Pinpoint Tests G: Stability Control Sensor Signal Failure Faults

Refer to the Vehicle Dynamc Systems wiring diagrams for schematic and connector information.

1. G1: CHECK THE WHEELS AND TIRES 
   • Inspect the wheels and tires for any damage or excessive wear.
   • Verify all wheels and tires are the same size and match the size indicated on the VC label.
   • Verify the inflation pressure of all 4 tires is correct as indicated on the VC label.
   • Are the wheels and tires OK? 
2. G2: CHECK THE COMMUNICATION NETWORK 
   • Ignition ON, engine OFF.
   • Press the Read Vehicle Information button to view the results of the modules communicating on the network
   • Retrieve the continuous memory DTCs.
   • Does the RCM pass the Network Test? 

     Yes	No
     Go to  G3.	REFER to the Module Communications Network article to diagnose the RCM does not communicate with the scan tool.

3. G3: RETRIEVE ALL DTCS FROM THE RCM 

   Carry out the RCM self-test.

   • Are any DTCs present? 

     Yes	No
     DIAGNOSE the RCM DTCs first. REFER to the Supplemental Restraint System article.	Go to  G4.

4. G4: CHECK THE ABS MODULE DTCS 
   • Ignition ON, engine OFF.

     Carry out the ABS self-test.

   • Is DTC U0151:xx or U0452:xx present and active in the ABS module? 

     Yes	No
     GO to PINPOINT TEST BH .	Go to  G5.

5. G5: CHECK THE RCM INSTALLATION AND MOUNTING SURFACE 
   WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
   • Ignition OFF.
   • Wait one minute.
   • RCM_A connector disconnected. (C310A)
   • RCM_B connector disconnected. (C310B)
   • Inspect the RCM installation, make sure the fasteners are fully seated and tightened to specifications. Refer to the Supplemental Restraint System article.
   • Inspect the RCM mounting surface for damage, corrosion or dirt.
   • the RCM installed correctly and is the mounting surface clean and free from damage? 

     Yes	No
     Go to  G7.	CLEAN or REPAIR the mounting surface or INSTALL a new RCM as necessary. REFER to the Supplemental Restraint System article.

6. G6: CHECK THE YAW RATE SENSOR INSTALLATION AND MOUNTING SURFACE 
   • Ignition OFF.
   • Yaw Rate Sensor connector disconnected.
   • Inspect the yaw rate sensor installation, make sure the fasteners are fully seated and tightened to specifications. Refer to the Anti-Lock Brake System (ABS) and Stability Control article.
   • Inspect the yaw rate sensor mounting surface for damage, corrosion or dirt.
   • the yaw rate sensor installed correctly and is the mounting surface clean and free from damage? 

     Yes	No
     Go to  G7.	CLEAN or REPAIR the mounting surface or INSTALL a new yaw rate sensor as necessary. REFER to the Anti-Lock Brake System (ABS) and Stability Control article.

7. G7: VERIFY STABILITY CONTROL SENSOR CALIBRATION 
   • Ignition ON, engine OFF.
     NOTE: The vehicle must be on level ground and at a complete standstill during sensor calibration. Any vehicle movement results in a failed calibration.
   • Does the scan tool routine pass? 

     Yes	No
     Go to  G8.	Go to  G9.

8. G8: RECHECK THE ABS MODULE DTCS 
   • Clear the ABS DTCs.
   • Ignition OFF.
   • Ignition ON, engine OFF.
   • Test drive the vehicle above 20 km/h (12 mph) and make at lest 1 left turn and 1 right turn.

     Carry out the ABS self-test.

   • Are any of the DTCs listed in the DTC Fault Trigger Conditions table present in the ABS module? 

     Yes	No
     Go to  G9.	The condition causing the concern is no longer present. The concern was most likely caused by an incomplete calibration or a previously failed calibration of the stability control sensors.

9. G9: CHECK THE PRIVATE HS-CAN CIRCUITS FOR A SHORT TO VOLTAGE 
   • Ignition OFF.
   • Yaw Rate Sensor connector disconnected.
10. G10: CHECK THE PRIVATE HS-CAN CIRCUITS FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Measure the resistance between:
11. G11: CHECK THE PRIVATE HS-CAN CIRCUITS FOR A SHORT TOGETHER 
    • Measure the resistance between:
12. G12: CHECK THE PRIVATE HS-CAN CIRCUITS FOR AN OPEN 
    • Measure the resistance between:
13. G13: CHECK FOR VOLTAGE TO THE YAW RATE SENSOR 
    • Ignition ON, engine OFF.
    • Measure the voltage between:

      (+) Yaw Rate Sensor Connector, Harness Side	(-)
      IGN START/RUN	Ground

    • Is the voltage greater than 10 volts? 

      Yes	No
      Go to  G14.	VERIFY BCM fuse 18 (7.5A) is OK. If the fuse is not OK, REFER to the OEM Electrical Wiring Diagram Introduction article to determine the cause of the circuit short. If the fuse is OK, REPAIR the circuit for an open condition.

14. G14: CHECK THE YAW RATE SENSOR GROUND CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Measure the resistance between:

      (+) Yaw Rate Sensor Connector, Harness Side	(-)
      GND	Ground

    • Is the resistance greater than 10, 000 ohms? 

      Yes	No
      Go to  G15.	REPAIR the circuit.

15. G15: VERIFY ALL WIRING CONNECTIONS 
    • Using a good light source, inspect all disconnected electrical connectors for the following:
      • corrosion - install new connector or terminal and clean the module pins
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary
    • Are the connectors free of corrosion, damaged pins, bent pins, pushed-out pins and spread terminals? 
16. G16: CHECK THE RCM FOR CORRECT OPERATION 
17. G17: CHECK THE YAW RATE SENSOR FOR CORRECT OPERATION