LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> LS 600hL >> Repair and Diagnosis >> Engine Mechanical >> Starter >> Starting >> Smart Access System With Push-Button Start >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. READ DATA LIST 

    HINT:

    Using the intelligent tester or Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the power switch OFF.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the power switch ON (IG).
    5. Turn the tester on.
    6. Enter the following menus.
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / (desired system) / DATA LIST.
      2. Techstream - Select. Body Electrical / (desired system) / Data List
    7. According to the display on tester, read the "Data List"
      1. Intelligent tester

        MAIN BODY 

        DATA LIST - MAIN BODY

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        ACC SW Power switch ON (ACC)/ON or OFF ON: Power switch is ON (ACC)
        OFF: Power switch is OFF        		 -
        IGSW Power switch ON (IG)/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        STOP LIGHT SW Stop light switch/ON or OFF ON: Brake pedal is depressed
        OFF: Brake pedal is released        		 -
        ST SW1 Start switch 1/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        ST SW2 Start switch 2/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        STR UNLOCK SW Steering lock condition/ON or OFF ON: Steering is unlocked
        OFF: Steering is locked        		 -
        SHIFT P SIG Shift P position signal/ON or OFF ON: Shift lever in P
        OFF: Shift lever not in P        		 -
        VEHICLE SPD SIG Vehicle speed signal/STOP or RUN STOP: Vehicle is stopped
        RUN: Vehicle is running        		 -
        IG1 RELAY MON1 D-IG1 relay outer relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG2 RELAY MON1 Ignition relay No 2 (IG2) outer relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG1 RELAY MON2 D-IG1 relay inner relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG2 RELAY MON2 Ignition relay No 2 (IG2) inner relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        ACC RELAY MON D-ACC relay monitor/ON or OFF ON: Power switch is ON (ACC)
        OFF: Power switch is OFF        		 -
        LATCH CIRCUIT Latch circuit/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF, ON (ACC)        		 -
        ST REQUEST SIG Hybrid control system start request signal/ ON or OFF ON: STSW signal is ON
        OFF: STSW signal is OFF        		 -
        PWR COND Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON ALL: OFF All relays are OFF
        ACC: ON D-ACC relay is ON
        IG2: ON Ignition relay No 2 (IG2) is ON
        ST: ON STSW signal is ON        		 -
        READY SIG Hybrid control system start request signal monitor/ON or OFF ON: System is ON (READY)
        OFF: System is OFF        		 Power switch pressed and held with shift lever in P

        SMART ACCESS 

        DATA LIST - SMART ACCESS

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        IGSW Power switch/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        UNMATCH V-ID Key number/YES or NO YES: Key number matches
        NO: Key number differs        		 -
        NO RESPONSE Response/YES or NO YES: Response
        NO: No response        		 -
        UNMATCH FORMAT Code format/YES or NO YES: Code format matches
        NO: Code format differs        		 -
        LOW BATTERY Key battery conditions/ON or OFF ON: Battery is depleted
        OFF: Battery is not depleted        		 -
        # CODES Number of diagnosis codes - -
        WRONG CODE ID code/YES or NO YES: ID code matches
        NO: ID code differs        		 -
        WRONG C CODE Challenge code/YES or NO YES: Challenge code matches
        NO: Challenge code differs        		 -
        S CODE CHK S code certification result/NG or OK OK: S code certification result is normal
        NG: S code certification result is abnormal        		 -
        L CODE CHK L code certification result/NG or OK OK: L code certification result is normal
        NG: L code certification result is abnormal        		 -
        IGNITION AREA Key area where hybrid control system can be operated/ALL or FRONT ALL: All areas
        FRONT: Front only        		 -
      2. Techstream

        Main Body 

        DATA LIST - MAIN BODY

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        ACC SW Power switch ON (ACC)/ON or OFF ON: Power switch is ON (ACC)
        OFF: Power switch is OFF        		 -
        IGSW Power switch ON (IG)/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        Stop Light SW Stop light switch/ON or OFF ON: Brake pedal is depressed
        OFF: Brake pedal is released        		 -
        Start Switch 1 Start switch 1/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        Start Switch 2 Start switch 2/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        Steering Unlock Switch Steering lock condition/ON or OFF ON: Steering is unlocked
        OFF: Steering is locked        		 -
        Shift P Signal Shift P position signal/ON or OFF ON: Shift lever in P
        OFF: Shift lever not in P        		 -
        Vehicle Speed Signal Vehicle speed signal/STOP or RUN STOP: Vehicle is stopped
        RUN: Vehicle is running        		 -
        IG1 Relay Monitor (Outside) D-IG1 relay outer relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG2 Relay Monitor (Outside) Ignition relay No 2 (IG2) outer relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG1 Relay Monitor (Inside) D-IG1 relay inner relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        IG2 Relay Monitor (Inside) Ignition relay No 2 (IG2) inner relay monitor/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        ACC Relay Monitor D-ACC relay monitor/ON or OFF ON: Power switch is ON (ACC)
        OFF: Power switch is OFF        		 -
        Latch Circuit Latch circuit/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF, ON (ACC)        		 -
        Starter Request Signal Hybrid control system start request signal/ ON or OFF ON: STSW signal is ON
        OFF: STSW signal is OFF        		 -
        Power Supply Condition Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON ALL: OFF All relays are OFF
        ACC: ON D-ACC relay is ON
        IG2: ON Ignition relay No 2 (IG2) is ON
        ST: ON STSW signal is ON        		 -
        Ready Signal Hybrid control system start request signal monitor/ON or OFF ON: System is ON (READY)
        OFF: System is OFF        		 Power switch pressed and held with shift lever in P

        Smart Access 

        DATA LIST - SMART ACCESS

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Ignition Switch Power switch/ON or OFF ON: Power switch is ON (IG)
        OFF: Power switch is OFF        		 -
        Unmatched Vehicle-ID Key number/YES or NO YES: Key number matches
        NO: Key number differs        		 -
        No Response Response/YES or NO YES: Response
        NO: No response        		 -
        Unmatch Code or Form Code format/YES or NO YES: Code format matches
        NO: Code format differs        		 -
        Key Low Battery Key battery conditions/ON or OFF ON: Battery is depleted
        OFF: Battery is not depleted        		 -
        #Codes Number of diagnosis codes - -
        ID Code Difference (Resp) ID code/YES or NO YES: ID code matches
        NO: ID code differs        		 -
        C Code Difference Challenge code/YES or NO YES: Challenge code matches
        NO: Challenge code differs        		 -
        S Code Check S code certification result/NG or OK OK: S code certification result is normal
        NG: S code certification result is abnormal        		 -
        L Code Check L code certification result/NG or OK OK: L code certification result is normal
        NG: L code certification result is abnormal        		 -
        Ignition Available Area Key area where hybrid control system can be operated/ALL or FRONT All: All areas
        Front: Front only        		 -
  2. PERFORM ACTIVE TEST 

    HINT:

    Using the intelligent tester or Techstream to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests

    1. Warm up the engine.
    2. Turn the power switch OFF.
    3. Connect the intelligent tester or Techstream to the DLC3.
    4. Turn the power switch ON (IG).
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / (desired system) / ACTIVE TEST.
      2. Techstream - Select. Body Electrical / (desired system) / Active Test.
    7. According to the display on tester, perform the "Active Test".
      1. Intelligent tester

        MAIN BODY 

        ACTIVE TEST - MAIN BODY

        Tester Display Test Part Control Range Diagnostic Note
        LIGHTING IND Indicator illumination ON/OFF -
        IND CONDITION Indicator light illumination pattern Green/Amber/No Sig -
        STR LOCK PWR Steering lock ECU power supply ON/OFF -

        SMART ACCESS 

        ACTIVE TEST - SMART ACCESS

        Tester Display Test Part Control Range Diagnostic Note
        FR TRANSMITTER Indoor key antenna (for front) ON / OFF -
        RR TRANSMITTER Indoor key antenna (for rear1) ON / OFF -
        IN_BDR TRNSMTTR Indoor key antenna (for rear2) ON / OFF -
        BDOOR TRNSMTTR Electrical key antenna ON / OFF -
      2. Techstream

        Main Body 

        ACTIVE TEST - MAIN BODY

        Tester Display Test Part Control Range Diagnostic Note
        Indicator for Lighting Indicator illumination ON/OFF -
        Indicator Condition Indicator light illumination pattern Green/Amber/No Sig -
        P Supply for Steering Lock Steering lock ECU power supply ON/OFF -

        Smart Access 

        ACTIVE TEST - SMART ACCESS

        Tester Display Test Part Control Range Diagnostic Note
        Fr-Seat Inside Transmitter Indoor key antenna (for front) ON / OFF -
        Rr-Seat Inside Transmitter Indoor key antenna (for rear1) ON/OFF -
        Inside Trunk/Backdoor Transmitter Indoor key antenna (for rear2) ON / OFF -
        Outside Trunk/Backdoor Transmitter Electrical key antenna ON / OFF -
scientia non olet · About LEMON Manuals