Torque Specification
WARNING: This page is about a different car, the 2005 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
1GR-FE:
TORQUE SPECIFICATION - 1GR-FE
| Part Tightened | N.m | kgf.cm | ft.lbf |
|---|---|---|---|
| Starter assy x Transmission housing | 37 | 377 | 27 |
| Starter assy x Terminal 30 | 9.8 | 100 | 7 |
| Starter commutator end frame assy x Starter drive housing assy (Starter Assy 1.6kW) | 60 | 61 | 53 in.lbf |
| Starter drive housing assy x Repair service starter kit (Starter Assy 1.6 kW) | 7.5 | 76 | 66 in.lbf |
| Lead wire x Repair service starter kit (Starter Assy 1.6 kW) | 10 | 102 | 7.4 |
| Commutator end frame x Brush holder (Starter Assy 2.0 kW) | 3.8 | 39 | 34 in.lbf |
| Starter drive housing assy x Magnetic Starter Switch (Starter Assy 2.0 kW) | 9.3 | 95 | 82 in.lbf |
| Commutator end frame x Starter drive housing assy (Starter Assy 2.0 kW) | 9.3 | 95 | 82 in.lbf |
| Lead wire x Terminal C of starter (Starter Assy 2.0 kW) | 5.9 | 60 | 52 in.lbf |
| Engine wire x Cylinder block | 13 | 133 | 10 |
| Manifold stay x Transmission housing and Exhaust manifold | 40 | 408 | 30 |
| Steering sliding yoke x Steering intermediate shaft No.2 | 36 | 370 | 27 |
| Generator assy x V-ribbed belt tensioner and cylinder head | 43 | 438 | 32 |
| Generator assy x Wire harness clamp bracket | 8.0 | 82 | 71 in.lbf |
| Generator assy x Terminal B | 9.8 | 100 | 7 |
| Wire harness stay x Body | 8.0 | 82 | 71 in.lbf |
| V-bank cover x Intake air surge tank sub-assy and Air cleaner assy | 7.5 | 76 | 66 in.lbf |
| Engine under cover sub-assy No. 1 x Frame assy | 29 | 296 | 21 |
| Engine under cover assy rear x Frame assy | 29 | 296 | 21 |
| Retainer plate x Drive end frame assy generator | 2.6 | 27 | 23 in.lbf |
| Generator coil assy x Drive frame assy generator | 5.8 | 59 | 51 in.lbf |
| Generator brush holder assy x Generator coil assy | 1.8 | 18 | 16 in.lbf |
| Generator rear end cover x Generator coil assy | 4.6 | 47 | 41 in.lbf |
| Generator pulley x Generator rotor assy | 110 | 1,122 | 81 |
2UZ-FE:
TORQUE SPECIFICATION - 2UZ-FE
| Part Tightened | N.m | kgf.cm | ft.lbf |
|---|---|---|---|
| End cover x Brush holder 1.4 kW type | 1.5 | 15 | 13 in.lbf |
| End cover x Brush holder 2.0 kW type | 3.8 | 39 | 34 in.lbf |
| Starter hosing x Magnetic switch 1.4 kW type | 5.9 | 60 | 52 in.lbf |
| Starter hosing x Magnetic switch 2.0 kW type | 9.3 | 95 | 82 in.lbf |
| End cover with field frame x Magnetic switch 1.4 kW type | 5.9 | 60 | 52 in.lbf |
| End cover with field frame x Magnetic switch 2.0 kW type | 9.3 | 95 | 82 in.lbf |
| Lead wire of field coil x Terminal C | 5.9 | 60 | 52 in.lbf |
| Wire clamp, Starter wire x Starter | 9.8 | 100 | 86 in.lbf |
| Starter x Cylinder block | 39 | 400 | 29 |
| Water by-pass joint RR x Cylinder head | 18 | 185 | 13 |
| Water by-pass pipe x Water pump | 18 | 185 | 13 |
| Intake manifold x Cylinder head Bolt | 18 | 185 | 13 |
| Intake manifold x Cylinder head Nut | 18 | 185 | 13 |
| Bearing retainer x Drive end frame | 2.6 | 2.7 | 23 in.lbf |
| Rectifier end frame x Drive end frame | 5.8 | 59 | 51 in.lbf |
| Generator pulley x Rotor | 110.5 | 1,125 | 81 |
| Brush holder x Rectifier holder, Voltage regulator | 1.8 | 18 | 16 in.lbf |
| Rear end cover x Rectifier holder | 4.6 | 47 | 41 in.lbf |
| Generator x Cylinder block Bolt | 39 | 400 | 29 |
| Generator x Cylinder block Nut (M10) | 39 | 400 | 29 |
| Generator x Cylinder block Nut (M8) | 16 | 158 | 11 |
| Generator wire x Generator | 9.8 | 100 | 86 |
| Fan shroud x Radiator | 5.0 | 51 | 44 in.lbf |
| Fluid coupling x Engine | 29 | 296 | 21 |