Front Axle Hub: Installation

HINT.

Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side
A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS )

INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH
1. Install the front axle hub to the steering knuckle with the 4 bolts
  Torque: 65 N*m (663 kgf*cm, 48 ft.*lbf)
  
  Fig 1: Locating Front Axle Hub Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL STEERING KNUCKLE SUB-ASSEMBLY LH
1. Connect the splines of the steering knuckle LH and drive shaft assembly.
2. Install the steering knuckle to the front lower ball joint with the 3 bolts.
  Torque: 113 N*m (1152 kgf*cm, 83 ft.*lbf)
  
  Fig 2: Locating Steering Knuckle Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH
1. Install the steering knuckle to the front No. 1 suspension upper arm with the nut.
  Torque: 60 N*m (612 kgf*cm, 44 ft.*lbf)
2. Install new clips.
  NOTE: If it is necessary to align the holes for the clips after installing the nuts, the nuts can be tightened up to 60° more.
  
  Fig 3: Locating Clip And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH
1. Install the steering knuckle to the front No. 2 suspension upper arm with the nut.
  Torque: 60 N*m (612 kgf*cm, 44 ft.*lbf)
2. Install new clips.
  NOTE: If it is necessary to align the holes for the clips after installing the nuts, the nuts can be tightened up to 60° more.
  
  Fig 4: Locating Clip And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT TIE ROD ASSEMBLY LH
1. Connect the tie rod to the steering knuckle with the nut.
  Torque: 60 N*m (612 kgf*cm, 44 ft.*lbf)
2. Install new clips.
  NOTE: If it is necessary to align the holes for the clips after installing the nuts, the nuts can be tightened up to 60° more.
  
  Fig 5: Connecting Tie Rod Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SPEED SENSOR LH
1. Install the speed sensor to the steering knuckle with the bolt.
  Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)
  NOTE:
  - Do not damage the tip of the speed sensor.
  - Do not allow foreign matter to contact the tip or installation area of the speed sensor.
  Fig 6: Identifying Front Speed Sensor Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT SKID CONTROL SENSOR WIRE
1. Connect the front speed sensor connector.
2. Install the sensor clamp to the steering knuckle LH with the bolt.
  Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)
  
  NOTE: Do not twist the skid control sensor wire.
  
  Fig 7: Locating Skid Control Sensor
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT DISC BRAKE DUST COVER LH
1. Install the front disc brake dust cover with the 4 bolts
  Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
  
  Fig 8: Locating Dust Cover Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT DISC (See INSTALLATION )
CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH
1. Install the front disc brake caliper to the steering knuckle with 2 new bolts.
  Torque: 135 N*m (1377 kgf*cm, 100 ft.*lbf)
  NOTE:
  - Do not twist the flexible hose.
  - Make sure the threaded parts are free from foreign matter and are not damaged.
  - Be careful not to overtighten the bolts, as the steering knuckle is made of aluminum.
  Fig 9: Locating Front Disc Brake Caliper Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the flexible hose to the steering knuckle with the bolt.
  Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
  
  Fig 10: Locating Flexible Hose Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT AXLE SHAFT NUT LH (See INSTALLATION )
DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH (See REMOVAL )
REMOVE FRONT DISC (See REMOVAL )
INSPECT FRONT AXLE HUB BEARING LOOSENESS (See ON-VEHICLE INSPECTION )
INSPECT FRONT AXLE HUB RUNOUT (See ON-VEHICLE INSPECTION )
INSTALL FRONT DISC (See INSTALLATION )
CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH
1. Install the front disc brake caliper to the steering knuckle with 2 new bolts
  Torque: 135 N*m (1377 kgf*cm, 100 ft.*lbf)
  NOTE:
  - Do not twist the flexible hose.
  - Make sure the threaded parts are free from foreign matter and are not damaged.
  - Be careful not to overtighten the bolts, as the steering knuckle is made of aluminum.
  Fig 11: Locating Front Disc Brake Caliper Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the flexible hose to the steering knuckle with the bolt.
  Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf)
  
  Fig 12: Locating Flexible Hose Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
STAKE FRONT AXLE SHAFT NUT LH (See INSTALLATION )
INSTALL FRONT WHEEL
Torque: 140 N*m (1428 kgf*cm, 103 ft.*lbf)
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
1. Inspect and adjust the front wheel alignment (see FRONT WHEEL ALIGNMENT )
CHECK ABS SPEED SENSOR SIGNAL
1. Check the speed sensor signal (see TEST MODE PROCEDURE ).
ADJUST VEHICLE HEIGHT
1. Adjust the vehicle height (see ADJUSTMENT )
ADJUST HEADLIGHT ASSEMBLY
1. for LED headlight Adjust the headlight (see ADJUSTMENT ).
2. for HID headlight. Adjust the headlight (see ADJUSTMENT ).
ADJUST OBJECT RECOGNITION CAMERA
1. Adjust the object recognition camera (see ADJUSTMENT ).