LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> LS 600hL >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/WINDOWGLASS >> Windshield Glass >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Windshield Glass: Installation

HINT

A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS )

  1. INSTALL NO. 1 WINDSHIELD GLASS STOPPER 
    1. Install 2 new stoppers to the vehicle body as shown in the illustration.
  2. INSTALL NO. 2 WINDSHIELD GLASS STOPPER 
    1. Apply Primer G to the glass where the stopper will be installed
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
      Fig 1: Identifying Stoppers To Vehicle Body
      G04952187Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install 2 new stoppers onto the glass as shown in the illustration
    Fig 2: Identifying Stoppers Onto Glass
    G04952188Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL WINDSHIELD OUTSIDE MOULDING UPPER 
    1. Using a brush or sponge, coat the contact surface of the glass and moulding with Primer G
      NOTE:
      • Allow the primer coating to dry for 3 minutes or more.
      • Do not coat the adhesive with Primer G.
      • Throw away any leftover primer.
    2. Apply adhesive to the moulding as shown in the illustration.

      Adhesive: 

      Toyota Genuine Windshield Glass Adhesive or equivalent 

      HINT.

      Use all adhesive within the time written in the table below.

      Usage timeframe 

      TEMPERATURE SPECIFICATION

      Temperature Usage Timeframe
      35°C (95°F) 15 minutes
      20°C (68°F) 1 hour 40 minutes
      5°C (41 °F) 8 hours
      Fig 3: Applying Adhesive To Moulding
      G04952189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the windshield outside moulding, as shown in the illustration.
      NOTE: Make sure the glass and moulding are flush.
      Fig 4: Identifying Windshield Outside Moulding
      G04952190Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove any unnecessary adhesive before it hardens.
    NOTE: Make sure that no adhesive remains on the moulding and glass.
  4. INSTALL WINDSHIELD GLASS RETAINER 
    1. Apply Primer G to the glass where the retainer will be installed.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
      Fig 5: Identifying Adhesive Applying Area
      G04952191Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install 2 new retainers onto the glass as shown in the illustration.
    Fig 6: Identifying Retainers Onto Glass
    G04952192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Standard 

    SPECIFIED CONDITION CHART

    Area Specified Condition
    a 30 mm (1.18 in.)
  5. INSTALL WINDSHIELD GLASS ADHESIVE DAM 
    1. Apply Primer G to the glass where the glass adhesive dams will be installed.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
    2. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the area above the notches on the upper part of the glass.
    Fig 7: Identifying Windshield Glass Adhesive Dam Installation Position
    G04952193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL WINDSHIELD GLASS SEAL 
    1. Apply Primer G to the glass where the windshield glass seal will be installed.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
    2. Remove the peeling paper from the windshield glass seal. Install the seal to the glass
    Fig 8: Identifying Windshield Glass Seal Paper Installation Position
    G04952194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Standard 

    SPECIFIED CONDITION CHART

    Area Specified Condition
    a 30.0 mm (1.18 in.)
    b 20.0 mm (0.787 in.)
    c 10.0 mm (0.394 in.)
    d 13.0 mm (0.512 in.)
    e 88.7 mm (3.49 in.)
  7. INSTALL WINDSHIELD GLASS 
    1. Position the glass
      1. Using suction cups, place the glass in the correct position.
      2. Check that the entire contact surface of the glass rim is perfectly even.
      3. Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

        HINT

        • Placing matchmarks is only necessary when installing new glass. If it is the reused glass, matchmarks should already be present.
        • When reusing the glass, check and correct the matchmark positions.
        Fig 9: Aligning Matchmarks On Glass And Vehicle Body
        G05776720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        NOTE: Check that the stoppers are attached to the vehicle body correctly.
      4. Using suction cups, remove the glass
    2. Using a brush, apply Primer M to the exposed part of the vehicle body.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Do not apply primer to the adhesive.
      • Throw away any leftover primer.
      • Do not apply too much primer.
    3. Using a brush or sponge, apply Primer G to the contact surface of the glass.
      Fig 10: Identifying Adhesive Correct And Incorrect Installation Position
      G04952196Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 11: Identifying Adhesive Applying Area
      G04952197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard 

      SPECIFIED CONDITION CHART

      Area Specified Condition
      a 6,5 mm (0.258 in.)
      b 7.0 mm (0.276 in.)
      c 3.0 mm (0.118 in.)
      d 4.0 mm (0.157 in.)
      e 8.0 mm (0.315 in.)

      HINT.

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
    4. Apply adhesive to the glass.

      Adhesive: 

      Toyota Genuine Windshield Glass Adhesive or equivalent 

      1. Cut off the tip of the cartridge nozzle as shown in the illustration.

        HINT

        After cutting off the tip, use all adhesive within the time written in the table below

        Usage timeframe 

        TEMPERATURE SPECIFICATION

        Temperature Usage Timeframe
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour 40 minutes
        5°C (41 °F) 8 hours
      2. Load the sealer gun with the cartridge.
      3. Apply adhesive to the glass as shown in the illustration.
      Fig 12: Applying Adhesive To Glass
      G04952198Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard 

      SPECIFIED CONDITION CHART

      Area Specified Condition
      a 12.0 mm (0 472 in.)
      b 8.0 mm (0.315 in.)
      c 6.5 mm (0.258 in.)
      d 3.0 mm (0.118 in.)
    5. Install the glass to the vehicle body
      1. Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim
      2. Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.
        NOTE:
        • Check that the stoppers are attached to the vehicle body correctly.
        • Check that the vehicle body and glass have a small gap between them.
        Fig 13: Positioning Glass To Vehicle Body With Suction Cups
        G04952199Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.
      NOTE: Do not drive the vehicle for the amount of time written in the table below. Minimum time
      TEMPERATURE SPECIFICATION

      Temperature Minimum time prior to driving vehicle
      35°C (95°F) 1 hour 30 minutes
      20°C (68°F) 5 hours
      5°C (41°F) 24 hours
    6. w/Windshield Deicer System.

      Connect the windshield deicer connector

  8. CHECK FOR LEAK AND REPAIR 
    1. Conduct a leak test after the adhesive has completely hardened.
    2. Seal any leaks with auto glass sealer
  9. INSTALL ROOF HEADLINING ASSEMBLY 
    1. Return the roof headlining to its original position Refer to the following procedures (see INSTALLATION ).
  10. INSTALL RAIN SENSOR TAPE  (See INSTALLATION )
  11. INSTALL RAIN SENSOR  (See INSTALLATION )
  12. INSTALL OBJECT RECOGNITION CAMERA  (See INSTALLATION )
  13. INSTALL INNER REAR VIEW MIRROR ASSEMBLY  (See INSPECTION )
  14. INSTALL RAIN SENSOR COVER  (See INSTALLATION )
  15. INSTALL RAIN SENSOR COVER (w/ Driver Monitor Camera)  (See INSTALLATION )
  16. INSTALL MAP LIGHT ASSEMBLY  (See INSTALLATION )
  17. INSTALL ASSIST GRIP SUB-ASSEMBLY  (See INSTALLATION )
  18. INSTALL VISOR HOLDER  (See INSTALLATION )
  19. INSTALL VISOR ASSEMBLY LH  (See INSTALLATION )
  20. INSTALL VISOR ASSEMBLY RH  (See INSTALLATION )
  21. INSTALL VISOR BRACKET COVER  (See INSTALLATION )
  22. INSTALL FRONT PILLAR GARNISH LH  (See INSTALLATION )
  23. INSTALL FRONT PILLAR GARNISH RH  (See INSTALLATION )
  24. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP  (See INSTALLATION )
  25. INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP  (See INSTALLATION )
  26. INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING CLIP  (See INSTALLATION )
  27. INSTALL NO. 2 WINDSHIELD OUTSIDE MOULDING CLIP  (See INSTALLATION )
  28. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP 
    CAUTION: Use the same procedures described for the No. 2 windshield outside moulding clip.
  29. INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING LH  (See INSTALLATION )
  30. INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING RH 

    HINT

    Use the same procedures described for the LH side.

  31. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See INSTALLATION )
  32. INSTALL COWL TOP VENTILATOR LOUVER PROTECTOR LH  (See INSTALLATION )
  33. INSTALL COWL TOP VENTILATOR LOUVER RH  (See INSTALLATION )
  34. INSTALL HOOD TO COWL TOP SEAL  (See INSTALLATION )
  35. INSTALL FRONT FENDER TO COWL SIDE SEAL LH  (See INSTALLATION )
  36. INSTALL FRONT FENDER TO COWL SIDE SEAL RH  (See INSTALLATION )
  37. INSTALL FRONT WIPER ARM LH  (See INSTALLATION )
  38. INSTALL FRONT WIPER ARM RH  (See INSTALLATION )
  39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see INITIALIZATION ).
  40. INSTALL BATTERY SERVICE HOLE COVER LH  (See INSTALLATION )
  41. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY  (See INSTALLATION )
  42. ADJUST OBJECT RECOGNITION CAMERA (w/ Driver Monitor Camera)  (See ADJUSTMENT )
scientia non olet · About LEMON Manuals