module "B": Signal Invalid |
GO to Pinpoint Test AJ |
| U1000:11 |
Solid State Driver Protection Activated: Circuit Short To Ground |
GO to Pinpoint Test AK |
| U2018:51 |
Control Module Software#3: Not Programmed |
GO to Pinpoint Test AL |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AM |
| U2101:64 |
Control Module Configuration Incompatible: Signal Plausibility Failure |
GO to Pinpoint Test AN |
| U2300:55 |
Central Configuration: Not Configured |
GO to Pinpoint Test AO |
| U2300:64 |
Central Configuration: Signal Plausibility Failure |
GO to Pinpoint Test AP |
| U3000:41 |
Control Module: General Check Sum Failure |
GO to Pinpoint Test AQ |
| U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test AR |
| U3000:44 |
Control Module: Data Memory Failure |
GO to Pinpoint Test AS |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AS |
| U3000:64 |
Control Module: Signal Plausibility Failure |
GO to Pinpoint Test AT |
| U3003:16 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test P |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test Q |