LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2010 >> GS 350 AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostics - Introduction) >> SFI System >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT: 

    By reading the Data List displayed on the Techstream, you can check values, including those of the switches, sensors and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

    NOTE:

    In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the Techstream on.
    6. Select the following menu items: Powertrain / Engine / Data List.
    7. Check the values by referring to the table below.
    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Vehicle Speed Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h    		 Actual vehicle speed Speed indicated on speedometer
    Engine Speed Engine speed:
    Min.: 0 RPM, Max.: 16383 RPM:    		 550 to 800 RPM: Idling -
    Calculate Load Calculated load by ECM:
    Min.: 0%, Max.: 100%
    • 15.0 to 35.0%: Idling
    • 10.0 to 30.0%: Running without load (2000 RPM)
    		 -
    Vehicle Load Vehicle load:
    Min.: 0%, Max.: 25700%    		 Actual vehicle load Load percentage in terms of maximum intake air flow amount
    MAF Air flow rate from MAF meter:
    Min.: 0 gm/s, Max.: 655.35 gm/s    		 2.7 to 3.7 gm/s: Idling
    8.8 to 9.8 gm/s: 2000 RPM    		 If value approximately 0.0 gm/s:
    • Mass air flow meter power source circuit open
    • VG circuit open or shorted

    If value 271.0 gm/s or more:
    • E2G circuit open
    Atmosphere Pressure Atmospheric pressure:
    Min.: 0 kPa, Max.: 255 kPa    		 Equivalent to atmospheric pressure (absolute pressure) -
    Coolant Temp Engine coolant temperature:
    Min.: -40°C (-40°F), Max.: 140°C (284°F)    		 80 to 105°C (176 to 221°F):
    After warming up
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F) or higher: sensor circuit shorted
    Intake Air Intake air temperature:
    Min.: -40°C (-40°F), Max.: 140°C (284°F)    		 Equivalent to ambient air temperature
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F) or higher: sensor circuit shorted
    Ambient Temperature Ambient temperature:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)    		 Actual atmospheric temperature -
    Engine Run Time Engine run time:
    Min.: 0 s,
    Max.: 65535 s    		 Time after engine start -
    Initial Engine Coolant Temp Initial engine coolant temperature:
    Min.: -40°C (-40°F),
    Max.: 119.3°C (246.8°F)    		 Close to ambient air temperature Service data
    Initial Intake Air Temp Initial intake air temperature:
    Min.: -40°C (-40°F),
    Max.: 119.3°C (246.8°F)    		 Close to ambient air temperature Service data
    Battery Voltage Battery voltage:
    Min.: 0, Max.: 65.535 V    		 9 to 14 V: Idling -
    Accelerator Position Accelerator pedal position:
    Min.: 0%, Max.: 399.9%    		 Actual accelerator pedal position -
    Accel Sens. No. 1 Volt % Absolute accelerator pedal position No. 1:
    Min.: 0%, Max.: 100%    		 10 to 25%: Accelerator pedal released
    60 to 90%: Accelerator pedal fully depressed    		 -
    Accel Sens. No. 2 Volt % Absolute accelerator pedal position No. 2:
    Min.: 0%, Max.: 100%    		 20 to 45%: Accelerator pedal released
    80 to 100%: Accelerator pedal fully depressed    		 -
    Accel Sensor Out No. 1 Accelerator pedal position sensor No. 1 voltage:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed    		 -
    Accel Sensor Out No. 2 Accelerator pedal position sensor No. 2 voltage:
    Min.: 0 V, Max.: 4.98 V    		 1.2 to 2.0 V: Accelerator pedal released
    3.4 to 4.8 V: Accelerator pedal fully depressed    		 -
    Accelerator Idle Position Whether or not accelerator pedal position sensor detecting idle:
    ON or OFF    		 ON: Idling -
    Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1:
    Min.: 0 deg, Max.: 124.5 deg    		 - Electronic throttle control system service data
    Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2:
    Min.: 0 deg Max.: 124.5 deg    		 - Electronic throttle control system service data
    Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
    Min.: 0%, Max.: 100%
    • 10 to 22%: Accelerator pedal released
    • 64 to 96%: Accelerator pedal fully depressed
    		 Valve calculated based on the voltage at terminal VTA1
    Throttle Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
    Min.: 0%, Max.: 100%
    • 42 to 62%: Accelerator pedal released
    • 92 to 100%: Accelerator pedal fully depressed
    		 Valve calculated based on the voltage at terminal VTA2
    ST1 Brake pedal signal:
    ON or OFF    		 OFF: Brake pedal released -
    System Guard System guard:
    ON or OFF    		 - ETCS service data
    Open Side Malfunction Open side malfunction:
    ON or OFF    		 - Electric throttle control system service data
    Throttle Idle Position Whether or not throttle position sensor detecting idle:
    ON or OFF
    • ON: Accelerator pedal released
    • OFF: Accelerator pedal fully depressed
    		 -
    Throttle Require Position Throttle requirement position:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 1.1 V: Idling -
    Throttle Sensor Position*1 Throttle sensor position:
    Min.: 0%, Max.: 100%
    • 0%: Accelerator pedal released
    • 50 to 80%: Accelerator pedal fully depressed
    		 Recognition value for throttle opening angle on ECM
    Throttle Position No. 1 Throttle position No. 1:
    Min.: 0 V, Max.: 4.98 V
    • 0.5 to 1.1 V: Accelerator pedal released
    • 3.2 to 4.8 V: Accelerator pedal fully depressed
    • 0.6 to 1.4 V: fail-safe operating
    		 -
    Throttle Position No. 2 Throttle position No. 2:
    Min.: 0 V, Max.: 4.98 V
    • 2.1 to 3.1 V: Accelerator pedal released
    • 4.6 to 5.0 V: Accelerator pedal fully depressed
    • 2.1 to 3.1 V: fail-safe operating
    		 -
    Throttle Position Command Throttle position command value:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 4.8 V -
    Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.98 V    		 0.6 to 1.4 V ETCS service data
    Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.98 V    		 1.7 to 2.5 V ETCS service data
    Throttle Motor Current Throttle actuator current:
    Min.: 0 A, Max.: 19.9 A    		 0 to 3.0 A: Idling ETCS service data
    Throttle Motor DUTY Throttle actuator:
    Min.: 0%, Max.: 100%    		 10 to 22%: Idling after engine warmed up ETCS service data
    Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
    Min.: 0%, Max.: 255%    		 0 to 40%: Idling ETCS service data
    Throttle Motor Duty (Close) Throttle actuator duty ratio (close):
    Min.: 0%, Max.: 255%    		 0 to 40%: Idling ETCS service data
    Throttle Fully Close Learn Throttle valve fully closed
    (learned value):
    Min.: 0 V, Max.: 4.98 V    		 0.4 to 1.0 V: Accelerator pedal released -
    +BM Voltage +BM voltage:
    Min.: 0 V, Max.: 79.998 V    		 11 to 14 V: Engine switch on (IG) and system normal ETCS service data
    Actuator Power Supply Actuator power supply:
    ON or OFF    		 ON: Idling ETCS service data
    Fuel Press Fuel pressure:
    Min.: 0 kPa Max.: 655350 kPa    		 3 to 5 MPa (31 to 51 kgf/cm2 , 435 to 725 psi): Idling
    7 to 9 MPa (71 to 92 kgf/cm2 , 1015 to 1305 psi): 2000 RPM    		 -
    Injector (Port) Injection period of No. 1 cylinder:
    Min.: 0 μs, Max.: 65535 μs    		 700 to 1600 μs: Idling -
    Injection Volum (Cylinder 1) Injection volume (Cylinder 1):
    Min.: 0 ml, Max.: 2.047 ml    		 0.05 to 0.15 ml: idling Quantity of fuel injection volume for 10 times
    Fuel Pump Speed Control Fuel pump speed control status:
    ON or OFF    		 Idling: ON Active Test support data
    Fuel Pump/Speed Status Fuel pump/status:
    ON or OFF    		 ON: Cranking Active Test support data
    Vacuum Pump Key-off EVAP system leak detection pump status:
    ON or OFF    		 - Active Test support data
    Combination Status (D4) Combination status:
    FC, Stratify, Lean Burn, Stoich 1, Stoich 2    		 Stoich 1 -
    Fuel Pressure Target Value Target fuel pressure:
    Min.: 0 MPa, Max.: 65.535 MPa    		 3 to 5 MPa (31 to 51 kgf/cm2 , 435 to 725 psi): Idling
    6 to 10 MPa (61 to 102 kgf/cm2 , 870 to 1451 psi): 2500 RPM (No load)    		 -
    Fuel Pump Duty (D4) Fuel pump duty (D4):
    Min.: 0%, Max.: 127.5%    		 0 to 40%: Idling -
    HP FP Discharge Rate Fuel volume required by the high-pressure fuel pump:
    Min.: 0 ml, Max.: 2.047 ml    		 - -
    Injection Way Injection mode:
    Port or Direct or Either    		 - -
    Injection Switching Status Prohibition of changing the D-4S injection method:
    OK or NG    		 - -
    Injection Timing (D4) Injection timing (D4):
    Min.: -3276.8 °CA, Max.: 3276.7 °CA    		 320 to 340 °CA: Idling -
    Injection Time (D4) Injection time (D4):
    Min.: 0 μs, Max.: 65535 μs    		 700 to 2000 μs: Idling -
    Evap (Purge) VSV Purge VSV control duty:
    Min.: 0%, Max.: 100%    		 0 to 20%: Idling Order signal from ECM
    Evap Purge Flow Purge flow:
    Min.: 0%, Max.: 399.9%    		 0 to 10%: Idling Service data
    Purge Density Learn Value Learning value of purge density:
    Min.: -200, Max.: 199.993    		 -35 to 1%: Idling Service data
    Vapor Pressure Pump Vapor pressure:
    Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10183.28 mmHg)    		 Approximately 100 kPa (750 mmHg) (absolute): Engine switch on (IG) EVAP system pressure monitored by canister pressure sensor
    Vapor pressure (calculated) Vapor pressure (calculated):
    Min.: -720.896 kPa (-5408.07 mmHg), Max.: 720.894 kPa (5407.91 mmHg)    		 Approximately 100 kPa (750 mmHg) (absolute): Engine switch on (IG) EVAP system pressure monitored by canister pressure sensor
    EVAP System Vent Valve Key-off EVAP system vent valve status:
    ON or OFF    		 - Active Test support data
    EVAP Purge VSV VSV status for EVAP control:
    ON or OFF    		 - -
    Purge Cut VSV Duty Purge cut VSV duty:
    Min.: 0%, Max.: 399.9%    		 - -
    Target Air-Fuel Ratio Air-fuel ratio:
    Min.: 0%, Max.: 399.9%    		 - -
    AF Lambda B1S1 Short-term fuel trim associated with Bank 1 Sensor 1:
    Min.: 0, Max.: 1.99
    • Value less than 1 (0.000 to 0.999) = Rich
    • Stoichiometric air-fuel ratio = 1
    • Value greater than 1 (1.001 to 1.999) = Lean
    		 -
    AF Lambda B2S1 Short-term fuel trim associated with Bank 2 Sensor 1:
    Min.: 0, Max.: 1.99
    • Value less than 1 (0.000 to 0.999) = Rich
    • Stoichiometric air-fuel ratio = 1
    • Value greater than 1 (1.001 to 1.999) = Lean
    		 -
    AFS Voltage B1 S1 A/F sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 7.99 V    		 2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    AFS Voltage B2 S1 A/F sensor output voltage for bank 2 sensor 1:
    Min.: 0 V, Max.: 7.99 V    		 2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    AFS Current B1 S1 A/F sensor output current for bank 1 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA    		 - Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check current output of sensor
    AFS Current B2 S1 A/F sensor output current for bank 2 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA    		 - Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check current output of sensor
    O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V    		 0.1 to 0.9 V:
    Driving at 44 mph (70 km/h)    		 Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    O2S B2 S2 Heated oxygen sensor output voltage for bank 2 sensor 2:
    Min.: 0 V, Max.: 1.275 V    		 0.1 to 0.9 V:
    Driving at 44 mph (70 km/h)    		 Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
    O2S Impedance B1S2 Sub heated oxygen sensor impedance (Bank 1, Sensor 2):
    Min.: 0 Ω, Max.: 21247.67 Ω    		 - -
    O2S Impedance B2S2 Sub heated oxygen sensor impedance (Bank 2, Sensor 2):
    Min.: 0 Ω, Max.: 21247.67 Ω    		 - -
    O2 Heater B1S2 Heated oxygen sensor heater for bank 1 sensor 2:
    Not Act or Active    		 - -
    O2 Heater B2S2 Heated oxygen sensor heater for bank 2 sensor 2:
    Not Act or Active    		 - -
    O2 Heater Curr Val B1S2 Heated oxygen sensor current for bank 1 sensor 2:
    Min.: 0 A, Max.: 4.9 A    		 - -
    O2 Heater Curr Val B2S2 Heated oxygen sensor current for bank 2 sensor 2:
    Min.: 0 A, Max.: 4.9 A    		 - -
    Short FT #1 Short-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1 Long-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -30 to 30% Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Total FT #1 Total fuel trim of bank 1
    Average value for fuel trim system of bank 1:
    Min.: -0.5, Max.: 0.496    		 -0.28 to 0.2: Idling -
    Short FT #2 Short-term fuel trim of bank 2:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #2 Long-term fuel trim of bank 2:
    Min.: -100%, Max.: 99.2%    		 -30 to 30% Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Total FT #2 Total fuel trim of bank 2
    Average value for fuel trim system of bank 2:
    Min.: -0.5, Max.: 0.496    		 -0.28 to 0.2: Idling -
    Fuel System Status #1 Fuel system status (bank 1):
    OL or CL or OLDrive or OLFault or CLFault    		 CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop
    • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    • OLDrive: Open loop due to driving conditions (fuel enrichment)
    • OLFault: Open loop due to detected system fault
    • CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
    Fuel System Status #2 Fuel system status (bank 2):
    OL or CL or OLDrive or OLFault or CLFault    		 CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop
    • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    • OLDrive: Open loop due to driving conditions (fuel enrichment)
    • OLFault: Open loop due to detected system fault
    • CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
    IGN Advance Ignition timing advance for No. 1 cylinder:
    Min.: -64 deg., Max.: 63.5 deg.    		 BTDC 5 to 22°: Idling -
    Knock Feedback Value Feedback value of knocking:
    Min: -1024°CA, Max.: 1023.9°CA    		 -25 to 0°CA:
    Driving at 44 mph (70 km/h)    		 Service data
    Knock Correct Learn Value Correction learning value of knocking:
    Min: -1024°CA, Max.: 1023.9°CA    		 3 to 28°CA:
    Driving at 44 mph (70 km/h)    		 Service data
    VVT Control Status #1 VVT control (bank 1) status:
    ON or OFF    		 - -
    VVT Control Status #2 VVT control (bank 2) status:
    ON or OFF    		 - -
    VVT Aim Angle #1*2 VVT aim angle (bank 1):
    Min.: 0%, Max.: 399.9%    		 0%: Idling VVT duty signal value during intrusive operation
    VVT Change Angle #1*2 VVT change angle (bank 1):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling Displacement angle during intrusive operation
    VVT OCV Duty #1*2 VVT OCV operation duty (bank 1):
    Min.: 0%, Max.: 399.9%    		 10 to 40%: Idling Requested duty value for intrusive operation
    VVT Aim Angle #2*2 VVT aim angle (bank 2):
    Min.: 0%, Max.: 399.9%    		 0%: Idling VVT duty signal value during intrusive operation
    VVT Change Angle #2 VVT change angle (bank 2):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling Displacement angle during intrusive operation
    VVT OCV Duty #2*2 VVT OCV operation duty (bank 2):
    Min.: 0%, Max.: 399.9%    		 10 to 40%: Idling Requested duty value for intrusive operation
    VVT Ex Hold Lrn Val #1*2 VVT exhaust hold duty ratio learning value (bank 1):
    Min.: 0%, Max.: 399.9%    		 40 to 65%: Idling -
    VVT Ex Chg Angle #1*2 VVT exhaust change angle (bank 1):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling -
    VVT Ex OCV Duty #1*2 VVT exhaust OCV duty (bank 1):
    Min.: 0%, Max.: 399.9%    		 10 to 40%: Idling -
    VVT Ex Hold Lrn Val #2*2 VVT exhaust hold duty ratio learning value (bank 2):
    Min.: 0%, Max.: 399.9%    		 40 to 65%: Idling -
    VVT Ex Chg Angle #2*2 VVT exhaust change angle (bank 2):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling -
    VVT Ex OCV Duty #2*2 VVT exhaust OCV duty (bank 2):
    Min.: 0%, Max.: 399.9%    		 10 to 40%: Idling -
    VN Turbo Type Variable nozzle turbo type:
    Not Avl or Commo or Vacuum or CAN Com    		 Not Avl (Unused) -
    Catalyst Temp B1 S1 Catalyst temperature (bank 1, sensor 1):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756°F)    		 - -
    Catalyst Temp B2 S1 Catalyst temperature (bank 2, sensor 1):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756°F)    		 - -
    Catalyst Temp B1 S2 Catalyst temperature (bank 1, sensor 2):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756°F)    		 - -
    Catalyst Temp B2 S2 Catalyst temperature (bank 2, sensor 2):
    Min.: -40°C (-40°F),
    Max.: 6513.5°C (11756°F)    		 - -
    Starter Signal Starter signal:
    Close or Open    		 ON: Open -
    Starter Control Starter switch status:
    ON or OFF    		 ON: Cranking -
    Power Steering Signal Record Power steering signal:
    ON or OFF    		 ON: Power steering operation -
    Starter Relay Starter relay status:
    ON or OFF    		 Starter relay status:
    ON or OFF    		 -
    ACC Relay ACC relay status:
    ON or OFF    		 ON: Cranking -
    Neutral Position SW Signal Park/neutral position switch assembly status:
    ON or OFF    		 ON: P or N position -
    Stop Light Switch Stop light switch assembly:
    ON or OFF    		 ON: Brake pedal depressed -
    A/C Signal A/C signal:
    ON or OFF    		 ON: A/C on -
    Idle Up Signal Idle up signal:
    ON or OFF    		 - -
    Fuel Cut Condition Fuel-cut condition:
    ON or OFF    		 ON: Any fuel cut operation executed -
    Immobiliser Communication Immobiliser communication:
    ON or OFF    		 - OFF: Communication malfunctioning, or engine immobiliser system set
    ON: Communication normal
    Closed Throttle Position SW Closed throttle position switch:
    ON or OFF
    • ON: Throttle fully closed
    • OFF: Throttle open
    		 -
    Engine Oil Pressure SW Engine oil pressure switch signal:
    ON or OFF    		 ON: Oil pressure warning light turned ON -
    Check Mode Check mode:
    OFF or ON    		 ON: Check mode ON Refer to CHECK MODE PROCEDURE 
    SPD Test Result Check mode result for vehicle speed sensor:
    Compl or Incompl    		 - -
    Misfire Test Result Check mode result for misfire monitor:
    Complete or Incomplete    		 - -
    OXS1 Test Result Check mode result for HO2 sensor (bank 1):
    Complete or Incomplete    		 - -
    OXS2 Test Result Check mode result for HO2 sensor (bank 2):
    Complete or Incomplete    		 - -
    A/F Test Results #2 Check mode result for air-fuel ratio sensor (bank 2):
    Complete or Incomplete    		 - -
    A/F Test Results #1 Check mode result for air-fuel ratio sensor (bank 1):
    Complete or Incomplete    		 - -
    Complete Parts Monitor Comprehensive component monitor:
    Not Avl or Avail    		 - Comprehensive Component Monitor
    Fuel System Monitor Fuel system monitor:
    Not Avl or Avail    		 - Fuel System Monitor
    Misfire Monitor Misfire monitor:
    Not Avl or Avail    		 - Misfire Monitor
    EGR/VVT Monitor EGR monitor:
    Not Avl or Avail    		 - -
    EGR/VVT Monitor EGR monitor:
    Compl or Incmpl    		 - -
    O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Not Avl or Avail    		 - -
    O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Complete or Incomplete    		 - -
    O2S (A/FS) Monitor O2S (A/FS) monitor:
    Not Avl or Avail    		 - -
    O2S (A/FS) Monitor O2S (A/FS) monitor:
    Complete or Incomplete    		 - -
    A/C Monitor A/C monitor:
    Not Avl or Avail    		 - -
    A/C Monitor A/C Monitor:
    Compl or Incmpl    		 - -
    2nd Air Monitor Secondary air injection system monitor:
    Not Avl or Avail    		 - -
    2nd Air Monitor Secondary air injection system monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor EVAP monitor:
    Not Avl or Avail    		 - -
    EVAP Monitor EVAP monitor:
    Complete or Incomplete    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Not Avl or Avail    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Compl or Incmpl    		 - -
    Catalyst Monitor Catalyst monitor:
    Not Avl or Avail    		 - -
    Catalyst Monitor Catalyst monitor:
    Complete or Incomplete    		 - -
    Component Monitor ENA Comprehensive component monitor:
    Unable or Enable    		 - -
    Component Monitor CMPL Comprehensive component monitor:
    Complete or Incomplete    		 - -
    Fuel System Monitor ENA Fuel system monitor:
    Unable or Enable    		 - -
    Fuel System Monitor CMPL Fuel system monitor:
    Complete or Incomplete    		 - -
    Misfire Monitor ENA Misfire monitor:
    Unable or Enable    		 - -
    Misfire Monitor CMPL Misfire monitor:
    Complete or Incomplete    		 - -
    EGR/VVT Monitor ENA EGR monitor:
    Unable or Enable    		 - -
    EGR/VVT Monitor CMPL EGR monitor:
    Compl or Incmpl    		 - -
    Heater Monitor ENA O2S (A/FS) heater monitor:
    Unable or Enable    		 - -
    Heater Monitor CMPL O2S (A/FS) heater monitor:
    Complete or Incomplete    		 - -
    O2S (A/FS) Monitor ENA O2S (A/FS) monitor:
    Unable or Enable    		 - -
    O2S (A/FS) Monitor CMPL O2S (A/FS) monitor:
    Complete or Incomplete    		 - -
    A/C Monitor ENA A/C Monitor ENA:
    Unable or Enable    		 - -
    A/C Monitor CMPL A/C Monitor CMPL:
    Complete or Incomplete    		 - -
    2nd Air Monitor ENA Secondary air injection system monitor:
    Unable or Enable    		 - -
    2nd Air Monitor CMPL Secondary air injection system monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor ENA EVAP monitor:
    Unable or Enable    		 - -
    EVAP Monitor CMPL EVAP monitor:
    Complete or Incomplete    		 - -
    Heated Cat Monitor ENA Heated Cat Monitor ENA:
    Unable or Enable    		 - -
    Heated Cat Monitor CMPL Heated Cat Monitor CMPL:
    Complete or Incomplete    		 - -
    Catalyst Monitor ENA Catalyst monitor:
    Unable or Enable    		 - -
    Catalyst Monitor CMPL Catalyst monitor:
    Complete or Incomplete    		 - -
    TC Terminal TC terminal status:
    ON or OFF    		 - -
    # Codes (Include History) #Codes:
    Min.: 0, Max.: 255    		 - Number of detected DTCs
    MIL MIL status:
    ON or OFF    		 ON: MIL ON -
    MIL ON Run Distance MIL ON run distance:
    Min.: 0 Km,
    Max.: 65535 Km    		 Distance after DTC detected -
    Running Time from MIL ON Running time from MIL ON:
    Min.: 0 min,
    Max.: 65535 min    		 Equivalent to running time after MIL ON -
    Time after DTC Cleared Time after DTC cleared:
    Min.: 0 min,
    Max.: 65535 min    		 Equivalent to time after DTCs erased -
    Distance from DTC Cleared Distance after DTC cleared:
    Min.: 0 km, Max.: 65535 km    		 Equivalent to drive distance after DTCs erased -
    Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared:
    Min.: 0, Max.: 255    		 - Number of warm-up cycles after DTC cleared
    Dist Batt Cable Disconnect Distance from battery cable disconnected:
    Min.: 0 Km, Max.: 65535 Km    		 - -
    IG OFF Elapesd Time Time after engine switch off:
    Min.: 0 min, Max.: 655350 min    		 - -
    OBD Requirements OBD requirement OBD2 -
    Number of Emission DTC Emission related DTCs - Number of emission related DTCs
    TC and TE1 TC and TE1 terminals of DLC3:
    ON or OFF    		 - Active Test support data
    Ignition Trig. Count Ignition counter:
    Min.: 0, Max.: 65535    		 - -
    Cylinder #1 Misfire Count Misfire ratio of cylinder 1:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #2 Misfire Count Misfire ratio of cylinder 2:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #3 Misfire Count Misfire ratio of cylinder 3:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #4 Misfire Count Misfire ratio of cylinder 4:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #5 Misfire Count Misfire ratio of cylinder 5:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #6 Misfire Count Misfire ratio of cylinder 6:
    Min.: 0, Max.: 255    		 0 -
    All Cylinders Misfire Count All cylinders misfire ratio
    Min.: 0, Max.: 255    		 - -
    Misfire RPM Engine RPM for first misfire range:
    Min.: 0 RPM, Max.: 6375 RPM    		 0 RPM: Misfire 0 -
    Misfire Load Engine load for first misfire range:
    Min.: 0 g/rev, Max.: 3.98 g/rev    		 0 g/rev: Misfire 0 -
    Catalyst OT MF F/C Catalyst overheat misfire prevention fuel cut availability:
    Not Avl or Avail
    • Avail: Catalyst overheat misfire prevention fuel cut available
    • Not Avl: Catalyst overheat misfire prevention fuel cut not available
    		 Service data
    Cat OT MF F/C History Catalyst overheat misfire prevention fuel cut history:
    ON or OFF    		 ON: Fuel cut operation history exists Service data
    Cat OT MF F/C Cylinder #1 Display of fuel cut operation in No. 1 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #2 Display of fuel cut operation in No. 2 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #3 Display of fuel cut operation in No. 3 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #4 Display of fuel cut operation in No. 4 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #5 Display of fuel cut operation in No. 5 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #6 Display of fuel cut operation in No. 6 (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    A/C Magnetic Clutch Relay A/C Magnetic clutch relay status:
    ON or OFF    		 - Active Test support data
    Electric Fan Motor Electric fan motor:
    ON or OFF    		 ON: Electric fan motor operating -
    Idle Fuel Cut Prohibit Idle fuel cut prohibit:
    ON or OFF    		 - -
    Idle Fuel Cut Fuel cut idle:
    ON or OFF    		 ON: Fuel cut is operating Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2500 RPM
    FC TAU Fuel cut TAU (fuel cut during very light load):
    ON or OFF    		 ON: Fuel cut is operating Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
    Electrical Load Signal 1 Electrical load signal:
    ON or OFF    		 - -
    Electrical Load Signal 2 Electrical load signal:
    ON or OFF    		 - -
    Electrical Load Signal 3 Electrical load signal:
    ON or OFF    		 - -
    Electrical Load Signal 4 Electrical load signal:
    ON or OFF    		 - -
    Key Unlock Signal Key unlock signal:
    ON or OFF    		 - -
    Model Code Model code - Identifying model code:
    GRS19#
    Engine Type Engine type - Identifying engine type:
    2GRFSE
    Cylinder Number Cylinder number:
    Min.: 0, Max.: 255    		 - Identifying cylinder number:
    6
    Destination Destination - Identifying destination:
    A (America)
    Model Year Model year:
    Min.: 1900, Max.: 2155    		 - Identifying model year:
    2010
    System Identification System identification - Identifying engine system:
    Gasoline (gasoline engine)
    Engine Speed of Cyl #1 Engine speed for cylinder 1:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Engine Speed of Cyl #2 Engine speed for cylinder 2:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Engine Speed of Cyl #3 Engine speed for cylinder 3:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Engine Speed of Cyl #4 Engine speed for cylinder 4:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Engine Speed of Cyl #5 Engine speed for cylinder 5:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Engine Speed of Cyl #6 Engine speed for cylinder 6:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Av Engine Speed of All Cyl Engine speed for all cylinders:
    Min.: 0 RPM, Max.: 51199 RPM    		 - Output only when Check the Cylinder Compression is performed using Active Test
    51199 RPM: Active Test not performed
    Received MIL from ECT Received MIL from TCM:
    ON or OFF    		 MIL illuminate instruction ON signal from TCM: ON -
    Shift Position Sig from ECT Received shift position signal from TCM:
    1st, 2nd, 3rd, 4th, 5th, or 6th    		 Actual shift position -
    A/T Oil Temp from ECT Received ATF temperature sensor value from TCM:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    • After stall test: Approximately 80°C (176°F)
    • Equal to ambient temperature when cold soak
    		 If the value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is open or shorted
    SPD (NO) Output shaft speed:
    Min.: 0 RPM, Max.: 12750 RPM    		 0 RPM: Vehicle stopped -
    SPD (NT) Input shaft speed:
    Min.: 0 RPM, Max.: 12750 RPM
    • Lock-up is ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    • Lock-up is OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    		 -
    ECT Lock Up Lock up:
    ON or OFF    		 ON: Lock up operating -

    HINT: 

    • *1: Excluding throttle valve opening percentage due to idle speed control.
    • *2: Data List values are only displayed when performing the following Active Test: Control the VVT System (Bank 1, 2), Control the VVT Linear (Bank 1, 2) and Control the Exhaust VVT Linear (Bank 1, 2). For other Active Tests, the Data List value will be 0.
  2. ACTIVE TEST 

    HINT: 

    Performing the Active Test enables components including the relays, VSV (Vacuum Switching Valve) and actuators, to be operated without removing any parts. The Active Test can be performed with the Techstream. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time.

    • The Data List can be displayed during the Active Test.
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Active Test.
    5. Perform the Active Test by referring to the table below.
    Tester Display Test Part Control Range Diagnostic Note
    Control the Injection Volume C hange injection volume Between -12.5 and 24.8%
    • All injectors tested at the same time
    • Perform test at less than 3000 RPM
    • Injection volume can be changed in 0.1 or 0.2% graduations within control range
    Control the Injection Volume for A/F Sensor Change injection volume Lower by 12.5% or increase by 25%
    • Perform test at less than 3000 RPM
    • Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
    • To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1, B2S1 and O2S B1S2, B2S2
    Activate the Fuel Pump Speed Control Fuel pump speed control ON (low speed) / OFF (high speed) Test possible when following conditions are met:
    • Engine switch on (IG)
    • Engine is stopped
    Activate the VSV for Evap Control Activate purge VSV control ON/OFF -
    Control the A/C Magnet Clutch Control the A/C compressor ON/OFF -
    Control the Fuel Pump / Speed Activate fuel pump (C/OPN Relay) ON/OFF -
    Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
    • ON: TC and TE1 connected
    • OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
    Prohibit the Catalyst OT Misfire Prevent F/C Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire ON: Fuel cut is prohibited Confirm that the vehicle is stopped and engine speed is 3000 RPM or less.
    Control the Electric Cooling Fan Control Electric Cooling Fan ON/OFF Test possible when following conditions are met:
    • Engine switch on (IG)
    • Engine is stopped
    Activate the Starter Relay Activate the starter relay ON/OFF Confirm that the engine is stopped
    Activate the ACC Cut Relay Activate the ACC cut relay ON/OFF Confirm that the engine is stopped
    Control the ETCS Open Slow Speed Control the ETCS (throttle motor) opening slow speed Open/Close Test is possible when the following conditions are met:
    • Engine switch on (IG)
    • Engine does not start
    • Accelerator pedal fully depressed (APP: 58 degrees or more)
    Control the ETCS Close Slow Speed Control the ETCS (throttle motor) closing slow speed Open/Close Same as above
    Control the ETCS Open Fast Speed Control the ETCS (throttle motor) opening fast speed Open/Close Same as above
    Control the ETCS Close Fast Speed Control the ETCS (throttle motor) closing fast speed Open/Close Same as above
    Control the VVT Linear (Bank 1) Control VVT (bank 1) -128 to 127%
    This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    • Engine stalls or idles roughly when VVT actuator operated by 100%.
    • Test possible during engine idle.
    Control the VVT System (Bank 1) Turn on and off OCV
    (Oil Control Valve)    		 ON/OFF
    • Engine stalls or idles roughly when OCV turned ON
    • Normal engine running or idling when OCV OFF
    Control the VVT Linear (Bank 2) Control VVT (bank 2) -128 to 127%
    This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    • Engine stalls or idles roughly when VVT actuator operated by 100%.
    • Test possible during engine idle.
    Control the VVT System (Bank 2) Turn on and off OCV
    (Oil Control Valve)    		 ON/OFF
    • Engine stalls or idles roughly when OCV turned ON
    • Normal engine running or idling when OCV OFF
    Control the VVT Exhaust Linear (Bank 1) Control VVT (bank 1) -128 to 127%
    This valve added to present OCV control duty
    100%: Maximum retard
    -100%: Maximum advance
    • Engine stalls or idles roughly when VVT actuator operated by 100%.
    • Test possible during engine idle.
    Control the VVT Exhaust Linear (Bank 2) Control VVT (bank 2) -128 and 127%
    This valve added to present OCV control duty
    100%: Maximum retard
    -100%: Maximum advance
    • Engine stalls or idles roughly when VVT actuator operated by 100%.
    • Test possible during engine idle.
    Control the Injection Timing #1 Control injection timing #1 Between -16 to 15.87°CA Test possible during vehicle stopping and engine idling.
    Control the Injection Timing #2 Control injection timing #2 Between -16 to 15.87°CA
    Control the Injection Timing #3 Control injection timing #3 Between -16 to 15.87°CA
    Control the Injection Timing #4 Control injection timing #4 Between -16 to 15.87°CA
    Control the Injection Timing #5 Control injection timing #5 Between -16 to 15.87°CA
    Control the Injection Timing #6 Control injection timing #6 Between -16 to 15.87°CA
    Activate the Vacuum Pump Leak detection pump ON/OFF -
    Activate the VSV for Vent Valve Vent valve ON/OFF -
    Control the Target Fuel Pressure Control the target fuel pressure Between -12.5 and 24.8% Test possible during vehicle stopping and engine idling.
    Control the Injection Way Perform 3 patterns in order to operate fuel injection Either/Port/Direct Test can be performed when both of following conditions are met:
    • Vehicle stopped and engine idling
    • When the Data List Injection Switching Status is normal
    D-4S (A/F Control) Perform 3 pattern in order to operate air fuel ratio control Either/Port/Direct
    • Vehicle stopped and engine idling
    • When the Data List Injection Switching Status is normal
    D-4S (Injection Volume) Perform 3 pattern in order to operate injection volume Either/Port/Direct
    • Vehicle stopped and engine idling
    • When the Data List Injection Switching Status is normal
    D-4S (Fuel Cut) Perform 3 pattern in order to operate fuel cut Either/Port/Direct
    • Vehicle stopped and engine idling
    • When the Data List Injection Switching Status is normal
    Control the Cylinder #1 Fuel Cut Cylinder #1 injector fuel cut ON/OFF Test possible during vehicle stopping and engine idling.*1
    Control the Cylinder #2 Fuel Cut Cylinder #2 injector fuel cut ON/OFF
    Control the Cylinder #3 Fuel Cut Cylinder #3 injector fuel cut ON/OFF
    Control the Cylinder #4 Fuel Cut Cylinder #4 injector fuel cut ON/OFF
    Control the Cylinder #5 Fuel Cut Cylinder #5 injector fuel cut ON/OFF
    Control the Cylinder #6 Fuel Cut Cylinder #6 injector fuel cut ON/OFF
    Control the All Cylinders Fuel Cut All cylinders fuel cut ON/OFF Test possible while vehicle stopped and engine idling.*1
    Check the Cylinder Compression*2 Check the cylinder compression pressure ON/OFF Fuel injection and ignition stopped in all cylinders
    NOTE:

    *1: If the display of the Catalyst OT MF F/C item of the Data List is Not Avl, perform this Active Test with the vehicle stopped and the engine idling. If the display of the Catalyst OT MF F/C item of the Data List is Avail, perform this Active Test as described below.

    1. Stop the engine and turn the engine switch on (IG) to turn Control the Cylinder #1 Fuel Cut (to #6 Fuel Cut) on.
    2. Start the engine.

    HINT: 

    *2: While the Active Test item Check the Cylinder Compression is being performed, the fuel and ignition of all cylinders is cut. At this time, the ECM measures the speed of each cylinder while the engine is being cranked.

    If one cylinder's speed is higher than the others, that cylinder's compression pressure can be concluded to be lower than the others.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the Techstream on.
    6. Select the following menu items: Powertrain / Engine / Active Test / Check the Cylinder Compression.

      HINT: 

      If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine / Data List / Engine speed of Cyl #1 to #6 and Av Engine Speed of All Cyl.

    7. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT: 

      After performing the above procedure, the Check the Cylinder Compression Active Test will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine speed measurement will enter standby mode.

    8. Fully open the throttle.
    9. Crank the engine for about 10 seconds.
    10. Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the Techstream.

      HINT: 

      At first, the Techstream display will show each cylinder's engine speed measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine speed measurement will change to the actual engine speed.

      NOTE:
      • The Check the Cylinder Compression Active Test is turned ON, it will automatically turn off 255 seconds after the Active Test is turned on.
      • When the Check the Cylinder Compression Active Test is OFF and the engine is cranked, the engine will start.
      • If the Check the Cylinder Compression Active Test needs to be performed again after each cylinder's engine speed measurement has been performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.
      • Use a fully-charged battery.
  3. SYSTEM CHECK 

    HINT: 

    Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check.
    5. Perform the System Check by referring to the table below.
    Tester Display Test Part Control Range Diagnostic Note
    Evaporative System Check
    (Automatic Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
    • If no DTCs in Pending after performing this test, system functioning normally
    • Refer to EVAP system. Refer to EVAP System .
    Evaporative System Check
    (Manual Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
    • Used to detect malfunctioning parts
    • Refer to EVAP system. Refer to EVAP System .
scientia non olet · About LEMON Manuals