Problem Symptoms Table

If a normal system code is displayed during the DTC check, but the problem still occurs, check the circuits for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.

HINT:

• The following is the troubleshooting procedure for the wireless door lock control of a vehicle without the smart key system.
• Inspect the fuse and relay before investigating the suspected areas shown in the table below.
• Inspect each malfunction circuit in numerical order for its corresponding symptom.

  WIRELESS DOOR LOCK CONTROL SYSTEM: 

  WIRELESS DOOR LOCK CONTROL SYSTEM PROBLEM SYMPTOMS CHART
  
  

  Symptom	Suspected Area	Refer To
  The wireless door lock control system does not operate	1. Perform the operation check	OPERATION CHECK
  	2. Check if the CAN communication DTC is output	DIAGNOSTIC TROUBLE CODE CHART
  	3. Door control transmitter	DOOR CONTROL TRANSMITTER
  	4. Door courtesy switch circuit	DOOR COURTESY SWITCH CIRCUIT
  	5. Luggage compartment door courtesy switch	LUGGAGE COMPARTMENT DOOR COURTESY SWITCH CIRCUIT
  	6. Power source circuit	POWER SOURCE CIRCUIT
  	7. Replace door control receiver	-
  	8. Replace certification ECU	-
  	9. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The automatic lock function does not operate normally.	1. Perform the operation check	OPERATION CHECK
  	2. Door courtesy switch circuit	DOOR COURTESY SWITCH CIRCUIT
  	3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The illuminated entry function only does not operate.	1. Perform the operation check	OPERATION CHECK
  	2. Lighting system	PROBLEM SYMPTOMS TABLE
  	3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The answer back function does not operate (Wireless door lock buzzer).	1. Perform the operation check	OPERATION CHECK
  	2. Wireless door lock buzzer circuit	WIRELESS DOOR LOCK BUZZER CIRCUIT
  	3. Replace certification ECU	-
  	4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The answer back function does not operate (Hazard warning light).	1. Perform the operation check	OPERATION CHECK
  	2. Wire harness	-
  	3. Turn signal flasher assembly	TURN SIGNAL FLASHER ASSEMBLY
  	4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The door ajar warning function only does not operate	1 Perform the operation check	OPERATION CHECK
  	2. Door courtesy switch circuit	DOOR COURTESY SWITCH CIRCUIT
  	3 If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The panic alarm function only does not operate	1. Perform the operation check	OPERATION CHECK
  	2 Door control transmitter	DOOR CONTROL TRANSMITTER
  	3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The panic alarm function does not operate (Vehicle horn)	1. Perform the operation check	OPERATION CHECK
  	2. Horn circuit	HORN CIRCUIT
  	3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The panic alarm function does not operate (Security horn).	1. Perform the operation check	OPERATION CHECK
  	2. Security horn circuit	SECURITY HORN CIRCUIT
  	3. Replace certification ECU	-
  	4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The panic alarm function does not operate (Hazard warning light).	1. Perform the operation check	OPERATION CHECK
  	2. Wire harness	-
  	3. Turn signal flasher assembly	TURN SIGNAL FLASHER ASSEMBLY
  	4. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-
  The panic alarm function does not operate (Headlight or taillight).	1. Perform the operation check	OPERATION CHECK
  	2. Lighting system	PROBLEM SYMPTOMS TABLE
  	3. If the symptom still occurs after the above areas have been inspected and proved to be normal, replace the main body ECU (Instrument panel J/B)	-