Problem Symptoms Table
If there are no DTCs output and the problem still occurs, check the circuits for each problem symptom in the order given in the table below and proceed to the relevant troubleshooting page.
HINT:
- Inspect the fuse and relay before investigating the suspected areas as shown in the table below.
- Inspect each malfunction circuit in numerical order for the corresponding symptom.
VEHICLE STABILITY CONTROL SYSTEM:
| Symptom | Suspected Area | See page |
|---|---|---|
| ABS, BA and/or EBD does not operate | 1. Check the DTC again and make sure that the normal system code is output. | Refer to DTC CHECK / CLEAR |
| 2. IG power source circuit | Refer to DTC C1241/41: Low Battery Positive Voltage | |
| 3. Front speed sensor circuit | Refer to DTC C0200/31: Front Speed Sensor RH Circuit; DTC C0205/32: Front Speed Sensor LH Circuit; DTC C1271/71: Low Output Signal of Front Speed Sensor RH (Test Mode DTC); DTC C1272/72: Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | |
| 4. Rear speed sensor circuit | Refer to DTC C0210/33: Rear Speed Sensor RH Circuit; DTC C0215/34: Rear Speed Sensor LH Circuit; DTC C1273/73: Low Output Signal of Rear Speed Sensor RH (Test Mode DTC); DTC C1274/74: Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | |
| 5. Check the brake actuator assembly with Techstream. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | Refer to ON-VEHICLE INSPECTION | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | Refer to REMOVAL | |
| ABS, BA and/or EBD does not operate efficiently | 1. Check the DTC again and make sure that the normal system code is output. | Refer to DTC CHECK / CLEAR |
| 2. Front speed sensor circuit | Refer to DTC C0200/31: Front Speed Sensor RH Circuit; DTC C0205/32: Front Speed Sensor LH Circuit; DTC C1271/71: Low Output Signal of Front Speed Sensor RH (Test Mode DTC); DTC C1272/72: Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | |
| 3. Rear speed sensor circuit | Refer to DTC C0210/33: Rear Speed Sensor RH Circuit; DTC C0215/34: Rear Speed Sensor LH Circuit; DTC C1273/73: Low Output Signal of Rear Speed Sensor RH (Test Mode DTC); DTC C1274/74: Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | |
| 4. Stop light switch circuit | Refer to DTC C1249/49: Open in Stop Light Switch Circuit | |
| 5. Check the brake actuator assembly with Techstream. (Check brake actuator assembly operation using the Active Test function.) If abnormal, check the hydraulic circuit for leakage. | Refer to ON-VEHICLE INSPECTION | |
| 6. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | Refer to REMOVAL | |
| ABS sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | Refer to DTC CHECK / CLEAR |
| 2. TC and CG terminal circuit | Refer to TC and CG Terminal Circuit | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | Refer to REMOVAL | |
| ABS warning light abnormal (Remains on) | 1. ABS warning light circuit | Refer to ABS Warning Light Remains ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| ABS warning light abnormal (Does not come on) | 1. ABS warning light circuit | Refer to ABS Warning Light does not Come ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| BRAKE warning light abnormal (Remains on) | 1. BRAKE warning light circuit | Refer to Brake Warning Light Remains ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| BRAKE warning light abnormal (Does not come on) | 1. BRAKE warning light circuit | Refer to Brake Warning Light does not Come ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| VSC and/or TRAC does not operate | 1. Check the DTC again and make sure that the normal system code is output. | Refer to DTC CHECK / CLEAR |
| 2. IG power source circuit | Refer to DTC C1241/41: Low Battery Positive Voltage | |
| 3. Check the hydraulic circuit for leakage | - | |
| 4. Front speed sensor circuit | Refer to DTC C0200/31: Front Speed Sensor RH Circuit; DTC C0205/32: Front Speed Sensor LH Circuit; DTC C1271/71: Low Output Signal of Front Speed Sensor RH (Test Mode DTC); DTC C1272/72: Low Output Signal of Front Speed Sensor LH (Test Mode DTC) | |
| 5. Rear speed sensor circuit | Refer to DTC C0210/33: Rear Speed Sensor RH Circuit; DTC C0215/34: Rear Speed Sensor LH Circuit; DTC C1273/73: Low Output Signal of Rear Speed Sensor RH (Test Mode DTC); DTC C1274/74: Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) | |
| 6. Yaw rate and acceleration sensor circuit | Refer to DTC C1232/32: Stuck in Acceleration Sensor; DTC C0371/71: Yaw Rate Sensor (Test Mode DTC); DTC C1234/34: Yaw Rate Sensor Malfunction; DTC C1243/43: Acceleration Sensor Stuck Malfunction; DTC C1244/44: Open or Short in Acceleration Sensor Circuit; DTC C1245/45: Acceleration Sensor Output Malfunction; DTC C1279/79: Acceleration Sensor Output Voltage Malfunction (Test Mode DTC); DTC C1381/97: Acceleration Sensor Power Supply Voltage Malfunction | |
| 7. Steering angle sensor circuit | Refer to DTC C1231/31: Steering Angle Sensor Circuit Malfunction | |
| 8. If the symptoms still occur even after the above circuits in suspected areas have been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | Refer to REMOVAL | |
| VSC sensor DTC check cannot be done | 1. Check the DTC again and make sure that the normal system code is output. | Refer to DTC CHECK / CLEAR |
| 2. TC and CG terminal circuit | Refer to TC and CG Terminal Circuit | |
| 3. If the symptoms still occur even after the above circuit in suspected areas has been inspected and proved to be normal, replace the brake actuator assembly (skid control ECU). | Refer to REMOVAL | |
| VSC warning (multi information display) abnormal (Remains on) | 1. VSC warning light circuit | Refer to VSC Warning Light Remains ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| VSC warning (multi information display) abnormal (Does not come on) | 1. VSC warning light circuit | Refer to VSC Warning Light does not Come ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| SLIP indicator light abnormal (Remains on) | 1. SLIP indicator light circuit | Refer to Slip Indicator Light Remains ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| SLIP indicator light abnormal (Does not come on) | 1. SLIP indicator light circuit | Refer to Slip Indicator Light does not Come ON |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| Sensor check cannot be done | 1. TS and CG terminal circuit | Refer to TS and CG Terminal Circuit |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL | |
| Skid control buzzer abnormal | 1. Skid control buzzer circuit | Refer to Skid Control Buzzer Circuit |
| 2. Brake actuator assembly (Skid control ECU) | Refer to REMOVAL |