Data List / Active Test

HINT:

With the intelligent tester connected to the DLC3 and the ignition switch in the ON position, the ABS, TRAC and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.

ACTIVE TEST REFERENCE CHART

Item

Measurement Item / Range (Display)

Normal Condition

Diagnostic Note

ABS MOT RELAY

ABS motor relay / ON or OFF

ON: Motor relay ON

SOL RELAY

Solenoid relay / ON or OFF

ON: Solenoid relay ON

VSC / TRC OFF SW⁽¹⁾

TRAC control switch / ON or OFF

ON: TRAC control switch ON

IDLE SW

Main idle switch / ON or OFF

ON: Accelerator pedal released
OFF: Accelerator pedal depressed

STOP LIGHT SW

Stop light switch / ON or OFF

ON: Brake pedal depressed
OFF: Brake pedal released

PKB SW

Parking brake switch / ON or OFF

ON: Parking brake applied
OFF: Parking brake released

ABS OPERT FR

ABS operation (FR) / BEFORE or OPERATE

BEFORE: No ABS operation (FR)
OPERATE: During ABS operation (FR)

ABS OPERT FL

ABS operation (FL) / BEFORE or OPERATE

BEFORE: No ABS operation (FL)
OPERATE: During ABS operation (FL)

ABS OPERT RR

ABS operation (RR) / BEFORE or OPERATE

BEFORE: No ABS operation (RR)
OPERATE: During ABS operation (RR)

ABS OPERT RL

ABS operation (RL) / BEFORE or OPERATE

BEFORE: No ABS operation (RL)
OPERATE: During ABS operation (RL)

WHEEL SPD FR

Wheel speed sensor (FR) reading / min.: 0 km/h (0 MPH, max.: 326 km/h (202 MPH)

Actual wheel speed

Similar speed as indicated on speed meter

WHEEL SPD FL

Wheel speed sensor (FL) reading / min.: 0 km/h (0 MPH, max.: 326 km/h (202 MPH)

Actual wheel speed

Similar speed as indicated on speed meter

WHEEL SPD RR

Wheel speed sensor (RR) reading / min.: 0 km/h (0 MPH, max.: 326 km/h (202 MPH)

Actual wheel speed

Similar speed as indicated on speed meter

WHEEL SPD RL

Wheel speed sensor (RL) reading / min.: 0 km/h (0 MPH, max.: 326 km/h (202 MPH)

Actual wheel speed

Similar speed as indicated on speed meter

DECELERAT SENS

Deceleration sensor 1 reading / min.: -1.869 G, max.: 1.869 G

Approximately 0 +- 0.13G at still condition

Reading changes when vehicle is bounced

DECELERAT SENS2

Deceleration sensor 2 reading / min.: -1.869 G, max.: 1.869 G

Approximately 0 +- 0.13G at still condition

Reading changes when vehicle is bounced

IG VOLTAGE

ECU power supply voltage / UNDER / NORMAL

NORMAL: 9.5 V or over UNDER: Below 9.5 V

SFRR

ABS solenoid (SFRR) / ON or OFF

ON: Operate

SFRH

ABS solenoid (SFRH) / ON or OFF

ON: Operate

SFLR

ABS solenoid (SFLR) / ON or OFF

ON: Operate

SFLH

ABS solenoid (SFLH) / ON or OFF

ON: Operate

SRRR (SRR)

ABS solenoid (SRRR (SRR)) / ON or OFF

ON: Operate

SRRH (SRH)

ABS solenoid (SRRH (SRH)) / ON or OFF

ON: Operate

SRLR

ABS solenoid (SRLR) / ON or OFF

ON: Operate

SRLH

ABS solenoid (SRLH) / ON or OFF

ON: Operate

SMF (BA-SOL)

TRAC solenoid (SMF) / ON or OFF

ON: Operate

SMR

TRAC solenoid (SMR) / ON or OFF

ON: Operate

THROTTLE

Throttle position sensor/ Min.: 0 deg, Max.: 125 deg

Release accelerator pedal: Approx. 0 deg.
Depress accelerator pedal: Approx. 90 deg.

ENGINE SPD

Engine Speed/ Min.: 0 rpm, Max.: 6000 rpm

Actual engine speed

VEHICLE SPD

Maximum wheel speed sensor reading / min.: 0 km/h (0 MPH), max.: 326 km/h (202 MPH)

Actual vehicle speed

Speed indicated on speedometer

YAW RATE

Yaw rate sensor/ Min.: -128 deg/s, Max.: 128 deg/s

Min.: -128 deg/s
Max.: 128 deg/s

YAW ZERO VALUE

Memorized zero value/ Min.: -128 deg/s, Max.: 128 deg/s

Min.: -128 deg/s
Max.: 128 deg/s

STEERING ANG

Steering sensor/ Min.: -1152 deg, Max.: 1150.875 deg

Left turn: Increase
Right turn: Decrease

MAS CYL PRS 1

Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V

When brake pedal is released: 0.3 to 0.9 V

Reading increases when brake pedal is depressed

TEST MODE

Test mode / NORMAL or TEST

NORMAL: Normal mode
TEST: During test mode

#CODES

Number of DTC recorded / min.: 0, max.: 255

Min.: 0, max.: 39

⁽¹⁾

2WD

ACTIVE TEST

HINT:

Performing the ACTIVE TEST using the intelligent tester allows the relay and actuator, etc. to operate without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten labor time.

It is possible to display the DATA LIST during the ACTIVE TEST.

Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
According to the display on the tester, perform the "ACTIVE TEST".
HINT:

Ignition switch must be turned to the ON position to proceed to the Active Test using the intelligent tester.

ACTIVE TEST REFERENCE CHART

Item

Vehicle Condition / Test Details

Diagnostic Note

SFRR

Turns ABS solenoid (SFRR) ON / OFF