LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> RX 350 AWD >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/Window Glass >> Windshield Glass >> Removal
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Windshield Glass: Removal

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation (See PRECAUTION ).
  2. REMOVE FRONT WIPER ARM LH  (See REMOVAL )
  3. REMOVE FRONT WIPER ARM RH  (See REMOVAL )
  4. REMOVE FRONT FENDER TO COWL SIDE SEAL LH 
  5. REMOVE FRONT FENDER TO COWL SIDE SEAL RH 
  6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See REMOVAL )
  7. REMOVE INNER REAR VIEW MIRROR ASSEMBLY  (See REMOVAL )
  8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
  10. REMOVE FRONT PILLAR GARNISH LH  (See REMOVAL )
  11. REMOVE FRONT PILLAR GARNISH RH 
  12. REMOVE MAP LIGHT ASSEMBLY  (See REMOVAL )
  13. REMOVE VISOR ASSEMBLY LH  (See REMOVAL )
  14. REMOVE VISOR ASSEMBLY RH 
  15. REMOVE VISOR HOLDER  (See REMOVAL )
  16. REMOVE ASSIST GRIP SUB-ASSEMBLY  (See REMOVAL )
  17. REMOVE ROOF HEADLINING ASSEMBLY  (See REMOVAL )
  18. REMOVE RAIN SENSOR (w/ Auto Wiper)  (See REMOVAL )
  19. REMOVE WINDSHIELD MOLDING OUTSIDE 
    1. Using a knife, cut off the molding.
      Fig 1: Cutting Off Molding Using Knife
      G05274271Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Do not damage the vehicle body with the knife.
    2. Remove the remaining molding from the vehicle body.

      HINT:

      When removing, make a partial cut, then pull and remove it by hand.

    3. Disconnect the connector (w/ Deicer).
      Fig 2: Identifying Connector
      G05274272Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE WINDSHIELD GLASS 
    1. Pass a piano wire between the vehicle body and glass from the interior.
      Fig 3: Passing Piano Wire Between Vehicle Body & Glass From Interior
      G05274273Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Tie both wire ends to wooden blocks or similar objects.
      Fig 4: Tying Both Wire Ends To Wooden Blocks
      G05274274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • When separating the glass, take care not to damage the paint and the interior and exterior ornaments.
      • To prevent the safety pad from being scratched when removing the glass, place a plastic sheet between the piano wire and safety pad.

      HINT:

      Apply protective tape to the outer surface to prevent the surface from being scratched.

    3. Cut off the adhesive by pulling the piano wire around the glass.
    4. Disengage the stoppers.
    5. Using a suction cup, remove the glass.
      NOTE: Leave as much adhesive on the vehicle body as possible when removing the glass.
  21. REMOVE WINDSHIELD GLASS RETAINER 
    1. Remove the windshield glass retainer.
  22. REMOVE WINDSHIELD GLASS NO.2 STOPPER 
    1. Using a scraper, remove the windshield glass No.2 stoppers.
  23. REMOVE WINDSHIELD GLASS NO.1 STOPPER 
    1. Remove the windshield glass Not stoppers.
  24. CLEAN WINDSHIELD GLASS 
    1. Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.
    2. Clean the outer circumference of the glass with a non-residue solvent.
      NOTE:
      • Do not touch the glass surface after cleaning it.
      • Be careful not to damage the glass.
      • Even if using anew glass, clean the glass with a non-residue solvent.
        Fig 5: Cleaning Windshield Glass
        G04952185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals