Steering Wheel And Column Switches DTCS
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B108A:01 | Start Button: General Electrical Failure | GO to Pinpoint Test F |
| B108A:24 | Start Button: Signal Stuck High | GO to Pinpoint Test F |
| B108A:9E | Start Button: Stuck On | GO to Pinpoint Test F |
| B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test C |
| B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test F |
| B1240:11 | Start Button Mode Indicator: Circuit Short To Ground | GO to Pinpoint Test G |
| B1240:15 | Start Button Mode Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test G |
| B1240:15 | Start Button Mode Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test H |
| B1310:12 | Run/Start Control: Circuit Short To Battery | GO to Pinpoint Test C |
| B1310:12 | Run/Start Control: Circuit Short To Battery | GO to Pinpoint Test F |
| B1310:14 | Run/Start Control: Circuit Short To Ground Or Open | GO to Pinpoint Test C |
| B1310:14 | Run/Start Control: Circuit Short To Ground Or Open | GO to Pinpoint Test F |
| B1472:12 | Ignition Key Removal Inhibit: Circuit Short To Battery | GO to Pinpoint Test E |
| B1472:14 | Ignition Key Removal Inhibit: Circuit Short To Ground Or Open | GO to Pinpoint Test E |
| U300A:01 | Ignition Switch: General Electrical Failure | GO to Pinpoint Test L |
| P2534:00 | Ignition Switch On/Start Position Circuit Low: No Sub Type Information | GO to Pinpoint Test F |
| P2535:00 | Ignition Switch On/Start Position Circuit High: No Sub Type Information | GO to Pinpoint Test F |
| B112B:04 | Steering Wheel Module: System Internal Failures | GO to Pinpoint Test I |
| B112B:44 | Steering Wheel Module: Data Memory Failure | GO to Pinpoint Test I |
| B112B:45 | Steering Wheel Module: Program Memory Failure | GO to Pinpoint Test I |
| B112B:46 | Steering Wheel Module: Calibration/Parameter Memory Failure | GO to Pinpoint Test I |
| B112B:49 | Steering Wheel Module: Internal Electronic Failure | GO to Pinpoint Test I |
| B135C:11 | Heater Element: Circuit Short To Ground | GO to Pinpoint Test M |
| B135C:13 | Heater Element: Circuit Open | GO to Pinpoint Test M |
| U0126:87 | Lost Communication With Steering Angle Sensor Module: Missing Message | GO to Pinpoint Test I |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test N |
| U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test N |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test N |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test N |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test N |
| U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test N |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test O |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test O |
| U210A:11 | Temperature Sensor: Circuit Short To Ground | GO to Pinpoint Test M |
| U210A:13 | Temperature Sensor: Circuit Open | GO to Pinpoint Test M |
| U210A:29 | Temperature Sensor: Signal Invalid | GO to Pinpoint Test M |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test I |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test J |
| U3003:A3 | Battery Voltage: System Voltage High | GO to Pinpoint Test K |