LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2006 >> RX 400h AWD >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Brake Control >> Electronically Controlled Brake System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT:

    With the intelligent tester connected to the DLC3 and the ignition switch ON, the ECB, ABS, and VSC data list can be displayed. Follow the prompts on the tester screen to access the DATA LIST.

    ABS / VSC / TRAC: 

    ABS / VSC / TRAC ITEM REFERENCE

    Item (Display) Measurement Item/ Range (Display) Normal Condition Diagnostic Note
    ECB MTR RELAY ECB motor relay / ON or OFF ON: Motor relay ON
    OFF: Motor relay OFF    		 -
    IDLE SW Main idle switch / ON or OFF ON: Accelerator pedal released
    OFF: Accelerator pedal depressed    		 -
    STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
    OFF: Brake pedal released    		 -
    PARKING BRAKE SW Parking brake switch / ON or OFF ON: Parking brake applied
    OFF: Parking brake released    		 -
    LEVER POSITION Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL - -
    FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer
    FL WHEEL SPD Wheel speed sensor (FL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer
    RR WHEEL SPD Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer
    RL WHEEL SPD Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual wheel speed Similar speed as indicated on speedometer
    DECELERATE SEN Deceleration sensor 1 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced
    DECELERATE SEN 2 Deceleration sensor 2 reading / min.: -18.52 m/s2 , max.: -18.33 m/s2 Approximately m/s2 while stationary Reading changes when vehicle is bounced
    FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    RR SPD OPN RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    RL SPD OPN RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    YAW RATE OPN Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    DECELERATE OPN Deceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    STEERING OPN Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    M/C OPN Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    ABS WARN LAMP ABS warning light / ON or OFF ON: Warning light ON
    OFF: Warning light OFF    		 -
    BRAKE WARN LAMP BRAKE warning light / ON or OFF ON: Warning light ON
    OFF: Warning light OFF    		 -
    SLIP INDI LAMP SLIP indicator light / ON or OFF ON: Indicator light ON
    OFF: Indicator light OFF    		 -
    BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
    OFF: Buzzer OFF    		 -
    VSC WARN LAMP VSC warning light / ON or OFF ON: Warning light ON
    OFF: Warning light OFF    		 -
    VEHICLE SPD Maximum wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) Actual vehicle speed Speed indicated on speedometer
    FR WHEEL ACCEL FR wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2 Max.: 199.27 m/s2 -
    FL WHEEL ACCEL FL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2 Max.: 199.27 m/s2 -
    RR WHEEL ACCEL RR wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2 Max.: 199.27 m/s2 -
    RL WHEEL ACCEL RL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2 Max.: 199.27 m/s2 -
    ZERO DECELERATE Memorized zero value / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2 Max.: 24.91 m/s2 -
    ZERO DECELERATE 2 Memorized zero value / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2 Max.: 24.91 m/s2 -
    ZERO STEERING Memorized zero value / min.: - 3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg Max.: 3276.7 deg -
    LATERAL G Lateral G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2 Max.: 24.91 m/s2 -
    FORWARD & REA G Forward and rearward G / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2 Max.: 24.91 m/s2 -
    YAW RATE VALUE Yaw rate value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s Max.: 127 deg/s -
    STEERING ANGLE Steering angle value / min.: - 3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg Max.: 3276.7 deg -
    TRAC STATUS TRAC control status / ON or OFF ON: During the control -
    TRAC BRK STATUS TRAC brake control status / ON or OFF ON: During the control -
    FR VSC STATUS FR wheel VSC control status / ON or OFF ON: During the control -
    FL VSC STATUS FL wheel VSC control status / ON or OFF ON: During the control -
    RR VSC STATUS RR wheel VSC control status / ON or OFF ON: During the control -
    RL VSC STATUS RL wheel VSC control status / ON or OFF ON: During the control -
    YAW RATE SENS 1 Yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s Max.: 127 deg/s -
    YAW RATE SENS 2 Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s Max.: 127 deg/s -
    ZERO YAW RATE Memorized zero value / min.: - 128 deg/s, max.: 127 deg/s Min.: -128 deg/s Max.: 127 deg/s -
    ZERO YAW RATE 2 Memorized zero value / min.: - 128 deg/s, max.: 127 deg/s Min.: -128 deg/s Max.: 127 deg/s -
    STEERING SEN Steering angle sensor / min.: - 3276.8 deg, max.: 3276.7 deg Left turn: Increase Right turn: Decrease -
    MAS CYL PRESS 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed
    MAS CYL PRESS 2 Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed
    FR ABS STATUS FR wheel ABS control status / ON or OFF ON: During the control -
    FL ABS STATUS FL wheel ABS control status / ON or OFF ON: During the control -
    RR ABS STATUS RR wheel ABS control status / ON or OFF ON: During the control -
    RL ABS STATUS RL wheel ABS control status / ON or OFF ON: During the control -
    BA STATUS BA control status / ON or OFF ON: During the control -
    PBA STATUS PBA control status / ON or OFF ON: During the control -
    INSPECTION MODE Inspection mode / OTHER or INSPECT - -
    #IG ON2 Number of IG ON after entering the inspection mode / min.: 0, max.: 255 - -
    PEDAL STROKE Stroke sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.7 to 1.3 V -
    PEDAL STROKE 2 Stroke sensor 2 / min.: 0 V, max.: 5 V When brake pedal is released: 3.7 to 4.3 V -
    ACC PRESS SENS Accumulator pressure sensor / min.: 0 V, max.: 5 V Specified value: 3.2 to 4.0 V -
    FR W/C SENS FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V -
    FL W/C SENS FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V -
    RR W/C SENS RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V -
    RL W/C SENS RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V -
    RESERVOIR SW Brake fluid level warning switch / ON or OFF ON: Reservoir level normal
    OFF: Reservoir level low    		 -
    ECB WARN LAMP ECB warning light / ON or OFF ON: Warning light ON
    OFF: Warning light OFF    		 -
    FR RQST TORQ Front regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - -
    FR OPERATE TORQ Front regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - -
    RR RQST TORQ Rear regenerative request torque / min.: 0 N*m, max.: 4,080 N*m - -
    RR OPERATE TORQ Rear regenerative operation torque / min.: 0 N*m, max.: 4,080 N*m - -
    REGEN COOP Regenerative cooperation / ON or OFF ON: Operate -
    OFF: Not operate -
    ECB MTR RELAY 2 ECB motor relay 2 / ON or OFF ON: Motor relay ON
    OFF: Motor relay OFF    		 -
    ECB RELAY ECB main relay / ON or OFF ON: Main relay ON
    OFF: Main relay OFF    		 -
    ECB RELAY 2 ECB main relay 2 / ON or OFF ON: Main relay ON
    OFF: Main relay OFF    		 -
    VOLT M/C SEN Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V - -
    VOLT M/C SEN 2 Voltage of master cylinder pressure sensor 2 / min.: -2.5 V, max.: 2.49 V - -
    VOLT STROK SEN Voltage of stroke sensor / min.: - 2.5 V, max.: 2.49 V - -
    VOLT STROK SEN 2 Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V - -
    SLAFR CUR SLAFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLAFL CUR SLAFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLARR CUR SLARR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLARL CUR SLARL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLRFR CUR SLRFR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLRFL CUR SLRFL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLRRR CUR SLRRR solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    SLRRL CUR SLRRL solenoid current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A -
    M/C2 OPN Master cylinder pressure sensor 2 open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    STROKE OPN Stroke sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    FR W/C OPN FR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    FL W/C OPN FL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    RR W/C OPN RR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    RL W/C OPN RL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    ACC OPN Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
    NORMAL: Normal    		 -
    SMC1 ECB solenoid (SMC1) / ON or OFF ON: Operate
    OFF: Not operate    		 -
    SMC2 ECB solenoid (SMC2) / ON or OFF ON: Operate
    OFF: Not operate    		 -
    SCSS ECB solenoid (SCSS) / ON or OFF ON: Operate
    OFF: Not operate    		 -
    # DTC Number of DTC recorded / min.: 0, max.: 255 - -
  2. ACTIVE TEST 

    HINT:

    Performing the ACTIVE TEST using the intelligent tester allows the relay, actuator, etc. to operate without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch on.
    3. According to the display on the tester, perform the "ACTIVE TEST".

      HINT:

      The ignition switch must be turned to the ON position to proceed to the ACTIVE TEST using the intelligent tester.

      ABS / VSC / TRAC: 

      ABS / VSC / TRAC ITEM REFERENCE

      Item (Display) Vehicle Condition / Test Details Diagnostic Note
      ABS WARN LAMP Turns ABS warning light ON / OFF Observe combination meter
      VSC WARN LAMP Turns VSC warning in multi information display ON / OFF Observe combination meter
      BRAKE WARN LAMP Turns BRAKE warning light ON / OFF Observe combination meter
      SLIP INDI LAMP Turns SLIP indicator light ON / OFF Observe combination meter
      ECB WARN LAMP Turns brake control warning light ON / OFF Observe combination meter
      BUZZER Turns skid control buzzer ON / OFF Buzzer can be heard
      STP LAMP RELAY Turns stop light operation relay ON / OFF Observe rear combination light (stop light) (Does not come on for 5 sec. or more)
      ECB RELAY Turns ABS No.1 relay ON / OFF Operating sound of relay (clicking sound) can be heard
      ECB RELAY 2 Turns ABS No.2 relay ON / OFF Operating sound of relay (clicking sound) can be heard
      ECB MTR RELAY Turns ABS MTR1 motor relay ON / OFF Operating sound of relay (clicking sound) can be heard
      ECB MTR RELAY 2 Turns ABS MTR2 relay ON / OFF Operating sound of relay (clicking sound) can be heard
      SMC1 Turns ECB solenoid (SMC1) ON / OFF Operating sound of solenoid (clicking sound) can be heard
      SMC2 Turns ECB solenoid (SMC2) ON / OFF Operating sound of solenoid (clicking sound) can be heard
      SCSS Turns ECB solenoid (SCSS) ON / OFF Operating sound of solenoid (clicking sound) can be heard
scientia non olet · About LEMON Manuals