Common Specifications & Procedures

EDGE COMMON SPECIFICATIONS & PROCEDURES

System			Specifications/Procedures
Air Conditioning
Service			Specifications
Torque			Refer to the appropriate component in Removal And Installation .
Axle Nut/Hub Nut
Torque			148 lb.ft (200 Nm)
Battery			Specifications
Brakes
Bleeding Sequence			RR, LR, RF, LF Brake System Pressure Bleeding
Front Disc Brakes w/Torque			Refer to appropriate component in Removal And Installation
Rear Disc Brakes w/Torque			Refer to appropriate component in Removal And Installation
Charging
Generator w/Torque
	2.0L EcoBoost (184kW/250PS) - MI4		Generator Bolt: 18 lb.ft (25 Nm)
	2.7L EcoBoost (238kW/324PS)		Generator Bolt and Stud Nut: 35 lb.ft (47 Nm) Generator Stud: 71 lb.in (8 Nm)
Drive Belts
Adjustment
		2.0L EcoBoost (184KW/250PS) - MI4	Accessory Drive Belt
		2.7L EcoBoost (238kW/324PS)	Accessory Drive Belt
Belt Routing
	2.0L EcoBoost (184KW/250PS) - MI4		Accessory Drive - Component Location
	2.7L EcoBoost (238kW/324PS)		Accessory Drive - Component Location
Engine Cooling
General Service Specifications
	2.0L EcoBoost (184KW/250PS) - MI4		Specifications
	2.7L EcoBoost (238kW/324PS)		Specifications
Radiator Cap Pressure			145 kPa (21 psi)
	Radiator Pressure Test (Removed From The Vehicle)		138 kPa (20 psi)
Thermostat R & I
	2.0L		Thermostat Housing
	2.7L		Thermostat
Water Pump R & I
	2.0L		Coolant Pump
	2.7L		Coolant Pump
Engine Mechanical
2.0L
	Compression		Specifications
	Oil pressure at 1, 500 rpm with engine oil temperature between 121.9 - 175.9°F (50 - 80°C)		27.6 - 37.7 psi (190 - 260 kPa)
	Overhaul		Specifications
	Torque		Refer to the appropriate procedure in Removal And Installation
2.7L
Compression			Specifications
Oil Pressure Reading 1 (Minimum average oil pressure at 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park.)			21 psi (144.8 kPa)
		Oil Pressure Reading 2 (Minimum average oil pressure at 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected))	Reading 1 value plus 8 psi (55.1 kPa)
Overhaul			Specifications
Torque			Refer to appropriate component in Removal And Installation (1 of 2) and Removal And Installation (2 of 2)
Fluid Specifications			See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
2.0L			For tightening sequence, refer to Flexplate . Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm)
2.7L			For Tightening Sequence Refer to Flexplate 59 lb.ft (80 Nm)
Fuel System
Fuel Filter Location			Located in fuel tank as part of Fuel Pump Module.
Fuel Filter R & I
	2.0L		Fuel Pump And Sender Unit
	2.7L		Fuel Pump And Sender Unit
Pressure Release Procedure
	2.0L		Fuel System Pressure Release
	2.7L		Fuel System Pressure Release
Pressure Specification
	2.0L		Specifications
	2.7L		Specifications
Fuel Pressure Test Procedure
	2.0L		Fuel System Pressure Check
	2.7L		Fuel System Pressure Check
Ignition
Firing Order & Cylinder Identification
Ignition Wires (Routing)			Engines are equipped with Coil-on-plug ignition.
Spark Plugs
2.0L
	Type		CYFS 12Y PCT
	Gap		0.030 In. (0.75 mm)
	Torque		106 In. Lbs. (12 N.m)
2.7L
Type			CYFS 12Y RT3
Gap			0.028-0.031 in (0.7-0.8 mm)
Torque			133 In. Lbs. (15 N.m)
Starting
Starter
	2.0L		Specifications
	2.7L		Specifications
Torque
	2.0L		For removal and installation, refer to Starter Motor .
	2.7L		For removal and installation, refer to Starter Motor .
Wheel Alignment
Adjustment Specifications			Specifications
Torque			Refer to the appropriate procedure in General Procedures
Wheel & Tire
Wheel Lug Nut Torque			For tightening sequence, refer to Wheel And Tire 162 lb.ft (220 Nm)