LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2021 >> Edge ST-Line, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 129 (Lane Keeping System) >> Diagnosis And Testing >> Lane Keeping System >> IPMA DTC Chart
April 5, 2026: LEMON Manuals is launched! Read the announcement.

IPMA DTC Chart

WARNING: This page is about a different car, the 2018 Ford F-550 Super Duty, 2018 Ford F-450 Super Duty, 2018 Ford F-350 Super Duty, and 2018 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .

DTC Description Action
B11C7:46 High Beam Sensor: Calibration/Parameter Memory Failure DIAGNOSE the automatic high beam feature. Refer to: Headlamps .
B11C7:97 High Beam Sensor: Component or System Operation Obstructed or Blocked DIAGNOSE the automatic high beam feature. Refer to: Headlamps .
B1286:14 Interior Mirror: Circuit Short To Ground or Open See DTC Chart: IPMA. Refer to: Rear View Mirrors .
B12D8:11 Mirror Heater Output: Circuit Short To Ground GO to Pinpoint Test C 
B12D8:13 Mirror Heater Output: Circuit Open GO to Pinpoint Test C 
B13A6:14 Lane Departure Warning (LDW) Switch Input Circuit Short To Ground or Open GO to Pinpoint Test A 
C1001:78 Vision System Camera: Alignment or Adjustment Incorrect This continuous memory DTC sets when a new IPMA has been installed without performing the camera alignment. PERFORM the camera alignment using a diagnostic scan tool.
U0100:87 Lost Communication With ECM/PCM "A": Missing Message GO to Pinpoint Test E 
U0130:87 Lost Communication With Steering Effort Control Module: Missing Message GO to Pinpoint Test F 
U0140:87 Lost Communication With Body Control Module: Missing Message GO to Pinpoint Test G 
U0151:87 Lost Communication With Restraints Control Module: Missing Message GO to Pinpoint Test H 
U0155:87 Lost Communication With Instrument Panel Cluster (IPC): Missing Message GO to Pinpoint Test I 
U0212:87 Lost Communication With Steering Column Control Module: Missing Message GO to Pinpoint Test J 
U0401:00 Invalid Data Received From ECM/PCM A: No Sub Type Information This continuous memory DTC can set due to a fault in the PCM or an input to the PCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the PCM. See Electronic Engine Control, PCM DTC Chart. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom.
U0405:00 Invalid Data Received From Cruise Control Module: No Sub Type Information This continuous memory DTC can set due to a fault in the CCM or an input to the CCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the CCM. Refer to: Cruise Control . If no Diagnostic Trouble Codes (DTCs) are present in the CCM, DIAGNOSE the observable symptom.
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information This continuous memory DTC can set due to a fault in the BCM or an input to the BCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the BCM. Refer to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
U0423:00 Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information This continuous memory DTC can set due to a fault in the IPC or an input to the IPC. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the IPC. Refer to: Instrumentation, Message Center and Warning Chimes . If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom.
U0429:00 Invalid Data Received From Steering Column Control Module: No Sub Type Information This continuous memory DTC can set due to a fault in the SCCM or an input to the SCCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the SCCM. Refer to: Steering Wheel and Column Electrical Components . If no Diagnostic Trouble Codes (DTCs) are present in the SCCM, DIAGNOSE the observable symptom.
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information This continuous memory DTC can set due to a fault in the RCM or an input to the RCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the RCM. Refer to: Airbag Supplemental Restraint System (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom.
U1000:11 Solid State Driver Protection Activated: Circuit Short To Ground This continuous memory DTC set in the IPMA when the IPMA has temporarily disabled the IPMA camera heated windshield element output because an excessive current draw exists (such as a short to ground). The IPMA cannot enable the output driver until the short is corrected. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self-test to enable the output driver.
U201A:54 Control Module Main Calibration Data: Missing Calibration CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror .
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror .
U2200:00 Control Module Configuration Memory Corrupt: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror .
U3000:42 Control Module: General Memory Failure ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. If this continuous memory DTC is still present after all other Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. Refer to: Interior Rear View Mirror .
U3000:49 Control Module: Internal Electronic Failure The IPMA has permanently disabled the IPMA camera heated windshield element output because an excessive current draw has occurred more times than the module can withstand. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). If this continuous memory DTC is still present after all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. Refer to: Interior Rear View Mirror .
U3000:93 Control Module: No Operation ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). If this DTC is still present on-demand or in continuous memory after all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. Refer to: Interior Rear View Mirror .
U3000:96 Control Module: Component Internal Failure ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). After all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. Refer to: Interior Rear View Mirror .
scientia non olet · About LEMON Manuals