| B10DF:46 |
Master Cylinder Isolation Valve: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AL |
| C0001:01 |
TCS Control Channel 'A' Valve 1: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0002:01 |
TCS Control Channel 'A' Valve 2: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0003:01 |
TCS Control Channel 'B' Valve 1: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0004:01 |
TCS Control Channel 'B' Valve 2: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0010:01 |
Left Front Inlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0011:01 |
Left Front Outlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0014:01 |
Right Front Inlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0015:01 |
Right Front Outlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0018:01 |
Left Rear Inlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0019:01 |
Left Rear Outlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C001C:01 |
Right Rear Inlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C001D:01 |
Right Rear Outlet Control: General Circuit/Electrical Failure |
GO to Pinpoint Test R |
| C0020:11 |
ABS Pump Motor Control: Circuit Short To Ground |
GO to Pinpoint Test G |
| C0020:12 |
ABS Pump Motor Control: Circuit Short To Battery |
GO to Pinpoint Test G |
| C0020:13 |
ABS Pump Motor Control: Circuit Open |
GO to Pinpoint Test G |
| C0020:16 |
ABS Pump Motor Control: Circuit Voltage Below Threshold |
GO to Pinpoint Test G |
| C0020:71 |
ABS Pump Motor Control: Actuator Stuck |
GO to Pinpoint Test G |
| C0030:07 |
Left Front Tone Wheel: Mechanical Failure |
GO to Pinpoint Test T |
| C0031:07 |
Left Front Wheel Speed Sensor: Mechanical Failure |
GO to Pinpoint Test T |
| C0031:11 |
Left Front Wheel Speed Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| C0031:15 |
Left Front Wheel Speed Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| C0031:29 |
Left Front Wheel Speed Sensor: Signal Invalid |
GO to Pinpoint Test T |
| C0031:2F |
Left Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test T |
| C0031:4A |
Left Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AD |
| C0031:64 |
Left Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test T |
| C0033:07 |
Right Front Tone Wheel: Mechanical Failure |
GO to Pinpoint Test T |
| C0034:07 |
Right Front Wheel Speed Sensor: Mechanical Failure |
GO to Pinpoint Test T |
| C0034:11 |
Right Front Wheel Speed Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| C0034:15 |
Right Front Wheel Speed Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| C0034:29 |
Right Front Wheel Speed Sensor: Signal Invalid |
GO to Pinpoint Test T |
| C0034:2F |
Right Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test T |
| C0034:4A |
Right Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AD |
| C0034:64 |
Right Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test T |
| C0036:07 |
Left Rear Tone Wheel: Mechanical Failure |
GO to Pinpoint Test T |
| C0037:07 |
Left Rear Wheel Speed Sensor: Mechanical Failure |
GO to Pinpoint Test T |
| C0037:11 |
Left Rear Wheel Speed Sensor: Circuit Short To Ground |
GO to Pinpoint Test J |
| C0037:15 |
Left Rear Wheel Speed Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test J |
| C0037:29 |
Left Rear Wheel Speed Sensor: Signal Invalid |
GO to Pinpoint Test T |
| C0037:2F |
Left Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test T |
| C0037:4A |
Left Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AD |
| C0037:64 |
Left Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test T |
| C0039:07 |
Right Rear Tone Wheel: Mechanical Failure |
GO to Pinpoint Test T |
| C003A:07 |
Right Rear Wheel Speed Sensor: Mechanical Failure |
GO to Pinpoint Test T |
| C003A:11 |
Right Rear Wheel Speed Sensor: Circuit Short To Ground |
GO to Pinpoint Test J |
| C003A:15 |
Right Rear Wheel Speed Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test J |
| C003A:29 |
Right Rear Wheel Speed Sensor: Signal Invalid |
GO to Pinpoint Test T |
| C003A:2F |
Right Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test T |
| C003A:4A |
Right Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AD |
| C003A:64 |
Right Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test T |
| C0040:64 |
Brake Pedal Switch 'A': Signal Plausibility Failure |
GO to Pinpoint Test U |
| C0044:28 |
Brake Pressure Sensor 'A': Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test U |
| C0044:47 |
Brake Pressure Sensor 'A': Watchdog/Safety μC Failure |
GO to Pinpoint Test AE |
| C0044:49 |
Brake Pressure Sensor 'A': Internal Electronic Failure |
GO to Pinpoint Test AE |
| C0044:51 |
Brake Pressure Sensor 'A': Not Programmed |
GO to Pinpoint Test AE |
| C0044:64 |
Brake Pressure Sensor 'A': Signal Plausibility Failure |
GO to Pinpoint Test AE |
| C0044:8F |
Brake Pressure Sensor 'A': Erratic |
GO to Pinpoint Test AE |
| C0047:01 |
Brake Booster Pressure Sensor: General Circuit/Electrical Failure |
GO to Pinpoint Test B |
| C0047:26 |
Brake Booster Pressure Sensor: Signal Rate Of Change Below Threshold |
GO to Pinpoint Test B |
| C0047:27 |
Brake Booster Pressure Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test B |
| C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test L |
| C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test M |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test L |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test M |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test L |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test M |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test L |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test M |
| C0061:28 |
Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AJ |
| C0061:2F |
Lateral Acceleration Sensor: Signal Erratic |
GO to Pinpoint Test AJ |
| C0061:64 |
Lateral Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AJ |
| C0062:28 |
Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AJ |
| C0062:54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AF |
| C0062:54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AJ |
| C0062:64 |
Longitudinal Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AJ |
| C0062:76 |
Longitudinal Acceleration Sensor: Wrong Mounting Position |
GO to Pinpoint Test AK |
| C0063:28 |
Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AJ |
| C0063:2F |
Yaw Rate Sensor: Signal Erratic |
GO to Pinpoint Test AJ |
| C0063:64 |
Yaw Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AJ |
| C0064:64 |
Roll Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AJ |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test V |
| C1015:08 |
Vacuum Supply: Bus Signal / Message Failure |
GO to Pinpoint Test B |
| C1015:7A |
Vacuum Supply: Fluid Leak Or Seal Failure |
GO to Pinpoint Test Z |
| C1015:7B |
Vacuum Supply: Low Fluid Level |
GO to Pinpoint Test Z |
| C1020:00 |
Brake System Fill Not Complete: No Sub Type Information |
GO to Pinpoint Test P |
| C1020:52 |
Brake System Fill Not Complete: Not Activated |
GO to Pinpoint Test P |
| C1109:64 |
Vehicle Dynamics Control Switch: Signal Plausibility Failure |
GO to Pinpoint Test K |
| C1A08:1C |
Pressure Sensor Supply: Circuit Voltage Out Of Range |
GO to Pinpoint Test AE |
| C1B14:11 |
Sensor Supply Voltage A: Circuit Short To Ground |
GO to Pinpoint Test B |
| C1B14:12 |
Sensor Supply Voltage A: Circuit Short To Battery |
GO to Pinpoint Test B |
| C1B15:1C |
Sensor Supply Voltage B: Circuit Voltage Out Of Range |
GO to Pinpoint Test B |
| P0942:46 |
Hydraulic Pressure Unit: Calibration/Parameter Memory Failure |
GO to Pinpoint Test AL |
| P0942:49 |
Hydraulic Pressure Unit: Internal Electronic Failure |
GO to Pinpoint Test AL |
| P193B:00 |
Throttle/Pedal Signal: No Sub Type Information |
GO to Pinpoint Test AR |
| U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test AA |
| U0103:00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test H |
| U011D:00 |
Lost Communication With All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test AG |
| U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test AM |
| U0131:00 |
Lost Communication With Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test W |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test C |
| U0146:87 |
Lost Communication With Serial Data Gateway 'A': Missing Message |
GO to Pinpoint Test AC |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AQ |
| U0151:87 |
Lost Communication With Restraints Control Module: Missing Message |
GO to Pinpoint Test AQ |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AI |
| U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AN |
| U0265:00 |
Lost Communication with Image Processing Sensor 'A': No Sub Type Information |
GO to Pinpoint Test O |
| U0300:51 |
Internal Control Module Software Incompatibility: Not Programmed |
GO to Pinpoint Test S |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AA |
| U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test AA |
| U0404:86 |
Invalid Data Received from Gear Shift Control Module A: Signal Invalid |
GO to Pinpoint Test H |
| U0405:86 |
Invalid Data Received From Cruise Control Module: Signal Invalid |
GO to Pinpoint Test N |
| U0420:00 |
Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test W |
| U0420:83 |
Invalid Data Received from Power Steering Control Module 'A': Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test W |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test C |
| U0428:82 |
Invalid Data Received From Steering Angle Sensor Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test AM |
| U0428:83 |
Invalid Data Received From Steering Angle Sensor Module: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AM |
| U0429:82 |
Invalid Data Received From Steering Column Control Module: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test AO |
| U0429:86 |
Invalid Data Received From Steering Column Control Module: Signal Invalid |
GO to Pinpoint Test AO |
| U0452:29 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test AQ |
| U0452:83 |
Invalid Data Received From Restraints Control Module: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AQ |
| U0452:86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test AQ |
| U053B:82 |
Invalid Data Received From Image Processing Module A: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test O |
| U053B:83 |
Invalid Data Received From Image Processing Module A: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test O |
| U0557:86 |
Invalid Data Received From Front Controls Interface Module 'A': Signal Invalid |
GO to Pinpoint Test AN |
| U2001:00 |
Reduced System Function: No Sub Type Information |
GO to Pinpoint Test F |
| U2007:46 |
Valve(s): Calibration/Parameter Memory Failure |
GO to Pinpoint Test AL |
| U2007:62 |
Valve(s): Signal Compare Failure |
GO to Pinpoint Test AL |
| U2017:57 |
Control Module Software #2: Invalid/Incompatible Software Component |
GO to Pinpoint Test S |
| U2017:93 |
Control Module Software #2: No Operation |
GO to Pinpoint Test S |
| U2024:51 |
Control Module Cal-Config Data: Not Programmed |
GO to Pinpoint Test S |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test S |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test S |
| U2107:00 |
Collision Mitigation By Braking: No Sub Type Information |
GO to Pinpoint Test N |
| U2107:68 |
Collision Mitigation By Braking: Event Information |
GO to Pinpoint Test AH |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test S |
| U3000:47 |
Control Module: Watchdog/Safety μC Failure |
GO to Pinpoint Test R |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test R |
| U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test R |
| U3002:62 |
Vehicle Identification Number: Signal Compare Failure |
GO to Pinpoint Test X |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test E |
| U3003:1C |
Battery Voltage: Circuit Voltage Out Of Range |
GO to Pinpoint Test A |
| U300A:29 |
Ignition Switch: Signal Invalid |
GO to Pinpoint Test A |
| P0555:00 |
Brake Booster Pressure Sensor Circuit: No Sub Type Information |
GO to Pinpoint Test B |
| P0556:00 |
Brake Booster Pressure Sensor Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test B |
| P0557:00 |
Brake Booster Pressure Sensor Circuit Low: No Sub Type Information |
GO to Pinpoint Test B |
| P0558:00 |
Brake Booster Pressure Sensor Circuit High: No Sub Type Information |
GO to Pinpoint Test B |
| P0559:00 |
Brake Booster Pressure Sensor Circuit Intermittent: No Sub Type Information |
GO to Pinpoint Test B |
| P05FF:00 |
Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information |
GO to Pinpoint Test B |
| P103C:00 |
Aspirator Valve Control Circuit/Open: No Sub Type Information |
GO to Pinpoint Test AP |
| P103D:00 |
Aspirator Valve Control Circuit Low: No Sub Type Information |
GO to Pinpoint Test AP |
| P103E:00 |
Aspirator Valve Control Circuit High: No Sub Type Information |
GO to Pinpoint Test AP |