| B1C03:23 |
Memory #1 Switch: Signal Stuck Low |
GO to Pinpoint Test I |
| B1C04:23 |
Memory #2 Switch: Signal Stuck Low |
GO to Pinpoint Test I |
| B1C05:23 |
Memory #3 Switch: Signal Stuck Low |
GO to Pinpoint Test I |
| B1151:4B |
Passenger Seat Cushion: Over Temperature |
GO to Pinpoint Test M |
| B1153:4B |
Driver Seat Cushion: Over Temperature |
GO to Pinpoint Test L |
| B1155:11 |
Passenger Seat: Circuit Short To Ground |
GO to Pinpoint Test M |
| B1155:12 |
Passenger Seat: Circuit Short To Battery |
GO to Pinpoint Test M |
| B1155:13 |
Passenger Seat: Circuit Open |
GO to Pinpoint Test M |
| B1155:1A |
Passenger Seat: Circuit Resistance Below Threshold |
GO to Pinpoint Test M |
| B1156:11 |
Driver Seat: Circuit Short To Ground |
GO to Pinpoint Test L |
| B1156:12 |
Driver Seat: Circuit Short To Battery |
GO to Pinpoint Test L |
| B1156:13 |
Driver Seat: Circuit Open |
GO to Pinpoint Test L |
| B1208:11 |
Driver Seat Cushion Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test L |
| B1208:2A |
Driver Seat Cushion Temperature Sensor: Signal Stuck In Range |
GO to Pinpoint Test L |
| B120A:11 |
Passenger Seat Cushion Temperature Sensor: Circuit Short To Ground |
GO to Pinpoint Test M |
| B120A:2A |
Passenger Seat Cushion Temperature Sensor: Signal Stuck In Range |
GO to Pinpoint Test M |
| B14BD:11 |
Driver Seat Cushion Blower: Circuit Short To Ground |
GO to Pinpoint Test O |
| B14BD:13 |
Driver Seat Cushion Blower: Circuit Open |
GO to Pinpoint Test O |
| B14C0:11 |
Passenger Seat Cushion Blower: Circuit Short To Ground |
GO to Pinpoint Test P |
| B14C0:13 |
Passenger Seat Cushion Blower: Circuit Open |
GO to Pinpoint Test P |
| B14C3:24 |
Seat Height Rear Down Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B14C4:24 |
Seat Height Rear Up Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B14CE:11 |
Seat Horizontal Motor Output: Circuit Short To Ground |
GO to Pinpoint Test H |
| B14CE:12 |
Seat Horizontal Motor Output: Circuit Short To Battery |
GO to Pinpoint Test H |
| B14CE:13 |
Seat Horizontal Motor Output: Circuit Open |
GO to Pinpoint Test H |
| B14CF:11 |
Seat Recline Motor Output: Circuit Short To Ground |
GO to Pinpoint Test H |
| B14CF:12 |
Seat Recline Motor Output: Circuit Short To Battery |
GO to Pinpoint Test H |
| B14CF:13 |
Seat Recline Motor Output: Circuit Open |
GO to Pinpoint Test H |
| B14D0:11 |
Seat Height Front/Tilt Motor Output: Circuit Short To Ground |
GO to Pinpoint Test H |
| B14D0:12 |
Seat Height Front/Tilt Motor Output: Circuit Short To Battery |
GO to Pinpoint Test H |
| B14D0:13 |
Seat Height Front/Tilt Motor Output: Circuit Open |
GO to Pinpoint Test H |
| B14D2:11 |
Seat Height Rear Motor Output: Circuit Short To Ground |
GO to Pinpoint Test H |
| B14D2:12 |
Seat Height Rear Motor Output: Circuit Short To Battery |
GO to Pinpoint Test H |
| B14D2:13 |
Seat Height Rear Motor Output: Circuit Open |
GO to Pinpoint Test H |
| B1562:11 |
Driver Seat Back Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test O |
| B1562:12 |
Driver Seat Back Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test O |
| B1563:11 |
Passenger Seat Back Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test P |
| B1563:12 |
Passenger Seat Back Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test P |
| B1564:11 |
Driver Seat Cushion Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test O |
| B1564:12 |
Driver Seat Cushion Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test O |
| B1565:11 |
Passenger Seat Cushion Blower Speed: Circuit Short To Ground |
GO to Pinpoint Test P |
| B1565:12 |
Passenger Seat Cushion Blower Speed: Circuit Short To Battery |
GO to Pinpoint Test P |
| B1B87:11 |
Seat Height Motor Speed/Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| B1B87:15 |
Seat Height Motor Speed/Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| B1B89:11 |
Seat Slide Motor Speed/Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| B1B89:15 |
Seat Slide Motor Speed/Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| B1B91:11 |
Seat Tilt Motor Speed/Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| B1B91:15 |
Seat Tilt Motor Speed/Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| B1B93:11 |
Seat Recline Motor Speed/Position Sensor: Circuit Short To Ground |
GO to Pinpoint Test I |
| B1B93:15 |
Seat Recline Motor Speed/Position Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test I |
| B1B96:24 |
Seat Slide Forward Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B1B97:24 |
Seat Slide Backward Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B1B98:24 |
Seat Tilt Up Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B1B99:24 |
Seat Tilt Down Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B1C00:24 |
Seat Recline Up Switch: Signal Stuck High |
GO to Pinpoint Test H |
| B1C01:24 |
Seat Recline Down Switch: Signal Stuck High |
GO to Pinpoint Test H |
| U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Q |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test R |
| U0199:00 |
Lost Communication With 'Door Control Module A': No Sub Type Information |
GO to Pinpoint Test Z |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AA |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AG |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AH |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AI |
| U3500:17 |
Control Module Input Power 'A' Circuit Range/Performance: Circuit Voltage Above Threshold |
GO to Pinpoint Test AC |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AG |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AH |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AI |
| B146F:00 |
Back Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test F |
| B146F:04 |
Back Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test F |
| B1470:00 |
Cushion Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test F |
| B1470:04 |
Cushion Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test F |
| B1471:11 |
Multi-Contour Seat Switch Input: Circuit Short To Ground |
GO to Pinpoint Test F |
| B1471:13 |
Multi-Contour Seat Switch Input: Circuit Open |
GO to Pinpoint Test F |
| B1471:2A |
Multi-Contour Seat Switch Input: Signal Stuck In Range |
GO to Pinpoint Test AJ |
| B1473:11 |
Pump Driver: Circuit Short To Ground |
GO to Pinpoint Test F |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test T |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0455:00 |
Invalid Data Received From Restraints Occupant Classification System Module 'A': No Sub Type Information |
GO to Pinpoint Test X |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AG |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AH |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AI |
| B146F:00 |
Back Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test G |
| B146F:04 |
Back Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test G |
| B1470:00 |
Cushion Bladder System Electropneumatic Failure: No Sub Type Information |
GO to Pinpoint Test G |
| B1470:04 |
Cushion Bladder System Electropneumatic Failure: System Internal Failure |
GO to Pinpoint Test G |
| B1471:11 |
Multi-Contour Seat Switch Input: Circuit Short To Ground |
GO to Pinpoint Test G |
| B1471:13 |
Multi-Contour Seat Switch Input: Circuit Open |
GO to Pinpoint Test G |
| B1471:2A |
Multi-Contour Seat Switch Input: Signal Stuck In Range |
GO to Pinpoint Test AJ |
| B1473:11 |
Pump Driver: Circuit Short To Ground |
GO to Pinpoint Test G |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test S |
| U0208:00 |
Lost Communication With Seat Control Module 'A': No Sub Type Information |
GO to Pinpoint Test T |
| U024B:00 |
Lost Communication with Seat Control Module 'G': No Sub Type Information |
GO to Pinpoint Test U |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0455:00 |
Invalid Data Received From Restraints Occupant Classification System Module 'A': No Sub Type Information |
GO to Pinpoint Test X |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test AG |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AH |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AI |