Service Data
WARNING: This page is about a different car, the 2005 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
Differential Service
| Rear differential | Carrier oil seal drive in depth | 2.0 ± 0.3 mm (0.079 ± 0.012 in.) | |
| Side gear shaft oil seal drive in depth | 0 ± 0.5 mm (0 ± 0.019 in.) | ||
| Companion flange vertical runout | 0.10 mm (0.0039 in.) or less | ||
| Companion flange horizontal runout | 0.10 mm (0.0039 In.) or less | ||
| Ring gear runout | 0.07 mm (0.0028 in.) or less | ||
| Side gear backlash | 0.05 -- 0.20 mm (0.0020 -- 0.0079 in.) | ||
| Drive pinion to ring gear backlash | 0.13 -- 0.18 mm (0.0051 -- 0.0071 in.) | ||
| Drive pinion preload (at starting) | New bearing | 1.1 -- 1.7 N.m (11 - 17 kgf.cm, 9.6 -- 14.8 in..lbf) | |
| Reused bearing | 0.6 -- 0.9 N.m (6--9 kgf.cm, 5.2 -- 7.8 in..lbf) | ||
| Total preload (Drive pinion preload plus) | 0.3 -- 0.5 Nm (3 -- 5 kgf.cm, 2.6 -- 4.3 in..lbf) | ||
| Right and left side gear shafts standard distance | 242 mm (9.528 in.) | ||
| Side gear thrust washer thickness | mm (in.) | 0.93 -- 0.97 (0.0366 -- 0.0382) | |
| 0.98 -- 1.02 (0.0386 -- 0.0402) | |||
| 1.03 -- 1.07 (0.0406 -- 0.0421) | |||
| 1.08 -- 1.12 (0.0425 -- 0.0441) | |||
| 1.13 -- 1.17 (0.0445 -- 0.0461) | |||
| 1.18 -- 1.22 (0.0465 -- 0.0480) | |||
| 1.23 -- 1.27 (0.0484 -- 0.0500) | |||
| 1.28 -- 1.32 (0.0504 -- 0.0520) | |||
| 1.33 -- 1.37 (0.0524 -- 0.0539) | |||
| 1.38 -- 1.42 (0.0543 -- 0.0559) | |||
| Drive pinion plate washer thickness | mm (in.) | 2.26 -- 2.28 (0.0890 -- 0.0898) | |
| 2.29 -- 2.31 (0.0902 -- 0.0909) | |||
| 2.32 -- 2.34 (0.0913 -- 0.0921) | |||
| 2.35 -- 2.37 (0.0925 -- 0.0933) | |||
| 2.38 -- 2.40 (0.0937 -- 0.0945) | |||
| 2.41 -- 2.43 (0.0949 -- 0.0957) | |||
| 2.44 -- 2.46 (0.0961 -- 0.0969) | |||
| 2.47 -- 2.49 (0.0972 -- 0.0980) | |||
| 2.50 -- 2.52 (0.0984 -- 0.0992) | |||
| 2.53 -- 2.55 (0.0996 -- 0.1004) | |||
| 2.56 -- 2.58 (0.1008 -- 0.1016) | |||
| 2.59 -- 2.61 (0.1020 -- 0.1028) | |||
| 2.62 -- 2.64 (0.1031 -- 0.1039) | |||
| 2.65 -- 2.67 (0.1043 -- 0.1051) | |||
| 2.68 -- 2.70 (0.1055 -- 0.1063) | |||
| Rear differential | Side gear shaft plate washer thickness | mm (in.) | 2.21 -- 2.23 (0.0870 -- 0.0878) |
| 2.24 -- 2.26 (0.0882 -- 0.0890) | |||
| 2.27 -- 2.29 (0.0894 -- 0.0902) | |||
| 2.30 -- 2.32 (0.0906 -- 0.0913) | |||
| 2.33 -- 2.35 (0.0917 -- 0.0925) | |||
| 2.36 -- 2.38 (0.0929 -- 0.0937) | |||
| 2.39 -- 2.41 (0.0941 -- 0.0949) | |||
| 2.42 -- 2.44 (0.0953 -- 0.0961) | |||
| 2.45 -- 2.47 (0.0965 -- 0.0972) | |||
| 2.48 -- 2.50 (0.0976 -- 0.0984) | |||
| 2.51 -- 2.53 (0.0988 -- 0.0996) | |||
| 2.54 --- 2.56 (0.1000 --- 0.1008) | |||
| 2.57 -- 2.59 (0.1012 -- 0.1020) | |||
| 2.60 -- 2.62 (0.1024 -- 0.1031) | |||
| 2.63 -- 2.65 (0.1035 -- 0.1043) | |||
| 2.66 -- 2.68 (0.1047 -- 0.1055) | |||
| 2.69 -- 2.71 (0.1059 -- 0.1067) | |||
| 2.72 -- 2.74 (0.1071 -- 0.1079) | |||
| 2.75 -- 2.77 (0.1083 -- 0.1091) | |||
| 2.78 -- 2.80 (0.1094 -- 0.1102) | |||
| 2.81 -- 2.83 (0.1106 -- 0.1114) | |||
| 2.84 -- 2.86 (0.1118 -- 0.1126) | |||
| 2.87 -- 2.89 (0.1130 -- 0.1138) | |||
| 2.90 -- 2.92 (0.1142 -- 0.1150) | |||
| 2.93 -- 2.95 (0.1154 -- 0.1161) | |||
| 2.96 -- 2.98 (0.1165 -- 0.1173) | |||
| 2.99 -- 3.01 (0.1177 -- 0.1185) | |||
| 3.02 -- 3.04 (0.1189 -- 0.1197) | |||
| 3.05 -- 3.07 (0.1201 -- 0.1209) | |||
| 3.08 -- 3.10 (0.1213 -- 0.1220) | |||
| 3.11 -- 3.13 (0.1224 -- 0.1232) | |||
| 3.14 -- 3.16 (0.1236 -- 0.1244) | |||
| 3.17 -- 3.19 (0.1248 -- 0.1256) | |||
| 3.20 -- 3.22 (0.1260 -- 0.1268) | |||