LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2010 >> LS 460 AWD >> Repair and Diagnosis (Single Page) >> Engine Performance >> System >> Engine Control System (Diagnostics - Introduction) >> SFI System >> Data List / Active Test >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.

    Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine / Data List / All Data /
    7. Check the values by referring to the table below.
    Tester Display Measurement Item/Range Normal Condition*1 Diagnostic Note
    Vehicle Speed Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h    		 Actual vehicle speed Speed indicated on speedometer
    Engine Speed Engine speed:
    Min.: 0 rpm, Max.: 16383 rpm    		 700 to 800 rpm: Idling -
    Calculate Load Calculated load by ECM:
    Min.: 0%, Max.: 100%
    • 15.0 to 35.0%: Idling
    • 15.0 to 35.0%: Running without load (2000 rpm)
    		 -
    Vehicle Load Vehicle load:
    Min.: 0%, Max.: 25700%    		 Actual vehicle load Load percentage in terms of maximum intake air flow amount
    MAF Air flow rate from MAF meter:
    Min.: 0 gm/sec., Max.: 655.35 gm/sec.    		 4.0 to 6.0 gm/sec.: Idling
    12 to 16 gm/sec.: 2000 rpm    		 If value approximately 0.0 gm/sec.:
    • Mass air flow meter power source circuit open
    • VG circuit open or short

    If value 160.0 gm/sec. or more:
    • E2G circuit open
    MAF #1 Air flow rate from MAF meter (bank 1):
    Min.: 0 g/sec., Max.: 655.35 g/sec.    		 0.8 to 4.8 g/sec.: Idling
    2.4 to 12.8 g/sec.: 2000 rpm    		 -
    MAF #2 Air flow rate from MAF meter (bank 2):
    Min.: 0 g/sec., Max.: 655.35 g/sec.    		 0.8 to 4.8 g/sec.: Idling
    2.4 to 12.8 g/sec.: 2000 rpm    		 -
    Atmosphere Pressure Atmospheric pressure:
    Min.: 0 kPa, Max.: 255 kPa    		 Equivalent to atmospheric pressure (absolute pressure) -
    Coolant Temp Engine coolant temperature:
    Min.: -40°C, Max.: 215°C    		 80 to 105°C (176 to 221°F):
    After warming up
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F): sensor circuit shorted
    Intake Air Intake air temperature:
    Min.: -40°C, Max.: 140°C    		 Equivalent to ambient air temperature
    • If value -40°C (-40°F): sensor circuit open
    • If value 140°C (284°F): sensor circuit shorted
    Intake Air #1 Intake air temperature (bank 1):
    Min.: -40°C, Max.: 215°C    		 Equivalent to ambient air temperature -
    Intake Air #2 Intake air temperature (bank 2):
    Min.: -40°C, Max.: 215°C    		 Equivalent to ambient air temperature -
    Ambient Temperature Ambient temperature:
    Min.: -40°C, Max.: 215°C    		 Equivalent to ambient air temperature: Engine switch on (IG) -
    Engine Run Time Engine run time:
    Min.: 0 s, Max.: 65535 s    		 Time after engine start -
    Initial Engine Coolant Temp Initial engine coolant temperature:
    Min.: -40°C, Max.: 119.3°C    		 Coolant temperature when engine started Service data
    Initial Intake Air Temp Initial intake air temperature:
    Min.: -40°C, Max.: 119.3°C    		 Intake air temperature when engine started Service data
    Battery Voltage Battery voltage:
    Min.: 0, Max.: 65.535 V    		 11 to 14 V: Idling -
    Accel Sens. No. 1 Volt % Accelerator Pedal Position (APP) No. 1:
    Min.: 0%, Max.: 100%    		 10 to 25%: Accelerator pedal released
    60 to 90%: Accelerator pedal fully depressed    		 -
    Accel Sens. No. 2 Volt % APP No. 2:
    Min.: 0%, Max.: 100%    		 20 to 45%: Accelerator pedal released
    80 to 100%: Accelerator pedal fully depressed    		 -
    Accel Sensor Out No. 1 APP sensor No. 1 voltage:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed    		 -
    Accel Sensor Out No. 2 APP sensor No. 2 voltage:
    Min.: 0 V, Max.: 4.98 V    		 1.2 to 2.0 V: Accelerator pedal released
    3.4 to 5.0 V: Accelerator pedal fully depressed    		 -
    Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
    Min.: 0%, Max.: 100%
    • 10 to 22%: Accelerator pedal released
    • 64 to 96%: Accelerator pedal fully depressed
    		 Calculated value based on VTA1
    Throttl Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
    Min.: 0%, Max.: 100%
    • 42 to 62%: Accelerator pedal release
    • 92 to 100%: Accelerator pedal fully depressed
    		 Calculated value based on VTA2
    System Guard System guard:
    ON or OFF    		 - -
    Throttle Idle Position Whether or not throttle position sensor detecting idle:
    ON or OFF    		 ON: Idling -
    Throttle Require Position Throttle requirement position:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 1.1 V: Idling -
    Throttle Sensor Position Absolute throttle position sensor:
    Min.: 0%, Max.: 100%
    • 0%: Accelerator pedal released
    • 50 to 80%: Accelerator pedal fully depressed
    		 Recognition value for throttle opening angle on ECM
    Throttle Position No. 1 Throttle position sensor No. 1 output voltage:
    Min.: 0 V, Max.: 4.98 V
    • 0.5 to 1.1 V: Accelerator pedal released
    • 3.2 to 4.8 V: Accelerator pedal fully depressed
    • 0.6 to 1.4 V: Fail-safe operating
    		 -
    Throttle Position No. 2 Throttle position sensor No. 2 output voltage:
    Min.: 0 V, Max.: 4.98 V
    • 2.1 to 3.1 V: Accelerator pedal released
    • 4.6 to 5.0 V: Accelerator pedal fully depressed
    • 2.1 to 3.1 V: Fail-safe operating
    		 -
    Throttle Position Command Throttle position command value:
    Min.: 0 V, Max.: 4.98 V    		 0.5 to 4.8 V ETCS service data
    Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.98 V    		 0.6 to 1.4 V ETCS service data
    Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.98 V    		 1.7 to 2.5 V ETCS service data
    Throttle Motor Current Throttle actuator current:
    Min.: 0 A, Max.: 19.9 A    		 0 to 3.0 A: Idling ETCS service data
    Throttle Motor Duty Throttle actuator:
    Min.: 0%, Max.: 100%    		 10 to 22%: Idling after engine warmed up ETCS service data
    Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
    Min.: 0%, Max.: 255%    		 0.5 to 40%: Idling ETCS service data
    Throttle Motor Duty (Close) Throttle actuator duty ratio (close):
    Min.: 0%, Max.: 255%    		 0.5 to 40%: Idling ETCS service data
    Throttle Fully Closed Learn Throttle valve fully closed
    (learned value):
    Min.: 0 V, Max.: 4.98 V    		 0.4 to 1.0 V: Accelerator pedal released -
    +BM Voltage +BM voltage:
    Min.: 0 V, Max.: 79.998 V    		 11 to 14 V: Engine switch on (IG) and system normal ETCS service data
    Actuator Power Supply Actuator power supply
    ON or OFF    		 ON: Idling -
    Throttle Position Throttle valve opening angle:
    Min.: 0 deg, Max.: 499.99 deg    		 - For use when engine stall, starting problems or rough idle is present
    ISC Flow Flow rate calculated from information from each sensor:
    Min.: 0 L/s, Max.: 79.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    ISC Position Target valve opening angle calculated from ISC:
    Min.: 0 deg, Max.: 499.99 deg    		 - For use when engine stall, starting problems or rough idle is present
    ISC Feedback Value ISC feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    ISC Learning Value ISC learned value:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    Electric Load Feedback Val Electrical load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    Air Conditioner FB Val Air conditioner load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    Low Revolution Control Status of low engine speed control:
    ON or OFF    		 - For use when engine stall, starting problems or rough idle is present
    Neutral Control N position control status for automatic transmission:
    ON or OFF    		 - For use when engine stall, starting problems or rough idle is present
    Eng Stall Control FB Flow Intake airflow feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    Deposit Loss Flow Deposit loss air flow rate:
    Min.: -40 L/s, Max.: 39.99 L/s    		 - For use when engine stall, starting problems or rough idle is present
    Fuel Press Fuel pressure (high pressure side):
    Min.: 0 kPa, Max.: 655350 kPa    		 3000 to 5000 kPa: Idling
    7000 to 9000 kPa: 2000 rpm    		 -
    Injector (Port) Port injection period of No. 1 cylinder:
    Min.: 0 μs, Max.: 65535 μs    		 0 to 2000 μs.: Idling -
    Injection Volum (Cylinder 1) Injection volume (Cylinder 1):
    Min.: 0 ml, Max.: 2.047 ml    		 0.005 to 0.015 ml: Idling Quantity of fuel injection volume for 10 times (Port and Direct)
    Fuel Pump Speed Control F/PMP relay status:
    ON or OFF    		 - Active Test support data
    Fuel Pump/Speed Status Fuel pump/status:
    ON or OFF    		 - Active Test support data
    Vacuum Pump Key-off EVAP system leak detection pump status:
    ON or OFF    		 - Active Test support data
    Fuel Pressure Target Value Target fuel pressure by the fuel pump for high pressure:
    Min.: 0 MPa, Max.: 65.535 MPa    		 3 to 5 MPa: Idling
    7 to 9 MPa: 2000 rpm (No load)    		 -
    Fuel Pump Duty (D4) Fuel pump for high pressure duty (D4) (bank 1)
    Min.: 0%, Max.: 127.5%    		 0 to 40%: Idling -
    Fuel Pump2 Duty (D4) Fuel pump for high pressure duty (D4) (bank 2)
    Min.: 0%, Max.: 127.5%    		 0 to 40%: Idling -
    HP FP Discharge Rate Fuel volume required by the fuel pump for high pressure (bank 1):
    Min.: 0 ml, Max.: 2.047 ml    		 0.04 to 0.08 ml: Idling -
    HP FP Discharge Rate 2 Fuel volume required by the fuel pump for high pressure (bank 2):
    Min.: 0 ml, Max.: 2.047 ml    		 - -
    Injection Way Injection mode:
    Port / Direct / Either    		 - -
    Injection Switching Status Prohibition of changing the D-4S injection method
    OK or NG    		 OK: Change of fuel injection method is normal Permission status of changing of fuel injection method during Active Test
    Injection Timing (D4) No. 1 cylinder injector for direct injection timing:
    Min.: -3276.8°CA, Max.: 3276.7°CA    		 310 to 330°CA: Idling -
    Injection Time (D4) Final fuel injection time of No. 1 injector for direct injection:
    Min.: 0 μs, Max.: 65535 μs    		 700 to 2000 μs: Idling -
    EVAP (Purge) VSV EVAP (Purge) VSV control duty:
    Min.: 0%, Max.: 100%    		 0 to 40%: Idling Order signal from ECM
    Evap Purge Flow Purge flow:
    Min.: 0%, Max.: 399.9%    		 0 to 8%: Idling Service data
    Purge Destiny Learn Value Learning value of purge density:
    Min.: -200, Max.: 199.993    		 -35 to 1: Idling Service data
    Vapor Pressure Pump Vapor pressure:
    Min.: 0 kPa (0 mmHg),
    Max.: 1441.77 kPa (10814.169 mmHg)    		 Approximately 100 kPa:
    Engine switch on (IG)    		 EVAP system pressure monitored by canister pressure sensor
    Vapor Pressure (Calculated) Vapor pressure (calculated):
    Min.: -720.896 kPa (-5407.167 mmHg),
    Max.: 720.874 kPa (5407.002 mmHg)    		 Approximately 100 kPa:
    Engine switch on (IG)    		 EVAP system pressure monitored by canister pressure sensor
    EVAP System Vent Value key-off EVAP system vent valve status:
    ON or OFF    		 - Active Test support data
    EVAP Purge VSV VSV status for EVAP control:
    ON or OFF    		 - Active Test support data
    Purge Cut VSV Duty Purge cut VSV duty:
    Min.: 0%, Max.: 399.9%    		 - -
    Target Air-Fuel Ratio Air-fuel ratio:
    Min.: 0, Max.: 1.99    		 0.8 to 1.2: Idling -
    AF Lambda B1 S1 Short-term fuel trim associated with bank 1 sensor 1:
    Min.: 0, Max.: 1.99
    • Value less than 1 (0.000 to 0.999) = Rich
    • Stoichiometric air-fuel ratio = 1
    • Value greater than 1 (1.001 to 1.999) = Lean
    		 -
    AF Lambda B2 S1 Short-term fuel trim associated with bank 2 sensor 1:
    Min.: 0, Max.: 1.99
    • Value less than 1 (0.000 to 0.999) = Rich
    • Stoichiometric air-fuel ratio = 1
    • Value greater than 1 (1.001 to 1.999) = Lean
    		 -
    AFS Voltage B1 S1 A/F sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 7.99 V    		 3 to 3.5 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    AFS Voltage B2 S1 A/F sensor output voltage for bank 2 sensor 1:
    Min.: 0 V, Max.: 7.99 V    		 3 to 3.5 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    AFS Current B1 S1 A/F sensor output current for bank 1 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA    		 -0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    AFS Current B2 S1 A/F sensor output current for bank 2 sensor 1:
    Min.: -128 mA, Max.: 127.99 mA    		 -0.5 to 0.5 mA: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    A/F Heater Duty #1 A/F heater duty ratio for bank 1:
    Min.: 0%, Max.: 399.9%    		 0 to 100% -
    A/F Heater Duty #2 A/F heater duty ratio for bank 2:
    Min.: 0%, Max.: 399.9%    		 0 to 100% -
    O2S B1 S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V    		 0.1 to 0.9 V:
    Driving at 44 mph (70 km/h)    		 Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    O2S B2 S2 Heated oxygen sensor output voltage for bank 2 sensor 2:
    Min.: 0 V, Max.: 1.275 V    		 0.1 to 0.9 V:
    Driving at 44 mph (70 km/h)    		 Performing Control the Injection Volume or Control the Injection Volume for A/F sensor function of Active Test enables technician to check output voltage of sensor
    O2S Impedance B1S2 Sub heated oxygen sensor impedance for bank 1 sensor 2:
    Min.: 0 ohm, Max.: 21247.67 ohm    		 5 to 15000 ohm:
    After driving approx. 10 min. in urban area    		 -
    O2S Impedance B2S2 Sub heated oxygen sensor impedance for bank 2 sensor 2:
    Min.: 0 ohm, Max.: 21247.67 ohm    		 5 to 15000 ohm:
    After driving approx. 10 min. in urban area    		 -
    O2 Heater B1S2 Heated oxygen sensor heater for bank 1 sensor 2:
    Active or Not Act    		 - -
    O2 Heater B2S2 Heated oxygen sensor heater for bank 2 sensor 2:
    Active or Not Act    		 - -
    O2 Heater Curr Val B1S2 Heated oxygen sensor current for bank 1 sensor 2:
    Min.: 0 A, Max.: 4.9 A    		 - -
    O2 Heater Curr Val B2S2 Heated oxygen sensor current for bank 2 sensor 2:
    Min.: 0 A, Max.: 4.9 A    		 - -
    Short FT #1 Short-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1 Long-term fuel trim of bank 1:
    Min.: -100%, Max.: 99.2%    		 -30 to 30% Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Total FT #1 Total fuel trim of bank 1
    Average value for fuel trim system of bank 1:
    Min.: -0.5, Max.: 0.496    		 -0.28 to 0.2: Idling -
    Short FT #2 Short-term fuel trim of bank 2:
    Min.: -100%, Max.: 99.2%    		 -20 to 20% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #2 Long-term fuel trim of bank 2:
    Min.: -100%, Max.: 99.2%    		 -30 to 30% Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Total FT #2 Total fuel trim of bank 2
    Average value for fuel trim system of bank 2:
    Min.: -0.5, Max.: 0.496    		 -0.28 to 0.2: Idling -
    Fuel System Status #1 Fuel system status (bank 1):
    OL or CL or OLDrive or OLFault or CLFault    		 CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop
    • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    • OLDrive: Open loop due to driving conditions (fuel enrichment)
    • OLFault: Open loop due to detected system fault
    • CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
    Fuel System Status #2 Fuel system status (bank 2):
    OL or CL or OLDrive or OLFault or CLFault    		 CL: Idling after warming up
    • OL (Open Loop): Has not yet satisfied conditions to go closed loop
    • CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    • OLDrive: Open loop due to driving conditions (fuel enrichment)
    • OLFault: Open loop due to detected system fault
    • CLFault: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
    IGN Advance Ignition timing advance for No. 1 cylinder:
    Min.: -64 deg., Max.: 63.5 deg.    		 BTDC 3 to 13 deg: Idling -
    Knock Feedback Value Feedback value of knocking:
    Min: -1024°CA, Max.: 1023.9°CA    		 -31.5 to 0°CA:
    Driving at 44 mph (70 km/h)    		 Service data
    Knock Correct Learn Value Correction learning value of knocking:
    Min: -1024°CA, Max.: 1023.9°CA    		 3 to 31.5°CA:
    Driving at 44 mph (70 km/h)    		 Service data
    Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #7 Individual cylinder timing advance compensation amount (No. 7):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    Idle Spark Advn Ctrl #8 Individual cylinder timing advance compensation amount (No. 8):
    Min.: 0°CA, Max.: 15.93°CA    		 - For use when engine stall, starting problems or rough idle is present
    ACIS VSV VSV status for ACIS control:
    ON or OFF    		 - Active Test support data
    ACIS Motor Duty ACIS motor duty:
    Min.: -200%, Max.: 199.99%    		 - Active Test support data
    VVT Advance Fail VSV for intake control system status:
    ON or OFF    		 ON: AICV open -
    VVT Change Angle #1* VVT intake side change angle (bank 1):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling Displacement angle during intrusive operation
    VVT Change Angle #2* VVT intake side change angle (bank 2):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 DegFR: Idling Displacement angle during intrusive operation
    VVT Ex Hold Lrn Val #1* VVT exhaust side hold duty ratio learning value (bank 1):
    Min.: 0%, Max.: 399.9%    		 0 to 80%: Idling -
    VVT Ex Chg Angle #1* VVT exhaust side change angle (bank 1)
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 to 40 DegFR: Idling Displacement angle during intrusive operation
    VVT Ex OCV Duty #1* VVT exhaust side OCV duty (bank 1)
    Min.: 0%, Max.: 399.9%    		 0 to 100%: Idling Requested duty value for intrusive operation
    VVT Ex Hold Lrn Val #2* VVT exhaust side hold duty ratio learning value (bank 2):
    Min.: 0%, Max.: 399.9%    		 0 to 80%: Idling -
    VVT Ex Chg Angle #2* VVT exhaust side change angle (bank 2)
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 0 to 40 DegFR: Idling Displacement angle during intrusive operation
    VVT Ex OCV Duty #2* VVT exhaust side OCV duty (bank 2):
    Min.: 0%, Max.: 399.9%    		 0 to 100%: Idling Requested duty value for intrusive operation
    VVT-iE Aim Angle #1* VVT intake side aim angle (bank 1):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 10 DegFR: Idling -
    VVT-iE Aim Angle #2* VVT intake side aim angle (bank 2):
    Min.: 0 DegFR, Max.: 639.9 DegFR    		 10 DegFR: Idling -
    VVT-iE Mot Direction #1 VVT motor direction (bank 1):
    Backward or Forward    		 Forward: Idling -
    VVT-iE Mot Direction #2 VVT motor direction (bank 2):
    Backward or Forward    		 Forward: Idling -
    VN Turbo Type Variable nozzle turbo type:
    Not Avl or Commo or Vacuum or CAN Com    		 Not Avl (Unused) -
    Catalyst Temp B1 S1 Catalyst temperature (bank 1 sensor 1):
    Min.: -40°C, Max.: 6513.5°C    		 - -
    Catalyst Temp B2 S1 Catalyst temperature (bank 2 sensor 1):
    Min.: -40°C, Max.: 6513.5°C    		 - -
    Catalyst Temp B1 S2 Catalyst temperature (bank 1 sensor 2):
    Min.: -40°C, Max.: 6513.5°C    		 - -
    Catalyst Temp B2 S2 Catalyst temperature (bank 2 sensor 2):
    Min.: -40°C, Max.: 6513.5°C    		 - -
    Starter Signal Starter signal:
    Open or Close    		 Open: Cranking -
    Starter Control Starter switch status:
    ON or OFF    		 ON: Cranking -
    Starter Relay Starter relay status:
    ON or OFF    		 ON: Cranking -
    ACC Relay ACC relay status:
    ON or OFF    		 ON: Cranking -
    Neutral Position SW Signal PNP switch status
    ON or OFF    		 ON: P or N position -
    Stop Light Switch Stop light switch status:
    ON or OFF    		 ON: Brake pedal depressed -
    A/C Signal A/C switch status:
    ON or OFF    		 ON: A/C ON -
    Idle Up Signal Idle up signal:
    ON or OFF    		 - -
    Closed Throttle Position SW Closed throttle position switch:
    ON or OFF
    • ON: Throttle fully closed
    • OFF: Throttle open
    		 -
    Fuel Cut Condition Fuel cut condition:
    ON or OFF    		 ON: Fuel cut operating -
    Immobiliser Communication Immobiliser communication:
    ON or OFF    		 ON: Normal -
    Check Mode Check mode:
    OFF or ON    		 ON: Check mode ON Refer toCHECK MODE PROCEDURE 
    SPD Test Result Check mode result for vehicle speed sensor:
    Compl or Incmpl    		 - -
    Misfire Test Result Check mode result for misfire monitor:
    Compl or Incmpl    		 - -
    OXS1 Test Result Check mode result for HO2 sensor (bank 1):
    Compl or Incmpl    		 - -
    OXS2 Test Result Check mode result for HO2 sensor (bank 2):
    Compl or Incmpl    		 - -
    A/F Test Results #2 Check mode result for air-fuel ratio sensor (bank 2):
    Compl or Incmpl    		 - -
    A/F Test Results #1 Check mode result for air-fuel ratio sensor (bank 1):
    Compl or Incmpl    		 - -
    Complete Parts Monitor Comprehensive component monitor:
    Not Avl or Avail    		 - -
    Fuel System Monitor Fuel system monitor:
    Not Avl or Avail    		 - -
    Misfire Monitor Misfire monitor:
    Not Avl or Avail    		 - -
    EGR/VVT Monitor EGR/VVT monitor:
    Not Avl or Avail    		 - -
    EGR/VVT Monitor EGR/VVT monitor:
    Compl or Incmpl    		 - -
    O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Not Avl or Avail    		 - -
    O2S (A/FS) Heater Monitor O2S (A/FS) heater monitor:
    Compl or Incmpl    		 - -
    O2S (A/FS) Monitor O2S (A/FS) monitor:
    Not Avl or Avail    		 - -
    O2S (A/FS) Monitor O2S (A/FS) monitor:
    Compl or Incmpl    		 - -
    A/C Monitor A/C monitor:
    Not Avl or Avail    		 - -
    A/C Monitor A/C monitor:
    Compl or Incmpl    		 - -
    2nd Air Monitor 2nd air monitor:
    Not Avl or Avail    		 - -
    2nd Air Monitor 2nd air monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor EVAP monitor:
    Not Avl or Avail    		 - -
    EVAP Monitor EVAP monitor:
    Compl or Incmpl    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Not Avl or Avail    		 - -
    Heated Catalyst Monitor Heated catalyst monitor:
    Compl or Incmpl    		 - -
    Catalyst Monitor Catalyst monitor:
    Not Avl or Avail    		 - -
    Catalyst Monitor Catalyst monitor:
    Compl or Incmpl    		 - -
    Component Monitor ENA Comprehensive component monitor:
    Unable or Enable    		 - -
    Component Monitor CMPL Comprehensive component monitor:
    Compl or Incmpl    		 - -
    Fuel System Monitor ENA Fuel system monitor:
    Unable or Enable    		 - -
    Fuel System Monitor CMPL Fuel system monitor:
    Compl or Incmpl    		 - -
    Misfire Monitor ENA Misfire monitor:
    Unable or Enable    		 - -
    Misfire Monitor CMPL Misfire monitor:
    Compl or Incmpl    		 - -
    EGR/VVT Monitor ENA EGR/VVT monitor:
    Unable or Enable    		 - -
    EGR/VVT Monitor CMPL EGR/VVT monitor:
    Compl or Incmpl    		 - -
    Heater Monitor ENA O2S (A/FS) heater monitor:
    Unable or Enable    		 - -
    Heater Monitor CMPL O2S (A/FS) heater monitor:
    Compl or Incmpl    		 - -
    O2S (A/FS) Monitor ENA O2S (A/FS) monitor:
    Unable or Enable    		 - -
    O2S (A/FS) Monitor CMPL O2S (A/FS) monitor:
    Compl or Incmpl    		 - -
    A/C Monitor ENA A/C monitor:
    Unable or Enable    		 - -
    A/C Monitor CMPL A/C monitor:
    Compl or Incmpl    		 - -
    2nd Air Monitor ENA 2nd air monitor:
    Unable or Enable    		 - -
    2nd Air Monitor CMPL 2nd air monitor:
    Compl or Incmpl    		 - -
    EVAP Monitor ENA EVAP monitor:
    Unable or Enable    		 - -
    EVAP Monitor CMPL EVAP monitor:
    Compl or Incmpl    		 - -
    Heated Cat Monitor ENA Heated catalyst monitor:
    Unable or Enable    		 - -
    Heated Cat Monitor CMPL Heated catalyst monitor:
    Compl or Incmpl    		 - -
    Catalyst Monitor ENA Catalyst monitor:
    Unable or Enable    		 - -
    Catalyst Monitor CMPL Catalyst monitor:
    Compl or Incmpl    		 - -
    TC Terminal TC terminal status:
    ON or OFF    		 - -
    # Codes (Include History) Number of emission related DTCs 0: No emission related DTC detected -
    MIL MIL status:
    ON or OFF    		 ON: MIL ON -
    MIL ON Run Distance MIL ON Run Distance:
    Min.: 0 km,
    Max.: 65535 km    		 Distance after DTC detected -
    Running Time from MIL ON Running time from MIL ON:
    Min.: 0 min.,
    Max.: 65535 min.    		 Equivalent to running time after MIL ON -
    Time after DTC Cleared Time after DTC cleared:
    Min.: 0 min.,
    Max.: 65535 min.    		 Equivalent to time after DTCs erased -
    Distance from DTC Cleared Distance after DTC cleared:
    Min.: 0 km, Max.: 65535 km    		 Equivalent to drive distance after DTCs erased -
    Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared:
    Min.: 0, Max.: 255    		 - Number of warm-up cycles after DTC cleared
    Dist Batt Cable Disconnect Distance after battery cable disconnected:
    Min.: 0 km, Max.: 65535 km    		 - -
    IG OFF Elapsed Time Time after engine switch off:
    Min.: 0 min, Max.: 655350 min    		 - -
    OBD Requirements OBD requirement OBD2 -
    Number of Emission DTC Emission related DTCs - Number of emission related DTCs
    TC and TE1 TC and CG (TE1) terminals of DLC3:
    ON or OFF    		 - Active Test support data
    Ignition Trig. Count Number of counts of misfire counter:
    Min.: 0, Max.: 65535    		 0 to 800 -
    Cylinder #1 Misfire Count Misfire count of cylinder 1:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #2 Misfire Count Misfire count of cylinder 2:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #3 Misfire Count Misfire count of cylinder 3:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #4 Misfire Count Misfire count of cylinder 4:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #5 Misfire Count Misfire count of cylinder 5:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #6 Misfire Count Misfire count of cylinder 6:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #7 Misfire Count Misfire count of cylinder 7:
    Min.: 0, Max.: 255    		 0 -
    Cylinder #8 Misfire Count Misfire count of cylinder 8:
    Min.: 0, Max.: 255    		 0 -
    All Cylinders Misfire Count All cylinders Misfire count:
    Min.: 0, Max.: 255    		 0 to 35 -
    Multi Cylinders Misfire Count Multiple Cylinder Misfire count:
    Min.: 0 Max.: 65535    		 0 to 65535 -
    Misfire RPM Average engine speed during misfire:
    Min.: 0 rpm, Max.: 6375 rpm    		 0 rpm: Misfire 0 -
    Misfire Load Average load during misfire:
    Min.: 0 g/rev, Max.: 3.98 g/rev    		 0 g/rev: Misfire 0 -
    Misfire Margin Misfire margin:
    Min.: -128%, Max.: 127%    		 -128 to 127% Misfire detecting margin
    Catalyst OT MF F/C Catalyst over temperature misfire prevention F/C:
    Not Avl or Avail    		 Avail: Cat OT MF F/C available
    Not Avl: Cat OT MF F/C not available    		 -
    Cat OT MF F/C History Catalyst over temperature misfire prevention F/C history:
    ON or OFF    		 ON: Fuel cut operation history exists -
    Cat OT MF F/C Cylinder #1 Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #2 Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #3 Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #4 Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #5 Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #6 Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #7 Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Cat OT MF F/C Cylinder #8 Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF    		 ON: Fuel cut is operating -
    Engine Speed (Starter Off) Engine speed when starter off:
    Min.: 0 rpm, Max.: 51199 rpm    		 - For use when engine stall, starting problems or rough idle is present
    Starter Count Number of times starter turned on after engine switch turned on (IG):
    Min.: 0, Max.: 255    		 - For use when engine stall, starting problems or rough idle is present
    Run Dist of Previous Trip Distance driven during previous trip:
    Min.: 0 km, Max.: 655.35 km    		 - For use when engine stall, starting problems or rough idle is present
    Engine Starting Time Time elapsed after engine started (interval between engine switch on (IG) and off):
    Min.: 0 ms, Max.: 655350 ms    		 - For use when engine stall, starting problems or rough idle is present
    Previous Trip Coolant Temp Engine coolant temperature during previous trip:
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Previous Trip Intake Temp Intake air temperature during previous trip:
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Engine Oil Temperature Engine oil temperature (estimated temperature):
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Previous Trip Eng Oil Temp Engine oil temperature during previous trip:
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Ambient Temp for A/C Ambient temperature:
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Previous Trip Ambient Temp Ambient temperature during previous trip:
    Min.: -40°C, Max.: 215°C    		 - For use when engine stall, starting problems or rough idle is present
    Engine Start Hesitation History of hesitation during engine start:
    ON or OFF    		 - -
    Low Rev for Eng Start History of low engine speed after engine start:
    ON or OFF    		 - -
    Minimum Engine Speed Minimum engine speed:
    Min.: 0 rpm, Max.: 51199 rpm    		 - For use when engine stall, starting problems or rough idle is present
    Electric Fan Motor Electric fan motors:
    ON or OFF    		 - Active Test support data
    Idle Fuel Cut Prohibit Idle fuel cut:
    ON or OFF    		 ON: Fuel cut operating Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
    Idle Fuel Cut Fuel cut idle:
    ON or OFF    		 ON: Fuel cut operating Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
    FC TAU Fuel cut TAU (Fuel cut during very light load):
    ON or OFF    		 ON: Fuel cut operating Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
    Immobiliser Fuel Cut Status of the immobiliser fuel cut:
    ON or OFF    		 - -
    Communication with ECT Status of the communication with ECT
    Comm or No Comm    		 - -
    Electrical Load Signal 1 Electrical load signal:
    ON or OFF    		 - -
    Key Unlock Signal Key unlock signal status:
    ON or OFF    		 - -
    Model Code Model code - Identifying model code:
    USF4#
    Engine Type Engine type - Identifying engine type:
    1URFSE
    Cylinder Number Cylinder number:
    Min.: 0, Max.: 255    		 - Identifying cylinder number:
    8
    Transmission Type Transmission type - Identifying transmission type:
    ECT 8th
    Destination Destination - Identifying destination:
    A (America)
    Model Year Model year:
    Min.: 1900, Max.: 2155    		 - Identifying model year:
    20##
    System Identification System identification - Identifying engine system:
    Gasoline (gasoline engine)
    Engine Speed of Cyl #1 Engine RPM for cylinder 1:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #2 Engine RPM for cylinder 2:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #3 Engine RPM for cylinder 3:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #4 Engine RPM for cylinder 4:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #5 Engine RPM for cylinder 5:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #6 Engine RPM for cylinder 6:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #7 Engine RPM for cylinder 7:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Engine Speed of Cyl #8 Engine RPM for cylinder 8:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed using Active Test
    Av Engine Speed of All Cyl Engine RPM for all cylinders:
    Min.: 0 rpm, Max.: 51199 rpm    		 - Output only when Check the Cylinder Compression is performed
    Received MIL from ECT MIL status from ECT:
    ON or OFF    		 ON: MIL ON -
    Shift Position Sig from ECT Shift position signal from ECT:
    1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th    		 - -
    A/T Oil Temp from ECT ATF temperature from ECT:
    Min.: -40°C, Max.: 215°C    		 With engine cold: Equal to ambient temperature -
    SPD (NO) Output shaft speed:
    Min.: 0 rpm, Max.: 12750 rpm    		 - -
    SPD (NT) Input shaft speed:
    Min.: 0 rpm, Max.: 12750 rpm
    • Lock up on (after warming up engine): Input turbine speed (NT) equal to engine speed
    • Lock up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    		 -
    ECT Lock Up Lock up:
    ON or OFF    		 ON: Lock up operating -
    Shift SW Status (P Range) PNP switch status:
    ON or OFF
    • Shift lever in P: ON
    • Shift lever not in P: OFF
    		 When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Pattern Switch (PWR/M) Pattern switch (PWR) status:
    ON or OFF
    • Pattern switch (PWR) pushed: ON
    • Pattern switch (PWR) not pushed: OFF
    		 -
    Shift SW Status (R Range) PNP switch status:
    ON or OFF
    • Shift lever in R: ON
    • Shift lever not in R: OFF
    		 When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (N Range) PNP switch status:
    ON or OFF
    • Shift lever in N: ON
    • Shift lever not in N: OFF
    		 When shift lever position displayed on the Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Sports Shift Up SW Sport shift up switch status:
    ON or OFF
    • ON: Shift lever held in "+" (up-shift)
    • OFF: Shift lever not held in "+" (up-shift)
    		 -
    Sports Shift Down SW Sport shift down switch status:
    ON or OFF
    • ON: Shift lever held in "-" (down-shift)
    • OFF: Shift lever not held in "-" (down-shift)
    		 -
    Sports Mode Selection SW Sport mode select switch status:
    ON or OFF
    • ON: Shift lever in M (or S), "+" or "-"
    • OFF: Shift lever not in M (or S), "+" or "-"
    		 -
    Shift SW Status (D Range) PNP switch status:
    ON or OFF
    • Shift lever in M or S: ON
    • Shift lever not in M or S: OFF
    		 -
    Snow or 2nd Start Mode Pattern switch (ECT SNOW) status:
    ON or OFF    		 Engine switch on (IG): OFF
    ↓
    Pattern switch (ECT SNOW) pushed: ON
    ↓
    Pattern switch (ECT SNOW) pushed: OFF    		 -
    Shift Control Mode Shift control mode type:
    M-mode or S-mode    		 - -

    HINT: 

    • Normal condition: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
    • *: Data List values are only displayed when performing the following Active Tests: Control the VVT-iE Linear (Bank1), Control the VVT-iE Linear (Bank2), Control the Exhaust Linear (Bank1) and Control the Exhaust Linear (Bank2). For other Active Tests, the Data List value will be 0.
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    • Data List can be displayed during Active Test.
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Active Test /
    5. According to the display on the Techstream, perform the "Active Test".
    Tester Display Test Part Control Range Diagnostic Note
    Control the Injection Volume Change injection volume -12.5 to 24.8%
    • All injectors tested at the same time
    • Perform test at less than 3000 rpm
    • Injection volume can be changed in 0.2% graduations within control range
    Control the Injection Volume for A/F Sensor Change injection volume Lower by 12.5% or increase by 25%
    • Perform test at less than 3000 rpm
    • Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
    • To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F Control System / AFS B1 S1 and O2S B1 S2
    Activate the Fuel Pump Speed Control Fuel pump speed control ON (low speed) / OFF (high speed) Test possible when following conditions met:
    • Engine switch on (IG)
    • Engine is stopped
    Activate the VSV for Intake Control Activate VSV for intake control ON/OFF -
    Activate the VSV for EVAP Control Activate purge VSV control ON/OFF -
    Control the Fuel Pump / Speed Activate fuel pump (CIRCUIT OPENING relay) ON/OFF Test possible when following conditions met:
    • Engine switch on (IG)
    • Engine is stopped
    Connect the TC and TE1 Turn on and off TC and CG (TE1) connection ON/OFF
    • ON: TC and TE1 connected
    • OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
    Prohibit the Catalyst OT Misfire Prevent F/C Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire ON: Fuel cut is prohibited Confirm that the vehicle is stopped and engine speed is 3000 rpm or less.
    Control the Electric Cooling Fan Control Electric Cooling Fan ON/OFF Test possible when following conditions met:
    • Engine switch on (IG)
    • Engine is stopped
    Active the Starter Relay Active Starter relay ON/OFF -
    Active the ACC Cut Relay Active ACC CUT relay ON/OFF Test possible when following conditions met:
    • Engine switch on (IG)
    • Engine is stopped
    Control the ETCS Open/Close Slow Speed Throttle actuator Close/Open Test possible when following conditions met:
    • Engine switch on (IG)
    • Engine is stopped
    • Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed Throttle actuator Close/Open
    Control the VVT-iE Linear (Bank1) VVT intake side (bank 1) 0 to 40 deg -
    Control the VVT-iE Linear (Bank2) VVT intake side (bank 2) 0 to 40 deg -
    Control the VVT Exhaust Linear (Bank1) Control VVT (bank 1) -128 to 127%
    This value added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    • Engine stall or rough idle when VVT actuator operated by 100%
    • Test possible while engine idling
    Control the VVT Exhaust Linear (Bank2) Control VVT (bank 2)
    Control the Injection Timing #1 Control injection timing #1 -16 CA to 15.87 CA Test possible while vehicle stopped and engine idling.
    Control the Injection Timing #2 Control injection timing #2 -16 CA to 15.87 CA
    Control the Injection Timing #3 Control injection timing #3 -16 CA to 15.87 CA
    Control the Injection Timing #4 Control injection timing #4 -16 CA to 15.87 CA
    Control the Injection Timing #5 Control injection timing #5 -16 CA to 15.87 CA
    Control the Injection Timing #6 Control injection timing #6 -16 CA to 15.87 CA
    Control the Injection Timing #7 Control injection timing #7 -16 CA to 15.87 CA
    Control the Injection Timing #8 Control injection timing #8 -16 CA to 15.87 CA
    Activate the Vacuum Pump Leak detection pump ON/OFF -
    Activate the VSV for Vent Value Vent valve ON/OFF -
    Control the Target Fuel Pressure Control the target fuel pressure -12.5 to 24.8% Test possible while vehicle stopped and engine idling.
    Control the Voltage of Alternator Request output voltage of generator regulator during forced activation 12.5 to 14.8 V Test possible while vehicle stopped and engine idling.
    Control the Injection Way Perform 3 pattern in order to operate fuel injection Either/Port/Direct
    • Vehicle stopped and engine idling
    • When the Data List's Injection Switching Status is normal
    D-4S (A/F Control) Perform 3 pattern in order to operate A/F Control Either/Port/Direct
    D-4S (Fuel Cut) Perform 3 pattern in order to operate fuel cut Either/Port/Direct
    D-4S (Injection Volume) Perform 3 pattern in order to operate injection volume Either/Port/Direct
    Control the Cylinder #1 Fuel Cut Cylinder #1 injector fuel cut ON/OFF Test possible while vehicle stopped and engine idling.*1
    Control the Cylinder #2 Fuel Cut Cylinder #2 injector fuel cut ON/OFF
    Control the Cylinder #3 Fuel Cut Cylinder #3 injector fuel cut ON/OFF
    Control the Cylinder #4 Fuel Cut Cylinder #4 injector fuel cut ON/OFF
    Control the Cylinder #5 Fuel Cut Cylinder #5 injector fuel cut ON/OFF
    Control the Cylinder #6 Fuel Cut Cylinder #6 injector fuel cut ON/OFF
    Control the Cylinder #7 Fuel Cut Cylinder #7 injector fuel cut ON/OFF
    Control the Cylinder #8 Fuel Cut Cylinder #8 injector fuel cut ON/OFF
    Control the All Cylinders Fuel Cut All cylinder fuel cut ON/OFF
    Check the Cylinder Compression*2 Check the cylinder compression pressure ON/OFF Fuel injection and ignition stop in all cylinders.
    NOTE:

    *1: If the display of the Catalyst OT MF F/C item of the Data List is Not Avl, perform this Active Test with the vehicle stopped and the engine idling. If the display of the Catalyst OT MF F/C item of the Data List is Avail, perform this Active Test as described below.

    1. Stop the engine and turn the engine switch on (IG) to turn Control the Cylinder #1 Fuel Cut (to #8 Fuel Cut) on.
    2. Start the engine.

    HINT: 

    *2: When cranking the engine, each cylinder measures the engine rpm.

    In this Active Test, the fuel and ignition of all cylinders are cut, and cranking occurs for approximately 10 seconds. Then, each cylinder measures the engine rpm. If a cylinder's engine rpm is higher than the other, that cylinder's compression pressure is compared to the other, and is determined whether it is low or not.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the engine switch on (IG) and turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

      HINT: 

      If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6, Engine Speed of Cyl #7, Engine Speed of Cyl #8 and Av Engine Speed of All Cyl.

    6. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

      HINT: 

      After performing the above procedure, the Active Test's Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine rpm measurement will enter standby mode.

    7. Crank the engine for about 10 seconds.
    8. Monitor the engine speed (Engine Speed of Cyl #1 to #8, Av Engine Speed of All Cyl) displayed on the Techstream.

      HINT: 

      At first, the Techstream's display will show each cylinder's engine rpm measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine rpm measurement will change to the actual engine rpm.

      NOTE:
      • After the Active Test's Check the Cylinder Compression is turned ON, it will automatically turn off after 255 seconds.
      • When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.
      • If the Check the Cylinder Compression test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
      • Use a fully-charged battery.
  3. SYSTEM CHECK 

    HINT: 

    Performing a System Check in the Utility menu enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Utility /
    5. Perform the System Check by referring to the table below.
    Tester Display Test Part Control Range Diagnostic Note
    Evaporative System Check
    (Automatic Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor automatically 35°C (95°F) or less
    • If no DTCs in Pending Code after performing this test, system functioning normally
    Evaporative System Check
    (Manual Mode)    		 Perform 5 steps in order to operate EVAP key-off monitor manually 35°C (95°F) or less
    • Used to detect malfunctioning parts
scientia non olet · About LEMON Manuals