Torque Specification
WARNING: This page is about a different car, the 2005 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
Engine Mechanical Torque Specification
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Vane pump assy x Pump bracket | 44 | 449 | 32 | |
| Vane pump assy x Adjust strut | 44 | 449 | 32 | |
| Generator bracket No. 2 x Generator assy | 58 | 591 | 43 | |
| Fan belt adjusting slider x Generator assy | 18 | 184 | 13 | |
| Front wheel | 103 | 1,050 | 76 | |
| Cylinder head cover x Cylinder head | 8.0 | 80 | 71 in..lbf | |
| Engine wire harness x Cylinder head cover | 8.4 | 85 | 74 in..lbf | |
| Engine wire harness protector x Cylinder head cover | 8.4 | 85 | 74 in..lbf | |
| Ignition coil assy x Cylinder head cover | 8.0 | 80 | 71 in..lbf | |
| Intake air surge tank x Intake manifold | 28 | 286 | 21 | |
| Surge tank stay No. 2 x Intake air control valve assy | 20 | 199 | 14 | |
| Surge tank stay No. 2 x Cylinder head | 20 | 199 | 14 | |
| Surge tank stay No. 1 x Intake air surge tank | 20 | 199 | 14 | |
| Surge tank stay No. 1 x Cylinder head | 20 | 199 | 14 | |
| Engine hanger No. 1 x Intake air surge tank | 20 | 199 | 14 | |
| Engine hanger No. 1 x Cylinder head | 20 | 199 | 14 | |
| PS pressure tube x Engine hanger No. 1 | 7.8 | 80 | 69 in..lbf | |
| Emission control valve set x Emission control valve bracket | 8.0 | 82 | 71 in..lbf | |
| V-bank cover x Cylinder head cover | 7.9 | 81 | 70 in..lbf | |
| Engine hanger No. 2 x Cylinder head | 20 | 199 | 14 | |
| Engine oil pressure switch assy x Cylinder block | 15 | 153 | 11 | |
| Generator bracket No. 1 x Cylinder block | 58 | 591 | 43 | |
| Pump bracket x Cylinder head | 32 | 326 | 24 | |
| Engine mounting bracket RH x Cylinder block | 54 | 551 | 40 | |
| Manifold stay No. 2 x Cylinder block | 49 | 500 | 36 | |
| Drive shaft bearing bracket (2WD) x Cylinder block | 64 | 650 | 47 | |
| Engine mounting bracket RR (4WD) x Cylinder block | 64 | 653 | 47 | |
| Engine mounting insulator RH x Engine mounting bracket RH | 95 | 969 | 70 | |
| Engine mounting insulator LH x Automatic transaxle assy | 95 | 969 | 70 | |
| Engine mounting insulator FR x Engine mounting bracket FR | 87 | 887 | 64 | |
| Engine mounting insulator RR (4WD) x Engine mounting bracket RR | 75 | 765 | 55 | |
| Rack & pinion power steering gear assy (4WD) x Front frame assy | 70 | 714 | 52 | |
| Stabilizer bar front (4WD) x Front frame assy | 17 | 173 | 13 | |
| Adjust strut x Engine mounting bracket RH | 44 | 449 | 32 | |
| Frame side rail plate sub-assembly x Front frame assy | ||||
| (See REPLACEMENT) | Bolt A | 85 | 867 | 63 |
| Bolt B | 32 | 329 | 24 | |
| Nut | 32 | 329 | 24 | |
| Front suspension member brace rear x Front frame assy | ||||
| (See REPLACEMENT) | Bolt C | 85 | 867 | 63 |
| Bolt D | 32 | 329 | 24 | |
| Nut | 32 | 329 | 24 | |
| Camshaft sub-gear x Main gear | 5.4 | 55 | 48 in..lbf | |
| Engine rear oil seal retainer x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil pump assy x Cylinder block (See OVERHAUL) | Bolt A | 8.0 | 82 | 71 in..lbf |
| Bolt B | 20 | 199 | 14 | |
| Bolt C | 43 | 439 | 32 | |
| Crankshaft position sensor x Oil pump assy | 8.0 | 80 | 71 in..lbf | |
| Oil pan baffle plate x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan sub-assy x Cylinder block (See OVERHAUL) | 10 mm head | 8.0 | 82 | 71 in..lbf |
| 12 mm head | 20 | 199 | 14 | |
| Oil strainer sub-assy x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan sub-assy No. 2 x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan drain plug x Oil pan sub-assy No. 2 | 45 | 459 | 33 | |
| Water inlet housing x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Cylinder head x Cylinder block | 12 pointed head 1st | 54 | 550 | 40 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Recessed head | 19 | 189 | 14 | |
| Oil control valve filter x Cylinder head | 45 | 459 | 33 | |
| Cylinder head cover rear x Cylinder head | 10 | 102 | 7 | |
| Camshaft timing gear assy (VVT-i) x Camshaft | 150 | 1,530 | 111 | |
| Camshaft bearing cap x Cylinder head | 16 | 163 | 12 | |
| Timing belt plate x Oil pump assy | 8.0 | 82 | 71 in..lbf | |
| Water pump assy x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil level gage guide x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil filter union x Cylinder block | 30 | 306 | 22 | |
| Timing belt idler bracket x Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 3 cover x Cylinder head | 8.5 | 87 | 76 in..lbf | |
| Camshaft timing pulley x Camshaft | 125 | 1,275 | 92 | |
| Timing belt idler sub-assy No. 2 x Timing belt idler bracket | 43 | 438 | 32 | |
| Timing belt idler sub-assy No. 1 x Cylinder block | 34 | 347 | 25 | |
| Chain tensioner assy No. 1 x Oil pump assy | 27 | 280 | 20 | |
| Engine mounting bracket RH x Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 2 cover x Timing belt No. 3 cover | 8.5 | 87 | 75 in..lbf | |
| Timing belt No. 1 cover x OH pump assy | 8.5 | 87 | 75 in..lbf | |
| Crankshaft pulley x Crankshaft | 220 | 2,250 | 162 | |
| VVT sensor x Cylinder head | 8.0 | 82 | 71 in..lbf | |
| Camshaft timing oil control valve assy x Cylinder head | 8.0 | 82 | 71 in..lbf | |
| Spark plug x Cylinder head | 25 | 250 | 18 | |
| Generator bracket No. 2 x Engine mounting bracket RH | 28 | 286 | 21 | |
| Engine mounting stay No. 2 RH x Engine mounting bracket RH | 64 | 653 | 47 | |
| Engine moving control rod (See REPLACEMENT) | 12 mm head | 23 | 235 | 17 |
| 14 mm head | 64 | 653 | 47 | |
| Exhaust manifold sub-assy RH (2WD) x Cylinder head | 49 | 500 | 36 | |
| Exhaust manifold converter sub-assy (4WD) x Cylinder head | 49 | 500 | 36 | |
| Manifold stay x Exhaust manifold sub-assy RH (2WD) | 34 | 347 | 25 | |
| Manifold stay x Exhaust manifold converter sub-assy (4WD) | 34 | 347 | 25 | |
| Manifold stay x Automatic transaxle assy | 34 | 347 | 25 | |
| Exhaust manifold heat insulator No. 1 x Exhaust manifold sub-assy | ||||
| RH (2WD) | 8.5 | 87 | 75 in..lbf | |
| Exhaust manifold heat insulator No. 1 x Exhaust manifold converter | ||||
| sub-assy (4WD) | 8.5 | 87 | 75 in..lbf | |
| Water outlet x Cylinder head | 15 | 153 | 11 | |
| Intake manifold x Cylinder head | 15 | 153 | 11 | |
| Ground cable x Intake manifold | 8.4 | 86 | 74 in..lbf | |
| Wire harness clamp bracket x Cylinder head | 5.4 | 55 | 48 in..lbf | |
| Ground cable x Cylinder head | 5.4 | 55 | 48 in..lbf | |
| Exhaust manifold converter sub-assy No. 2 x Cylinder head | 49 | 500 | 36 | |
| Exhaust manifold heat insulator No. 2 x Exhaust manifold converter | ||||
| sub-assy No. 2 | 8.5 | 87 | 75 in..lbf | |
| Manifold converter insulator No. 3 x Exhaust manifold converter | ||||
| sub-assy No. 2 | 8.5 | 87 | 75 in..lbf | |
| Exhaust pipe assy FR x Exhaust manifold converter sub-assy No. 2 | 62 | 632 | 46 | |
| Drive plate & ring gear sub-assy | 83 | 846 | 61 | |
| W/head straight screw plug No. 1 x Cylinder head | 44 | 449 | 32 | |
| W/head straight screw plug No. 2 x Cylinder head | 44 | 449 | 32 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Main bearing cap x Cylinder block | 12 pointed head 1st | 22 | 224 | 16 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 6 pointed head | 27 | 275 | 20 | |
| Cylinder block w/head straight screw No. 1 plug x Cylinder block | 30 | 306 | 22 | |
| Cylinder block w/head straight screw No. 2 plug x Cylinder block | 30 | 306 | 22 | |
| Cylinder block w/head straight screw No. 3 plug x Cylinder block | 50 | 510 | 37 | |
| Water seal plate x Cylinder block | 18 | 184 | 13 | |
| Cylinder block water drain cock sub-assy x Cylinder block | 39 | 398 | 29 | |