Park/Neutral Position Switch: Installation

INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
1. Install the switch to the manual valve shaft.
2. Temporarily install the bolt.
  
  Fig 1: Locating Bolt And Switch
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install a new lock washer with the nut.
  Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf)
  
  Fig 2: Locating Lock Nut And Lock Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Temporarily install the control shaft lever with shifting rod.
  
  Fig 3: Locating Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.
6. Remove the control shaft lever with shifting rod.
  
  Fig 4: Turning Control Shaft Lever
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Align the groove with the neutral basic line.
8. Hold the switch in this position and tighten the bolt.
  Torque: 13 N*m (130 kgf*cm, 9 ft.*lbf)
  
  Fig 5: Aligning Groove With Neutral Basic Line
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Using a screwdriver, bend the tabs of the lock washer.
  HINT:
  
  Bend at least 2 washer tabs.
  
  Fig 6: Bending Tabs Of Lock Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Install the transmission control shaft lever with the spring washer and nut.
  Torque: 16 N*m (160 kgf*cm, 12 ft.*lbf)
  
  Fig 7: Locating Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. Connect the switch connector.
  
  Fig 8: Locating Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR ENGINE MOUNTING MEMBER
1. Install the rear engine mounting member with the 4 bolts.
  Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf)
  
  Fig 9: Locating Rear Engine Mounting Member With Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
1. Temporarily connect the shifting rod to the connecting rod swivel with the nut.
  HINT:
  
  The nut will be tightened to the specified torque during the shift lever position adjustment procedure.
ADJUST SHIFT LEVER POSITION
1. Adjust the shift lever position (see ADJUSTMENT ).
  
  Fig 10: Locating Floor Shift Gear Shifting Rod Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR PROPELLER SHAFT ASSEMBLY (See INSTALLATION )
FULLY TIGHTEN NO. 1 CENTER SUPPORT BEARING ASSEMBLY (See INSTALLATION )
INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE (See INSTALLATION )
INSTALL AIR GUIDE PLATE OUTSIDE RH (See INSTALLATION )
INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR (See INSTALLATION )
INSTALL FRONT EXHAUST PIPE ASSEMBLY (See REMOVAL )
CONNECT HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) (See INSTALLATION )
CONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) (See INSTALLATION )
INSTALL FRONT FLOOR COVER CENTER LH (See INSTALLATION )
INSTALL FRONT FLOOR COVER CENTER RH (See INSTALLATION )
INSTALL FRONT CENTER FLOOR BRACE (See INSTALLATION )
INSTALL REAR NO. 1 FLOOR PANEL BRACE (See INSTALLATION )
INSTALL NO. 2 ENGINE UNDER COVER
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
1. Inspect the switch (see ON-VEHICLE INSPECTION ).
INSPECT FOR EXHAUST GAS LEAK