Common Specifications & Procedures

ESCAPE COMMON SPECIFICATIONS & PROCEDURES

	System		Specification/Procedure
Air Conditioning
Service			SPECIFICATIONS
Torque			Refer to appropriate procedure(s) in REMOVAL AND INSTALLATION .
Axle Nut/Hub Nut 98 lb.ft (133 Nm)
Battery			Not available. Refer to the appropriate service information.
Brakes
Bleeding Sequence			Refer to the appropriate procedure GENERAL PROCEDURES .
Disc Brakes w/Torque
Front Disc			Refer to approriate component procedure in REMOVAL AND INSTALLATION
Rear Disc			Refer to approriate component procedure in REMOVAL AND INSTALLATION
Charging
Generator w/Torque
	1.5L
		Generator StudBolt	18 lb.ft (25 Nm)
		Generator Bolt	18 lb.ft (25 Nm)
		B+ Wire Nut	155 lb.in (17.5 Nm)
	2.0L
		Generator Bolt	18 lb.ft (25 Nm)
		B+ Wire Nut	155 lb.in (17.5 Nm)
	2.5L		N/A
Drive Belts
Adjustment
	1.5L		Accessory Drive Belt - Vehicles Built Up To: 1-October-2020 or Accessory Drive Belt - Vehicles Built From: 1-October-2020
	2.0L		Accessory Drive Belt
	2.5L		N/A
Belt Routing
	1.5L		Accessory Drive - Component Location
	2.0L		Accessory Drive - Component Location
	2.5L		N/A
Engine Cooling
General Service Specifications
	1.5L		SPECIFICATIONS
	2.0L		SPECIFICATIONS
	2.5L		SPECIFICATIONS
Radiator Pressure Cap			17.4-21.7 psi (120-150 kPa)
Thermostat R & I
	1.5L		Thermostat Housing
	2.0L		Thermostat
	2.5L		Thermostat Housing
Water Pump R & I
	1.5L		Coolant Pump
	2.0L		Coolant Pump
	2.5L		Coolant Pump
Engine Mechanical
1.5L
Compression			SPECIFICATIONS
	Minimum oil pressure at ECT of 175.9 deg. F (80 deg. C) and an engine speed of 850 rpm		15 psi (1.035 bar)
Minimum oil pressure at an ECT of 175.9 deg. F (80 deg. C) and an engine speed of 2000 rpm			19.0 psi (1.31 bar)
Overhaul			SPECIFICATIONS
Torque			Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION .
2.0L
Compression			SPECIFICATIONS
	Oil Pressure @ 1, 500 rpm		27.6 -37.7 psi (190 -260 kPa)
	Overhaul		SPECIFICATIONS
	Torque		Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION
2.5L
	Compression		SPECIFICATIONS
	Oil pressure (hot @ 2000 rpm)		29-60 psi (200-414 kPa)
	Overhaul		SPECIFICATIONS
	Torque		Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION .
Fluid Specifications			See FLUIDS under MAINTENANCE tab.
Flywheel/Flex Plate Torque
1.5L
	Stage 1		89 lb.in (10 Nm)
Stage 2			177 lb.in (20 Nm)
Stage 3			22 lb.ft (30 Nm)
Stage 4			90°
2.0L
	Stage 1		37 Ft. Lbs. (50 N.m)
Stage 2			59 Ft. Lbs. (80 N.m)
Stage 3			83 Ft. Lbs. (112 N.m)
2.5L
	Stage 1		37 Ft. Lbs. (50 N.m)
Stage 2			59 Ft. Lbs. (80 N.m)
Stage 3			83 Ft. Lbs. (112 N.m)
Fuel System
Fuel Filter Location			Lifetime fuel filter (serviced as part of the Fuel Pump module).
Fuel Filter R & I
	1.5L		Fuel Pump and Sender Unit
2.0L			Fuel Pump and Sender Unit
2.5L			Fuel Pump and Sender Unit
Pressure Release Procedure
	1.5L		Fuel System Pressure Release
2.0L			Fuel System Pressure Release
2.5L			Fuel System Pressure Release
Pressure Specification
	1.5L		50.8 -87.7 psi (350 -605 kPa)
2.0L			50.8 -87.7 psi (350 -605 kPa)
2.5L			50-62 psi (350-428 kPa)
Fuel Pressure Test Procedure
	1.5L		Fuel System Pressure Check
2.0L			Fuel System Pressure Check
2.5L			Fuel System Pressure Check
Ignition
Firing Order & Cylinder Identification
1.5L			1-2-3
	2.0L & 2.5L		1-3-4-2
Spark Plugs
1.5L
	Number		CYFS 12Y PCT
Gap			.8 mm (0.031 in)
Torque			159 lb.in (18 Nm)
2.0L
	Number		CYFS 12Y PCT
Gap			.030 in (.75mm)
Torque			106 In. Lbs. (12 N.m)
2.5L
	Number		AYFS 32Y R
	Gap		0.051 in (1.3 mm)
	Torque		106 In. Lbs. (12 N.m)
Starter
Starter Motor Bracket Nuts 1.5L & 2.0L			97 lb.in (11 Nm)
Starter Motor Studs 1.5L & 2.0L			35 lb.ft (48 Nm)
Starter Motor Battery Cable Nut 1.5L & 2.0L			106 lb.in (12 Nm)
Starter Motor Control Wire Nut 1.5L & 2.0L			53 lb.in (6 Nm)
Wheel Alignment
Adjustment Specifications			SPECIFICATIONS
Torque			Refer to the appropriate procedure in GENERAL PROCEDURES
Wheel & Tire
Wheel Lug Nut Torque			100 lb.ft (135 Nm)