Torque Specification
STEERING COMPONENTS TIGHTENING TORQUE SPECIFICATIONS
| Part tightened, (1) | N.m | kgf.cm | ft.lbf | |||
|---|---|---|---|---|---|---|
| STEERING COLUMN | ||||||
| Steering wheel pad set screw (Torx screw) | 8.8 | 90 | 78 in.lbf | |||
| Steering wheel set nut | 50 | 510 | 37 | |||
| Intermediate shaft assembly x Control valve shaft | 35 | 360 | 26 | |||
| No.2 intermediate shaft assembly x Intermediate shaft assembly | 35 | 360 | 26 | |||
| Column assembly set nut | 25 | 260 | 19 | |||
| No.2 intermediate shaft assembly x Main shaft | 35 | 360 | 26 | |||
| Column tube support set bolt | 20 | 200 | 15 | |||
| Tilt slider assembly set bolt | 23 | 230 | 17 | |||
| POWER STEERING VANE PUMP 2JZ-GE ENGINE: |
||||||
| Union bolt | 49 | 500 | 36 | |||
| Pump assembly set bolt | 58 | 590 | 43 | |||
| Vane pump pulley set nut | 43 | 440 | 32 | |||
| Front housing x Rear housing | 24 | 240 | 17 | |||
| Oil reservoir set bolt | Front | 13 | 130 | 9 | ||
| Rear | 24 | 240 | 17 | |||
| Solenoid valve x Front housing | 51 (69) | 520 (700) | 38(51) | |||
| POWER STEERING VANE PUMP 3UZ-FE ENGINE: |
||||||
| Union bolt | 49 | 500 | 36 | |||
| Pump assembly set bolt | 39 | 400 | 29 | |||
| Pump assembly set nut | 43 | 440 | 32 | |||
| Vane pump pulley set nut | 43 | 440 | 32 | |||
| Front housing x Rear bracket | 39 | 400 | 29 | |||
| Suction port union set bolt | 13 | 130 | 9 | |||
| Air control valve | 29 | 300 | 22 | |||
| Solenoid valve x Front housing | 51 (69) | 520 (700) | 38(51) | |||
| POWER STEERING GEAR | ||||||
| Intermediate shaft assembly x Control valve shaft | 35 | 360 | 26 | |||
| Pressure feed and return tube set union bolt | 49 | 500 | 36 | |||
| PS gear assembly set bolt | 65 | 660 | 48 | |||
| Tube clamp set bolt | 5.0 | 55 | 48 in..lbf | |||
| Turn pressure tube, with SST | 23 (25) | 240 (250) | 17 (18) | |||
| Turn pressure tube, ( ): For use without SST | (25) | (250) | (18) | |||
| Tie rod end Lock nut | 56 | 570 | 41 | |||
| Rack end x Steering rack, with SST | 76 (103) | 770 (1,050) | 56 (76) | |||
| Rack end x Steering rack, ( ): For use without SST | (103) | (1,050) | (76) | |||
| Rack guide spring cap lock nut, with SST | 51 (69) | 520 (700) | 38 (51) | |||
| Rack guide spring cap lock nut, ( ): For use without SST | (69) | (700) | (51) | |||
| Control valve assembly set bolt | 18 | 180 | 13 | |||
| Bearing guide nut | 25 | 250 | 18 | |||
| Cylinder end stopper | 59 | 600 | 43 | |||
|
||||||