EVAP System Pressure Tester Improvement (SS002-00)
Publication date: 2000-10-06Reference number: SS002-00
EVAP SYSTEM PRESSURE TESTER IMPROVEMENT
TECHNICAL SERVICE BULLETIN
| COPYRIGHT: | © 2018 Lexus, a division of Toyota Motor Sales, USA License Agreement TMS1002 |
EVAP SYSTEM PRESSURE TESTER IMPROVEMENT
Model(s): All Lexus 2000 Models
Section: Special Service Tools
Bulletin No.: SS002-00
Date: October 6, 2000
INTRODUCTION
In an effort to expand the diagnostic capabilities of the EVAP System Pressure Tester and prevent inadvertent misuse of the tester pressure pump, the EVAP System Pressure Tester Kit, P/N 00002-6872A has been upgraded with the following components:
- New EVAP Lid Instructions
- Pump Outlet Hose Tie Wrap
- EVAP Brass Adapter
The information contained in this bulletin will provide you with a detailed outline for the procedures to upgrade the EVAP System Pressure Tester Kit.
APPLICABLE VEHICLES
2000 model year Lexus vehicles, all models.
PARTS INFORMATION
| Previous Part Number | Current Part Number | Part Name |
|---|---|---|
| N/A | 0002-6872A-DEC | EVAP System Tester Kit Lid Instructions Decal |
| N/A | 0002-6872A-TIE | Pump Outlet Hose Tie Wrap |
| N/A | 0002-6872A-ADP | EVAP Brass Adaptor |
REQUIRED TOOLS & MATERIALS
| Tools & Materials | Quantity |
|---|---|
| Side Cutting Pliers | 1 |
WARRANTY INFORMATION
| OpCode | Description | Time | OPN | T1 | T2 |
|---|---|---|---|---|---|
| N/A | Not Applicable to Lexus Warranty | --- | --- | -- | -- |
APPLICABLE WARRANTY:
With the LIFETIME MARATHON(TM) WARRANTY, all SPX OTC products and parts are warranted against defects in materials and workmanship for the life of the product or part. For service on this or any other Lexus SST, call 1 (800) 933 335.
PART UPGRADE DESCRIPTION
EVAP SYSTEM TESTER KIT LID INSTRUCTIONS DECAL
This decal will replace the existing decal that is located on the inside lid of the EVAP tester case. The revised decal will provide a new diagram with a clear layout for hooking up the new EVAP brass adapter, as well as a revised diagram for hook-up of the gas cap tester.
PUMP OUTLET HOSE TIE WRAP
The tie wrap will be used to secure the pump outlet hose that is located on the air pump of the EVAP System Tester Kit. The pump outlet hose must be secured with a tie wrap to discourage improper hose removal/attachment.
EVAP BRASS ADAPTER
The new EVAP brass adapter will enable technicians to perform enhanced pinpoint testing. This brass adapter is a multi-sized hose fitting that can adapt to various sized hoses and will simply screw directly onto the threaded end of the tester hose.
REPLACEMENT PROCEDURE
EVAP LID INSTRUCTIONS
- Remove the old EVAP System Tester Lid Instruction Decal completely.
- Make sure that the application area is clean of debris and dry.
- Place the new EVAP System Tester Lid Instruction Decal (P/N 00002 872A-DEC) where the previous decal was located.
PUMP OUTLET HOSE TIE WRAP INSTALLATION
- Place the pump outlet hose tie wrap (P/N 00002 872A-TIE) around the pump outlet hose. See Fig 1.
- Tighten the tie wrap until the hose is secure and cannot be removed.
- Trim the excess tie wrap length using a pair of side cutting pliers.
COMPONENT APPLICATION
EVAP BRASS ADAPTER
Refer to Fig 2 for proper hook-up of the EVAP brass adapter.
FUEL TANK ADAPTER
Refer to Fig 3 for proper hook-up of the fuel tank adapter.
FUEL CAP ADAPTER
Refer to Fig 4, proper hook-up of the fuel cap adapter.