Specifications Index
GS350/460 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 294 N.m (2,998 kgf.cm 217 ft.lbf) | ||
| Rear | 290 N.m (2,957 kgf.cm 214 ft.lbf) | ||
| Battery | ON-VEHICLE INSPECTION | ||
| Brakes (1UR-FSE) | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Brakes (2GR-FSE) | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging (1UR-FSE) | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging (2GR-FSE) | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts (1UR-FSE) | |||
| Belt Routing | DRIVE BELT | ||
| Belt Tensioning | INSTALLATION | ||
| Drive Belts (2GR-FSE) | |||
| Belt Routing | DRIVE BELT | ||
| Belt Tensioning | INSTALLATION | ||
| Engine Cooling (1UR-FSE) | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | Standard valve (for brand-new cap) 93.3 to 122.7 kPa (0.95 to 1.25 kgf/cm2 , 13.5 to 17.8 psi) Minimum standard valve (after using cap) 78.5 kPa (0.8 kgf/cm2 , 11.4 psi) |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Cooling (2GR-FSE) | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | Standard valve (for brand-new cap) 93.3 to 122.7 kPa (0.95 to 1.25 kgf/cm2 , 13.5 to 17.8 psi) Minimum standard valve (after using cap) 78.5 kPa (0.8 kgf/cm2 , 11.4 psi) |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical (1UR-FSE) | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | At Idle: 70 kPa (0.7 kgf.cm2 , 10.1 psi) or more At 2,500 RPM: 220 kPa (2.2 kgf.cm2 , 31.9 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Engine Mechanical (2GR-FSE) | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | At Idle: 80 kPa (0.8 kgf.cm2 , 11.6 psi) or more At 2,500 RPM: 250 kPa (2.6 kgf.cm2 , 36.4 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque (1UR-FSE) | Step1: 30 N.m (306 kgf.cm, 22 ft.lbf) Step2: Turn 90° |
||
| Flywheel/Flex Plate (Drive Plate) Torque (2GR-FSE) | 83 N.m (850 kgf.cm, 61 ft.lbf) | ||
| Fuel System (1UR-FSE) | |||
| Pressure Specification | 196 to 588 kPa (2 to 6 kgf/cm2 , 28 to 85 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| Fuel System (2GR-FSE) | |||
| Pressure Specification | 196 to 588 kPa (2 to 6 kgf/cm2 , 28 to 85 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug (1UR-FSE) | |||
| Type | DENSO FK20HBR11 | ||
| Gap | Standard electrode gap: 1.0 - 1.1 mm (0.039 - 0.043 in.) Maximum electrode gap: 1.3 mm (0.051 in.) |
||
| Torque | 18 N.m (184 kgf.cm, 13 ft.lbs) | ||
| Spark Plug (2GR-FSE) | |||
| Type | DENSO FK20HR11 | ||
| Gap | Standard electrode gap : 1.0 - 1.1 mm (0.039 - 0.043 in.) Maximum electrode gap: 1.4 mm (0.055 in.) |
||
| Torque | 18 N.m (184 kgf.cm, 13 ft.lbs) | ||
| Starting (1UR-FSE) | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Starting (2GR-FSE) | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Front | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Rear | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 N.m (1,050 kgf.cm 76 ft.lbf) | ||