DTC P050B: Cold Start Ignition Timing Performance: Procedure

CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)

Connect Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Select the following the menu items: Powertrain / Engine / Trouble Codes.

Read the DTCs.

Result

Display (DTC Output)	Proceed to
P050B	A
P050B and other DTCs	B

HINT:

If any DTCs other than P050B are output, troubleshoot those DTCs first.

B → See step 16

A: Go to next step

READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.
1. Connect Techstream to the DLC3.
2. Start the engine.
3. Turn the tester on.
4. Select the following menu items: Powertrain / Engine / Data List / Short FT #1 and Long FT #1.
5. Read the values displayed on the tester at engine idles.
6. Add together the Short FT #1 and Long FT #1 values to obtain the total FUEL TRIM.
  OK
  
  Total of Short FT #1 and Long FT #1 values is between -20% and 20%.
OK → See step 12

NG: Go to next step

PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

Connect Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

Tester Operation	Specified Condition
OCV OFF	Normal engine speed
OCV ON	Engine idles roughly or stalls (soon after OCV switched from OFF to ON)

NG → See step 8

OK: Go to next step

CHECK PCV HOSE CONNECTIONS
OK

PCV hose is connected correctly and is not damaged.

NG → See step 9

OK: Go to next step
CHECK INTAKE SYSTEM
1. Check the intake system for vacuum leakage.
  OK
  
  No leakage from intake system.
NG → See step 10

OK: Go to next step
CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.
  OK
  
  Air cleaner filter element is not excessively contaminated with dirt or oil.
NG → See step 11

OK: Go to next step
REPLACE MASS AIR FLOW METER
1. Replace mass air flow meter . Refer to REMOVAL .
NEXT → See step 15
CHECK AND REPAIR VVT SENSOR
NEXT → See step 15
REPAIR OR REPLACE PCV HOSE
NEXT → See step 15
REPAIR OR REPLACE INTAKE SYSTEM
NEXT → See step 15
REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
NEXT → See step 15
CHECK THROTTLE VALVE
1. Check for deposits around the throttle valve and throttle valve condition.
  OK
  
  No deposits around throttle valve and throttle valve moves smoothly.
NG → See step 14

OK: Go to next step
REPLACE ECM
1. Replace ECM . Refer to REMOVAL .
NEXT → See step 15
REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
NEXT → See step 15
CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
NOTE:
In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).
1. Connect Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Clear the DTCs . Refer to DTC CHECK / CLEAR .
5. Turn the engine switch off and wait for 30 seconds.
6. Turn the engine switch on (IG) and turn the Techstream on.
7. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
8. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
9. Input the DTC: P050B
10. Check the DTC judgment result.
  OK
  
  DTC judgment result is NORMAL.
NEXT → END
GO TO DTC CHART. Refer to DIAGNOSTIC TROUBLE CODE CHART