Front Axle Hub: Installation

HINT:

• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
• A bolt without a torque specification is shown in the standard bolt chart (see SPECIFIED TORQUE FOR STANDARD BOLTS ).

1. INSTALL FRONT AXLE HUB BEARING LH 
   1. Using SST and a press, press in a new bearing to the steering knuckle.

      SST 09309-36010, 09950-60020 (09951-00720), 09950-70010 (09951-07150) 

      NOTE: If the inner race and balls come loose from the bearing outer race, make sure to install them in the same position as before.
   Fig 1: Pressing Bearing To Steering Knuckle

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL FRONT AXLE HUB HOLE SNAP RING LH 
   1. Using snap ring pliers, install the snap ring.
3. INSTALL FRONT AXLE HUB OIL SEAL LH 
   1. Install the inner race (outside).
   2. Using SST and a hammer, tap in a new oil seal until it is flush with the end surface of the steering knuckle.

      SST 09608-32010 

   3. Coat the oil seal lip with MP grease.
   Fig 2: Tapping In Front Axle Hub Oil Seal LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. INSTALL FRONT DISC BRAKE DUST COVER LH 
   1. Install the brake dust cover to the steering knuckle with the 4 bolts.

      Torque: 8.3 N*m (85 kgf*cm, 74 in.*lbf) 

5. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH 
   1. Using SST and a press, press in the axle hub to the steering knuckle.

      SST 09316-60011 (09316-00011,09316-00071), 09608-32010 

   Fig 3: Pressing Axle Hub To Steering Knuckle With SST

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. INSTALL FRONT SKID CONTROL ROTOR 
   NOTE: Do not scratch the serrations of the sensor rotor.
7. INSTALL FRONT AXLE HUB NUT LH 
   1. Using a 36 mm socket wrench, install a new axle hub lock nut.

      Torque: 199 N*m (2,030 kgf*cm, 147 ft.*lbf) 

   2. Using a chisel and hammer, stake the lock nut.
   Fig 4: Identifying Axle Hub Lock Nut

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. INSTALL FRONT AXLE HUB GREASE CAP LH 
   1. Using a screwdriver and hammer, tap in the grease cap to the steering knuckle.
9. INSTALL STEERING KNUCKLE ASSEMBLY LH 
   1. Connect the steering knuckle to the lower ball joint with the 2 bolts.

      Torque: 113 N*m (1,150 kgf*cm, 83 ft.*lbf) 

   2. Connect the steering knuckle to the upper suspension arm with the nut.

      Torque: 87 N*m (887 kgf*cm, 64 ft.*lbf) 

   3. Install the clip.
   Fig 5: Identifying Steering Knuckle To Lower Ball Joint And Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. INSTALL FRONT BRAKE DISC 
11. CONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH 
    1. Connect the brake cylinder to the steering knuckle with the 2 bolts.

       Torque: 118 N*m (1,203 kgf*cm, 87 ft.*lbf) 

    Fig 6: Identifying Brake Cylinder To Steering Knuckle And Bolts

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
12. CONNECT FRONT SPEED SENSOR LH (See  INSTALLATION  ) 
13. INSTALL FRONT WHEEL 

    Torque: 103 N*m (1,050 kgf*cm, 76 ft.*lbf) 

14. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT 
    1. Inspect and adjust the front wheel alignment (see FRONT WHEEL ALIGNMENT ).
15. CHECK ABS SPEED SENSOR SIGNAL 
    1. Check the ABS speed sensor signal (see DIAGNOSIS SYSTEM ).