Road Test

PROBLEM SYMPTOM CONFIRMATION
1. Based on the result of the customer problem analysis, try to reproduce the symptoms If the problem is that the transmission does not shift up or shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms

ROAD TEST

NOTE: Perform the test at an ATF (Automatic Transmission Fluid) temperature 60 to 110°C (140 to 230°F) during normal operation.

D position test (NORM and SPORT pattern) Move the shift lever to D and fully depress the accelerator pedal Check the following
1. Check up-shift operation
  Check that the 1 → 2, 2 → 3, 3 → 4, 4 → 5, 5 → 6, 6 → 7 and 7 → 8 up-shifts take place at the shift points shown in the automatic shift schedule
  
  HINT:
  
  Lock-up Prohibition Control
  - Brake pedal is depressed
  - Accelerator pedal is released
  - Engine coolant temperature is 60°C (140°F) or less.
2. Check for shift shock and slippage.
  Check for shock and slippage at the 1 → 2, 2 → 3, 3 → 4, 4 → 5, 5 → 6, 6 → 7 and 7 → 8 upshifts
3. Check for abnormal noise and vibration
  Check for abnormal noise and vibration when up-shifting from 1 → 2, 2 → 3, 3 → 4,4 → 5, 5 → 6, 6 → 7 and 7 → 8 while driving with the shift lever in D, and check while driving with lock-up on
  
  NOTE: If abnormal noise and/or vibration occur, conduct a thorough check of the cause. Failure to repair the problem may lead to subsequent problems in the differential, torque converter, etc.
4. Check kick-down operation
  While driving the vehicle in 2nd, 3rd, 4th, 5th, 6th, 7th and 8th gears with the shift lever in D, check that the possible kick-down vehicle speed limits for the 2 → 1, 3 → 2, 4 → 3, 5 → 4, 6 → 5, 7 → 6 and 8 → 7 kick-downs conform to those indicated in the automatic shift schedule
5. Check for abnormal shock and slippage at kick-down
6. Check the lock-up mechanism.
  - Drive the vehicle in 6th, 7th or 8th gear with the shift lever in D Maintain a steady speed (lock-up ON).
  - Lightly depress the accelerator pedal and check that the engine speed does not change abruptly
  HINT.
  - There is no lock-up function in 1st, 2nd, 3rd, 4th and 5th gears when the shift lever is in D
  - If there is a sudden increase in engine speed, there is no lock-up

D position (fixed range mode) test

Check paddle switch operation

HINT

When the vehicle is being operated in D position (fixed range mode), if the vehicle is stopped or the accelerator pedal is kept steady for a certain period of time with the transmission in the same gear, the vehicle will change back automatically to normal D position operation

Initial shift range when the "-" paddle switch is operated with the shift lever in D The initial shift range selected is based on vehicle speed and the gear that was in use prior to operating the "-" paddle switch. In the following 2 tables, based on the gear in use and vehicle speed, there may be 2 different possible initial shift ranges The range that will be selected is the lower of the 2

VEHICLE SPEED REFERENCE

Vehicle speed km/h (mph)	0 to 58 (0 to 36)	58 to 65 (36 to 40)	65 to 83 (40 to 52)	83 to 90 (52 to 56)
Initial shift range when operating "-" paddle switch	D4	D4 or D5	D5	D5 or D6

GEAR DRIVING POSITION

Gear in use when driving in D position	1st	2nd	3rd	4th	5th	6th	7th	8th
Initial shift range	D1	D1	D2	D3	D4	D5	D6	D7

Engine over-revving prevention when in D position (fixed range mode).
To prevent engine over-revving when the "-" paddle switch is operated, selection of lower shift ranges will not be performed when the actual vehicle speed is greater than the speed ranges shown below

RANGE DECREASE REFERENCE

Range Decrease

D2 to D1

D3 to D2

Vehicle speed at which shift range decrease is permitted km/h (mph)⁽¹⁾

38 to 44 (24 to 27)

71 to 78 (44 to 48)

⁽¹⁾	Differences in tire sizes, etc. cause the "Vehicle speed at which shift range decrease is permitted" to have a range, as shown above.

The shift range and gear when the "-" paddle switch is operated will be selected based on the shift range and gear that were in use before operating the "-" paddle switch

PADDLE SWITCH REFERENCE

		Range before operating the "-" paddle switch
		D8	D7	D6	D5	D4	D3	D2	D1
Gear before operating the "-" paddle switch	8th	D7 range 7th gear	-	-	-	-	-	-	-
	7th	D6 range 6th gear	D6 range 6th gear	-	-	-	-	-	-
	6th	D5 range 5th gear	D5 range 5th gear	D5 range 5th gear	-	-	-	-	-
	5th	D4 range 4th gear	D4 range 4th gear	D4 range 4th gear	D4 range 4th gear	-	-	-	-
	4th	D4 range 4th gear	D4 range 4th gear	D4 range 4th gear	D4 range 4th gear	D3 range 3rd gear	-	-	-
	3rd	D4 range 3rd gear	D4 range 3rd gear	D4 range 3rd gear	D4 range 3rd gear	D3 range 3rd gear	D2 range 2nd gear	-	-
	2nd	D4 range 2nd gear	D4 range 2nd gear	D4 range 2nd gear	D4 range 2nd gear	D3 range 2nd gear	D2 range 2nd gear	D1 range 1st gear	-
	1st	D4 range 1st gear	D4 range 1st gear	D4 range 1st gear	D4 range 1st gear	D3 range 1st gear	D2 range 1st gear	D1 range 1st gear	D1 range 1st gear
Example: When the "-" paddle switch is operated with the D6 range selected and the transmission in 6th gear, the D5 range and 5th gear will be selected. When the "-" paddle switch is operated with the D6 range selected and the transmission in 3rd gear, the D4 range and 3rd gear will be selected When the "-" paddle switch is operated with the D4 range selected and the transmission in 4th gear, the D3 range and 3rd gear will be selected When the "-" paddle switch is operated with the D4 range selected and the transmission in 3rd gear, the D3 range and 3rd gear will be selected

M position test

NOTE: If the shift lever is moved from D to M during the system check that occurs after the engine switch is turned on (IG), both D position control and the D indication on the shift range indicator will continue until the system is confirmed to be normal.
If the shift lever is moved from D to M after the system check completes, M position control will be performed.

Check shift operation

Check that no gear shift occurs when the shift position is changed from D to M while driving.
Engine over-revving prevention when the shift lever is in M.
To prevent engine over-revving, selection of lower gears will not be performed when the actual vehicle speed is greater than the speed ranges shown below

GEAR DECREASE REFERENCE

Gear Decrease

2 to 1

Vehicle speed at which gear decrease is permitted km/h (mph)⁽¹⁾

38 to 57 (24 to 35)

⁽¹⁾	Differences in tire sizes, etc. cause the "Vehicle speed at which gear decrease is permitted" to have a range, as shown above.

While driving with the shift lever in M, selection of lower gears will automatically be performed when the vehicle speed drops below the speed ranges shown below

VEHICLE SPEED REFERENCE

Gear

2 to 1

3 to 2

4 to 3

5 to 4

6 to 5

7 to 6

8 to 7

Vehicle speed for each automatic downshift km/h (mph)⁽¹⁾

10 to 15 (6 to 9)

15 to 20 (9 to 12)

35 to 41 (22 to 25)

42 to 48 (26 to 30)

53 to 59 (33 to 37)

56 to 62 (35 to 39)

67 to 74 (42 to 46)

⁽¹⁾	Differences in tire sizes, etc. cause the "Vehicle speed for each automatic downshift" to have a range, as shown above.

R position test
Move the shift lever to R and lightly depress the accelerator pedal Check that the vehicle moves backward without any abnormal noise or vibration

CAUTION: Before conducting this test, ensure that no people or obstacles are in the test area.
P position test
Stop the vehicle on an incline (more than 5°) Then move the shift lever to P and release the parking brake Check that the parking lock pawl holds the vehicle in place