Park / Neutral Position Switch: Installation

INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
1. Install the switch to the manual valve shaft.
2. Temporarily install the bolt.
  
  Fig 1: Locating Park/Neutral Position Switch Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install a new lock washer with the nut
  Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf)
  
  Fig 2: Locating Lock Washer With Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Temporarily install the control shaft lever with shifting rod.
  
  Fig 3: Identifying Transmission Control Shaft Lever With Shifting Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to N.
  
  Fig 4: Identifying Control Shaft Lever Position
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the control shaft lever with shifting rod
  
  Fig 5: Identifying Transmission Control Shaft Lever With Shifting Rod
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Align the groove with the neutral basic line.
8. Hold the switch in this position and tighten the bolt.
  Torque: 13 N*m (130 kgf*cm, 9 ft.*lbf)
  
  Fig 6: Aligning Groove With Neutral Basic Line
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Using a screwdriver, bend the tabs of the lock washer.
  HINT.
  
  Bend at least 2 washer tabs
  
  Fig 7: Bending Tabs Of Lock Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Install the transmission control shaft lever with the spring washer and nut
  Torque: 16 N*m (160 kgf*cm, 12 ft.*lbf)
  
  Fig 8: Locating Transmission Control Shaft Lever With Spring Washer And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. Connect the switch connector
  
  Fig 9: Locating Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR ENGINE MOUNTING MEMBER
1. Install the rear engine mounting member with the 4 bolts
  Torque: 26 N*m (260 kgf*cm, 19 ft.*lbf)
  
  Fig 10: Locating Engine Rear Mounting Member Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
1. Temporarily tighten the floor shift gear shifting rod sub-assembly with the nut
Fig 11: Locating Floor Shift Gear Shifting Rod Nut
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
ADJUST SHIFT LEVER POSITION (See ADJUSTMENT )
INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (See INSTALLATION )
FULLY TIGHTEN NO. 1 CENTER SUPPORT BEARING ASSEMBLY (See INSTALLATION )
INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE (See INSTALLATION )
INSTALL OUTSIDE AIR GUIDE PLATE RH (See INSTALLATION )
INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR (See INSTALLATION )
INSTALL FRONT EXHAUST PIPE ASSEMBLY (See INSTALLATION )
CONNECT HEATED OXYGEN SENSOR (See INSTALLATION )
INSTALL TAIL EXHAUST PIPE ASSEMBLY (See INSTALLATION )
INSTALL FRONT CENTER FLOOR BRACE (See INSTALLATION )
INSTALL REAR NO. 1 FLOOR PANEL BRACE (See INSTALLATION )
INSTALL ENGINE UNDER COVER AIR GUIDE BRACKET (See INSTALLATION )
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
1. Inspect the switch (See REMOVAL )
INSPECT SHIFT LEVER POSITION (See ON-VEHICLE INSPECTION )
INSPECT FOR EXHAUST GAS LEAK
INSTALL NO. 2 FLOOR UNDER COVER (See INSTALLATION )
INSTALL NO. 1 FLOOR UNDER COVER (See INSTALLATION )
INSTALL NO. 2 ENGINE UNDER COVER