Data List/Active Test

HINT:

According to the DATA LIST displayed on Techstream, the value and status of the switch, sensor, actuator, etc. can be obtained without part removal. Reading the DATA LIST as the first step in troubleshooting is one way to shorten labor time.

1. Connect Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. From the display on the tester, read the "DATA LIST".
   NORMAL CONDITION ITEM RANGE REFERENCE
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Vehicle Speed	Vehicle speed reading/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	Speed indicated on speedometer
   IG Power Source Voltage	ECU power supply voltage/min.: 0 V, max.: 25.5 V	Actual ECU power supply voltage: 10 to 14 V	-
   Steering Angle	Steering angle sensor reading/min.: -73725.75 deg, max.: 73728 deg	Actual steering angle Left turn: Reading increases Right turn: Reading decreases	Zero point is set when the battery is connected
   Engine Speed	Cam position sensor reading/min.: 0 rpm, max.: 25,500 rpm	Actual engine speed	Speed indicated on the combination meter
   Stop Light Switch	Stop light switch/ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
   Damping Force Switch 1	Damping force switch 1/ON or OFF	The same as absorber control switch position	Operate the absorber control switch
   TS Terminal	TS terminal/ON or OFF	ON: During test mode OFF: Normal mode	-
   TC Terminal	TC terminal/ON or OFF	ON: DTC recorded OFF: No DTC recorded	-
   G (Up & Down) Sensor FR	G (up & down) FR sensor reading/min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (FR) is bounced
   G (Up & Down) Sensor FL	G (up & down) FL sensor reading/min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (FL) is bounced
   G (Up & Down) Sensor Rear	G (up & down) rear sensor reading/min.: -1045267.3 mm/s2 , max.: 1045299.2 mm/s2	-8820 mm/s2 to 980 mm/s2 at still condition	Reading changes when vehicle (rear) is bounced
   Damper Step FR	Damper step FR/min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   Damper Step FL	Damper step FL/min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   Damper Step RR	Damper step RR/min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   Damper Step RL	Damper step RL/min.: 0 step, max.: 255 step	Min.: 1 step, max.: 17 step	-
   Wheel Speed FR	Front right wheel speed reading/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	Speed indicated on speedometer
   Max Damper Step FR	Max. damper step FR/min.: 0 step, max.: 255 step	17 step at still condition	-
   Max Damper Step FL	Max. damper step FL/min.: 0 step, max.: 255 step	17 step at still condition	-
   Max Damper Step RR	Max. damper step RR/min.: 0 step, max.: 255 step	17 step at still condition	-
   Max Damper Step RL	Max. damper step RL/min.: 0 step, max.: 255 step	17 step at still condition	-
   Number of Trouble Code	Number of DTC recorded/min.: 0, max.: 255	Min.: 0, Max.: XX	-

HINT:

Performing the ACTIVE TEST using Techstream allows the relay, actuator, etc. to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

1. Connect Techstream to DLC3.
2. Turn the engine switch on (IG).
3. According to the display on the tester, perform the "ACTIVE TEST".
   CONTROL RANGE REFERENCE
   
   

   Tester Display	Test Part	Control Range
   Damper Step FR	Damper step front right wheel	1 step to 17 steps (Damper step is change)
   Damper Step FL	Damper step front left wheel	1 step to 17 steps (Damper step is change)
   Damper Step RR	Damper step rear right wheel	1 step to 17 steps (Damper step is change)
   Damper Step RL	Damper step rear left wheel	1 step to 17 steps (Damper step is change)