Common Specifications & Procedures

ESCAPE COMMON SPECIFICATIONS & PROCEDURES

	System		Specification/Procedure
Air Conditioning
Service			SPECIFICATIONS
Torque			Refer to appropriate procedure(s) in REMOVAL AND INSTALLATION .
Axle Nut/Hub Nut			Stage 1: 74 lb.ft (100 Nm) Stage 2: 60°
Battery			Refer to SPECIFICATIONS .
Brakes
Bleeding Sequence			Refer to the appropriate procedure GENERAL PROCEDURES .
Disc Brakes w/Torque
Front Disc 81 lb.ft (110 Nm)			Refer to appropriate component procedure in BRAKE DISC
Rear Disc 46 lb.ft (63 Nm)			Refer to appropriate component procedure in BRAKE DISC
Charging
Generator w/Torque
	1.5L EcoBoost (129kW/175PS) (CR)
		Generator Stud Bolt	35 lb.ft (47.5 Nm)
		Generator Bolt	35 lb.ft (47.5 Nm)
		B+ Wire Nut	155 lb.in (17.5 Nm)
	2.0L EcoBoost (184kW/250PS) - MI
		Generator Stud Bolt	35 lb.ft (47.5 Nm)
		Generator Bolt	35 lb.ft (47.5 Nm)
		B+ Wire Nut	155 lb.in (17.5 Nm)
Drive Belts
Adjustment
	1.5L EcoBoost (129kW/175PS) (CR)		ACCESSORY DRIVE BELT
	2.0L EcoBoost (184kW/250PS) - MI		ACCESSORY DRIVE BELT
Belt Routing
	1.5L EcoBoost (129kW/175PS) (CR)		ACCESSORY DRIVE - COMPONENT LOCATION
	2.0L EcoBoost (184kW/250PS) - MI		ACCESSORY DRIVE - COMPONENT LOCATION
Engine Cooling
General Service Specifications
	1.5L EcoBoost (129kW/175PS) (CR)		SPECIFICATIONS
	2.0L EcoBoost (184kW/250PS) - MI		SPECIFICATIONS
	2.5L Duratec - Hybrid (121kW/164PS) (BG)		SPECIFICATIONS
Radiator Pressure Cap			17.4 psi (120 kPa) to 21.8 psi (150 kPa)
Radiator Pressure Test (removed from vehicle)			20.0 psi (138 kPA)
Thermostat
	1.5L EcoBoost (129kW/175PS) (CR)		THERMOSTAT HOUSING
	2.0L EcoBoost (184kW/250PS) - MI		THERMOSTAT
	2.5L Duratec - Hybrid (121kW/164PS) (BG)		THERMOSTAT HOUSING
Water Pump
	1.5L EcoBoost (129kW/175PS) (CR)		COOLANT PUMP
	2.0L EcoBoost (184kW/250PS) - MI		COOLANT PUMP
	2.5L Duratec - Hybrid (121kW/164PS) (BG)		COOLANT PUMP
Engine Mechanical
1.5L EcoBoost (129kW/175PS) (CR)
Compression			SPECIFICATIONS
	Minimum oil pressure at ECT of 175.9°F (80°C) and an engine speed of 850 rpm		15 psi (1.035 bar)
Minimum oil pressure at an ECT of 175.9°F (80°C) and an engine speed of 2000 rpm			19.0 psi (1.31 bar)
Overhaul			SPECIFICATIONS
Torque			Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION .
2.0L EcoBoost (184kW/250PS) - MI
Compression			SPECIFICATIONS
	Oil pressure @ 1, 500 rpm with engine oil temperature between 121.9 -175.9 °F (50 -80 °C)		20.3-34.8 psi (140-240 kPa)
	Overhaul		SPECIFICATIONS
	Torque		Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION
2.5L Duratec - Hybrid (121kW/164PS) (BG)
	Compression		SPECIFICATIONS
	Oil pressure (hot @ 2000 rpm)		29-60 psi (200-414 kPa)
	Overhaul		SPECIFICATIONS
	Torque		Refer to appropriate component procedure(s) in REMOVAL AND INSTALLATION .
Fluid Specifications			See FLUIDS under MAINTENANCE tab.
Flywheel/Flex Plate Torque
1.5L EcoBoost (129kW/175PS) (CR) Tightening Sequence: Refer to FLEXPLATE .
	Stage 1		89 lb.in (10 Nm)
Stage 2			177 lb.in (20 Nm)
Stage 3			22 lb.ft (30 Nm)
Stage 4			90°
2.0L EcoBoost (184kW/250PS) - MI Tightening Sequence: Refer to FLEXPLATE .
	Stage 1		37 lb. ft (50 Nm)
Stage 2			59 lb. ft. (80 Nm)
Stage 3			83 lb. ft. (112 Nm)
2.5L Duratec - Hybrid (121kW/164PS) (BG) Tightening Sequence: Refer to FLYWHEEL .
	Stage 1		37 lb. ft (50 Nm)
Stage 2			59 lb. ft (80 Nm)
Stage 3			83 lb. ft (112 Nm)
Fuel System
Fuel Filter Location			Lifetime fuel filter (serviced as part of the Fuel Pump module).
Fuel Filter
	1.5L EcoBoost (129kW/175PS) (CR) Fuel Pump and Sender Unit Nuts: 80 lb.in (9 Nm)		FUEL PUMP AND SENDER UNIT
2.0L EcoBoost (184kW/250PS) - MI Fuel Pump and Sender Unit Nuts: 80 lb.in (9 Nm)			FUEL PUMP AND SENDER UNIT
2.5L Duratec - Hybrid (121kW/164PS) (BG) Fuel Pump and Sender Unit Nuts: 80 lb.in (9 Nm)			FUEL PUMP AND SENDER UNIT - FULL HYBRID ELECTRIC VEHICLE (FHEV)
Pressure Release Procedure
	1.5L EcoBoost (129kW/175PS) (CR)		FUEL SYSTEM PRESSURE RELEASE
2.0L EcoBoost (184kW/250PS) - MI			FUEL SYSTEM PRESSURE RELEASE
2.5L Duratec - Hybrid (121kW/164PS) (BG)			FUEL SYSTEM PRESSURE RELEASE
Pressure Specification
	1.5L EcoBoost (129kW/175PS) (CR)		50.8 -87.7 psi (350 -605 kPa)
2.0L EcoBoost (184kW/250PS) - MI			50.8 -87.7 psi (350 -605 kPa)
2.5L Duratec - Hybrid (121kW/164PS) (BG)			50.8-62.1psi (350-428kPa)
Fuel Pressure Test Procedure
	1.5L EcoBoost (129kW/175PS) (CR)		FUEL SYSTEM PRESSURE CHECK
2.0L EcoBoost (184kW/250PS) - MI			FUEL SYSTEM PRESSURE CHECK
2.5L Duratec - Hybrid (121kW/164PS) (BG)			FUEL SYSTEM PRESSURE CHECK
Ignition
Firing Order & Cylinder Identification			Refer to FIRING ORDER & CYLINDER IDENTIFICATION
Spark Plugs
1.5L EcoBoost (129kW/175PS) (CR)
	Number		JYSP-12Y-PTX
Gap			0.65-0.75 mm
Torque			177 lb.in (20 Nm)
2.0L EcoBoost (184kW/250PS) - MI
	Number		JYSP-12Y-PTX
Gap			0.65-0.75 mm
Torque			177 lb.in (20 Nm)
2.5L Duratec - Hybrid (121kW/164PS) (BG)
	Number		AYFS-32Y-RX
	Gap		0.051 in (1.3 mm)
	Torque		106 lb.in (12 Nm)
Starter
		1.5L EcoBoost (129kW/175PS) (CR)
	Starter Motor Bracket Nuts		97 lb.in (11 Nm)
	Starter Motor Studs		37 lb.ft (50 Nm)
	Starter Motor Battery Cable Nut		15 lb.in (13 Nm)
	Starter Motor Solenoid Wire Nut		62 lb.in (7 Nm)
2.0L EcoBoost (184kW/250PS) - MI
Starter Motor Bracket Nuts			97 lb.in (11 Nm)
Starter Motor Studs			47.5 Nm
	Starter Motor Battery Cable Nut		12 Nm
	Starter Motor Solenoid Wire Nut		6 Nm
Wheel Alignment
Adjustment Specifications			SPECIFICATIONS
Torque			Refer to the appropriate procedure in SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque			100 lb.ft (135 Nm)