Service Data

Service Data (1 Of 4)

Cold tire inflation pressure

Tire size

275/60R18

Front

200 kPa (2.0 kgf/cm² , 29 psi)
⁽¹⁾220 kPa (2.2 kgf/cm² , 32 psi)

Rear

220 kPa (2.2 kgf/cm² , 32 psi)
⁽¹⁾240 kPa (2.4 kgf/cm² , 35 psi)

Front wheel alignment

Vehicle height

Front

A - B

82.7 mm (3.256 in.)

Rear

C - D

71.2 mm (2.803 in.)

Camber

0°00' ± 45' (0° ± 0.75°)

Left-right error

30' (0.5°) or less

Caster

3°05' ± 45' (3.08° ± 0.75°)

Left-right error

30' (0.5°) or less

Steering axis inclination

12°15' ± 45' (12.25° ± 0.75°)

Left-right error

30' (0.5°) or less

Toe-in (total)

0°00' ± 12' (0° ± 0.2°, 0 ± 2 mm, 0 ± 0.08 in.)

Rack end length difference

3.0 mm (0.118 in.) or less

Wheel angle

Inside wheel

36°42' (33°42' - 36°42')
36.7° (33.7° - 36.7°)

Outside wheel: Reference

32°36'
32.6°

Front axle

Front axle hub preload (at starting)

42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)

Snap ring thickness

1.8 mm (0.0709 in.)
2.0 mm (0.0787 in.)
2.2 mm (0.0866 in.)
2.4 mm (0.0945 in.)
2.6 mm (0.1024 in.)
2.8 mm (0.1102 in.)

Front drive shaft

Front drive shaft length

573.9 ± 5 mm (22.594 ± 0.197 in.)

Front suspension

Upper suspension arm ball joint turning torque

1.0 - 4.4 N.m (10 - 45 kgf.cm, 8.7 - 39 in.lbf)

Lower suspension arm ball joint turning torque

0.29 - 2.94 N.m (3 - 30 kgf.cm, 2.6 - 26 in.lbf)

Rear axle shaft

Bearing backlash

Max.

0.6 mm (0.024 in.)

Axle shaft deviation

Max.

0.05 mm (0.0020 in.)

Axle shaft runout

Max.

2.0 mm (0.079 in.)

Axle shaft flange runout

Max.

0.05 mm (0.0020 in.)

⁽¹⁾	Trailer towing

A: Ground clearance of spindle center
B: Ground clearance of lower suspension arm front bolt center
C: Ground clearance of rear axle shaft center
D: Ground clearance of lower control arm front bolt center

Service Data (2 Of 4)

Front differential	Companion flange vertical runout	Max.	0.14 mm (0.0055 in.)
	Companion flange lateral runout	Max.	0.14 mm (0.0055 in.)
	Drive pinion preload (at starting)	New bearing	1.1 - 1.6 N.m (11 - 16 kgf.cm, 9.7 - 13.9 in.lbf)
		Reused bearing	0.6 - 0.9 N.m (6 - 9 kgf.cm, 5.3 - 8.0 in.lbf)
	Total preload (at starting)		Drive pinion preload plus 0.4 - 0.6 N.m (4 - 6 kgf.cm, 3.5 - 5.2 in.lbf)
	Ring gear runout		0.07 mm (0.0028 in.)
	Ring gear backlash		0.13 - 0.18 mm (0.0051 - 0.0071 in.)
	Side gear backlash		0.05 - 0.20 mm (0.0020 - 0.0079 in.)
	Side gear thrust washer thickness		0.9 mm (0.035 in.) 1.0 mm (0.039 in.) 1.1 mm (0.043 in.) 1.2 mm (0.047 in.) 1.3 mm (0.051 in.)

Service Data (3 Of 4)

Front differential	Side bearing adjusting washer thickness	2.58 mm (0.1016 in.) 2.60 mm (0.1024 in.) 2.62 mm (0.1031 in.) 2.64 mm (0.1039 in.) 2.66 mm (0.1047 in.) 2.68 mm (0.1055 in.) 2.70 mm (0.1063 in.) 2.72 mm (0.1071 in.) 2.74 mm (0.1079 in.) 2.76 mm (0.1087 in.) 2.78 mm (0.1094 in.) 2.80 mm (0.1102 in.) 2.82 mm (0.1110 in.) 2.84 mm (0.1118 in.) 2.86 mm (0.1126 in.) 2.88 mm (0.1134 in.) 2.90 mm (0.1142 in.) 2.92 mm (0.1150 in.) 2.94 mm (0.1157 in.) 2.96 mm (0.1165 in.) 2.98 mm (0.1173 in.) 3.00 mm (0.1181 in.) 3.02 mm (0.1189 in.) 3.04 mm (0.1197 in.) 3.06 mm (0.1205 in.) 3.08 mm (0.1213 in.) 3.10 mm (0.1220 in.) 3.12 mm (0.1228 in.) 3.14 mm (0.1236 in.) 3.16 mm (0.1244 in.) 3.18 mm (0.1252 in.) 3.20 mm (0.1260 in.) 3.22 mm (0.1268 in.) 3.24 mm (0.1276 in.) 3.26 mm (0.1283 in.) 3.28 mm (0.1291 in.) 3.30 mm (0.1299 in.) 3.32 mm (0.1307 in.) 3.34 mm (0.1315 in.) 3.36 mm (0.1323 in.) 3.38 mm (0.1331 in.) 3.40 mm (0.1339 in.) 3.42 mm (0.1346 in.) 3.44 mm (0.1354 in.) 3.46 mm (0.1362 in.) 3.48 mm (0.1370 in.)
Front differential	Drive pinion bearing adjusting washer thickness	1.70 mm (0.0669 in.) 1.73 mm (0.0681 in.) 1.76 mm (0.0693 in.) 1.79 mm (0.0704 in.) 1.82 mm (0.0717 in.) 1.85 mm (0.0729 in.) 1.88 mm (0.0740 in.) 1.91 mm (0.0752 in.) 1.94 mm (0.0764 in.) 1.97 mm (0.0776 in.) 2.00 mm (0.0787 in.) 2.03 mm (0.0799 in.) 2.06 mm (0.0811 in.) 2.09 mm (0.0822 in.) 2.12 mm (0.0835 in.) 2.15 mm (0.0847 in.) 2.18 mm (0.0858 in.) 2.21 mm (0.0870 in.) 2.24 mm (0.0882 in.) 2.27 mm (0.0894 in.) 2.30 mm (0.0906 in.) 2.33 mm (0.0918 in.)

Service Data (4 Of 4)

Rear differential	Companion flange vertical runout	Max.	0.14 mm (0.0055 in.)
	Companion flange lateral runout	Max.	0.14 mm (0.0055 in.)
	Drive pinion preload (at starting)	New bearing	1.36 - 1.90 N.m (13.9 - 19.4 kgf.cm, 12.0 - 16.8 in.lbf)
	Drive pinion preload (at starting)	Reused bearing	0.71 - 0.99 N.m (7.2 - 10.1 kgf.cm, 6.3 - 8.8 in.lbf)
	Total preload (at starting)		Drive pinion preload plus 0.38 - 0.63 N.m (3.9 - 6.5 kgf.cm, 3.4 - 5.6 in.lbf)
	Ring gear runout	Max.	0.05 mm (0.0020 in.)
	Ring gear backlash		0.13 - 0.18 mm (0.0051 - 0.0071 in.)
	Side gear backlash		0.02 - 0.15 mm (0.0008 - 0.0059 in.)
	Differential case runout	Max.	0.04 mm (0.0016 in.)
	Side gear thrust washer thickness		1.55 mm (0.0610 in.) 1.60 mm (0.0630 in.) 1.65 mm (0.0650 in.) 1.70 mm (0.0669 in.) 1.75 mm (0.0689 in.) 1.80 mm (0.0709 in.) 1.85 mm (0.0728 in.) 1.90 mm (0.0748 in.) 1.95 mm (0.0768 in.) 2.00 mm (0.0787 in.) 2.05 mm (0.0807 in.) 2.10 mm (0.0827 in.)
	Tooth contact pattern adjusting washer thickness		1.050 mm (0.04134 in.) 1.075 mm (0.04232 in.) 1.100 mm (0.04331 in.) 1.125 mm (0.04429 in.) 1.150 mm (0.04528 in.) 1.175 mm (0.04626 in.) 1.200 mm (0.04724 in.) 1.225 mm (0.04823 in.) 1.250 mm (0.04921 in.) 1.275 mm (0.05020 in.) 1.300 mm (0.05118 in.) 1.325 mm (0.05217 in.) 1.350 mm (0.05315 in.) 1.375 mm (0.05413 in.) 1.400 mm (0.05512 in.) 1.425 mm (0.05610 in.) 1.450 mm (0.05709 in.) 1.475 mm (0.05807 in.) 1.500 mm (0.05906 in.) 1.525 mm (0.06004 in.) 1.550 mm (0.06102 in.)