Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch: Procedure

1. Check that the remote up and down function using the power window regulator master switch assembly operates the front passenger door window. Refer to OPERATION CHECK .

   OK

   Front passenger door remote up and down function operates normally.

NG → See step   2 

OK → See step   8 

1. Disconnect the power window regulator switch assembly connector.
   Fig 1: Identifying L17 Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to Power Window Regulator Switch Assembly)

2. Measure the resistance and voltage according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L17-20 (GND) - Body ground	Always	Below 1 Ω

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   L17-8 (B) - L17-20 (GND)	Always	11 to 14 V
   L17-10 (B) - L17-20 (GND)	Always	11 to 14 V

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Turn the engine switch on (IG).
2. Measure the voltage according to the value(s) in the table below.
   Fig 2: Identifying M17 Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   TEXT IN ILLUSTRATION
   
   

   *1	Component with harness connected (Power Window Regulator Master Switch Assembly)

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   M17-16 (PWS) - Body ground	Window lock switch off	11 to 14 V
   M17-16 (PWS) - Body ground	Window lock switch on	Below 1 V

NG → See step   9 

OK: Go to next step 

1. Disconnect the power window regulator master switch assembly connector.
   Fig 3: Identifying M17 And L17 Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to Power Window Regulator Master Switch Assembly)
   *2	Front view of wire harness connector (to Power Window Regulator Switch Assembly)

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M17-16 (PWS) - L17-16 (PCT)	Always	Below 1 Ω
   M17-16 (PWS) - Body ground	Always	10 kΩ or higher
   L17-16 (PCT) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Remove the power window regulator motor assembly (for front passenger side). Refer to REMOVAL .
   Fig 4: Identifying Power Window Regulator Motor Assembly (For Front Passenger Side) Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   TEXT IN ILLUSTRATION
   
   

   *1	Component without harness connected (Power Window Regulator Motor Assembly (for Front Passenger Side))
   *2	Clockwise
   *3	Counterclockwise

2. Check power window regulator motor operation:
   1. Apply battery voltage to connector terminals 1 and 2.
      NOTE:

      Do not apply battery voltage to any terminals except terminals 1 and 2.

   2. Check that the motor gear rotates smoothly as follows.

      OK

      Measurement Condition	Specified Condition
      Battery positive (+) → 1 (D) Battery negative (-) → 2 (U)	Motor gear rotates clockwise
      Battery positive (+) → 2 (U) Battery negative (-) → 1 (D)	Motor gear rotates counterclockwise

3. Check PTC operation:
   NOTE:

   This check must be performed with the power window regulator and door glass installed on the vehicle.

   1. Install the power window regulator motor assembly (for front passenger side). Refer to INSTALLATION .
   2. Reconnect the power window regulator switch assembly connector.
   3. Initialize the power window regulator switch assembly. Refer to INITIALIZATION .
   4. Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.
      Fig 5: Identifying L15 Connector Terminals

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION
      
      

      *1	Component with harness connected (Power Window Regulator Motor Assembly (for Front Passenger Side))

      NOTE:

      Match the arrow mark of the probe with the direction of the current flow.

   5. Fully close the door glass by pulling up the power window regulator switch assembly. Wait for approximately 60 seconds.
   6. Continue to pull up the power window regulator switch assembly and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (current shut-off inspection).

      Standard

      4 to 90 seconds

   7. Wait for 60 seconds after the previous step, and then push down the power window regulator switch assembly.

      OK

      The front passenger door window goes down.

NG → See step   7 

OK: Go to next step 

1. Disconnect the power window regulator switch assembly connector.
2. Disconnect the power window regulator motor assembly (for front passenger side) connector.
   Fig 6: Identifying L17 And L15 Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   TEXT IN ILLUSTRATION
   
   

   *1	Front view of wire harness connector (to Power Window Regulator Switch Assembly)
   *2	Front view of wire harness connector (to Power Window Regulator Motor Assembly (for Front Passenger Side))

3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   L17-1 (UP) - L15-2 (U)	Always	Below 1 Ω
   L17-11 (DN) - L15-1 (D)	Always	Below 1 Ω
   L17-1 (UP) - Body ground	Always	10 kΩ or higher
   L17-11 (DN) - Body ground	Always	10 kΩ or higher
   L15-2 (U) - Body ground	Always	10 kΩ or higher
   L15-1 (D) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   8