LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> LX 570 >> Repair and Diagnosis >> Electrical >> Gauges >> Meter >> Combination Meter >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Combination Meter: Removal

  1. DISABLE AUTOAWAY/RETURN FUNCTION 
    1. Disable the Autoaway/Return function by changing the customize parameter (See CUSTOMIZE PARAMETERS ).
      NOTE: Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      HINT:

      Performing the above operation causes the Autoaway/Return function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.
    3. Turn the engine switch off.
  2. REMOVE ENGINE ROOM SIDE COVER LH  (See REMOVAL )
  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:
    • w/ Navigation System:

      After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
  4. REMOVE INSTRUMENT SIDE PANEL LH 
    1. Place protective tape as shown in the illustration.
    2. Using a molding remover, detach the 6 claws and remove the side panel.
    Fig 1: Identifying Side Panel Claws
    G05765439Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE NO. 1 SWITCH HOLE BASE 
    1. Detach the 5 claws.
    2. Remove the hole base and disconnect the connectors.
    Fig 2: Identifying No. 1 Switch Hole Base Claws
    G05765440Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH 
    1. Detach the 8 claws.
    2. Remove the instrument panel pad and disconnect the connector.
    Fig 3: Identifying Lower Instrument Panel Pad Sub-Assembly LH And Claws
    G05765441Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Detach the 6 claws.
      Fig 4: Identifying Instrument Cluster Finish Panel Sub-Assembly And Claws
      G05765442Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 4 claws.
    3. Remove the finish panel and disconnect the connectors.
    Fig 5: Identifying Finish Panel And Claws
    G05765443Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Detach the 4 claws and remove the register.
    Fig 6: Identifying No. 1 Instrument Panel Register Assembly And Claws
    G05765444Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY 
    1. Detach the 5 claws and remove the register.
    Fig 7: Identifying No. 3 Instrument Panel Register Assembly And Claws
    G05765445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE COMBINATION METER ASSEMBLY 
    1. Remove the 2 screws
      Fig 8: Identifying Combination Meter Assembly And Screw
      G05765446Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 clips.
      Fig 9: Identifying Combination Meter Assembly Clips Location
      G05765447Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the connector and remove the combination meter.
    Fig 10: Locating Combination Meter
    G05765448Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals