LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2011 >> IS 350 Base, RWD >> Repair and Diagnosis >> Engine Mechanical >> Fuel System >> Fuel System (Service Information) >> Fuel Pressure Sensor >> Installation >> Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Fuel Pressure Sensor: Installation: Installation

  1. INSTALL FUEL PRESSURE SENSOR 
    1. Install a new gasket to the fuel pressure sensor.
    2. Using SST, install the fuel pressure sensor to the No. 1 delivery pipe.
      • SST: 09922-10240 
      • SST: 09961-01270 
      Fig 1: Installing Fuel Pressure Sensor To No. 1 Delivery Pipe Using SST
      GTY348437Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      without SST 

      Torque: 42 N.m (428 kgf cm, 31 ft. lbf) 

      with SST 

      Torque: 23 N.m (235 kgf cm, 17 ft. lbf) 

      HINT: 

      • This torque value is effective when SST is parallel to the torque wrench.
      • This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and SST with a fulcrum length of 240 mm (9.45 in.).
      • If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification. Refer to PRECAUTION .
    3. Connect the connector with the clamp.
      Fig 2: Locating Connector With Clamp
      GTY137394Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL NO. 1 FUEL PIPE  See step  9
  3. CONNECT WATER HOSE JOINT  See step  11
  4. INSTALL INTAKE MANIFOLD  See step  12
  5. INSTALL INTAKE AIR SURGE TANK  See step  3
  6. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY  . Refer to INSTALLATION - Step 1
  7. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE  . Refer to INSTALLATION - Step 2
  8. CONNECT NO. 2 VENTILATION HOSE  . Refer to INSTALLATION - Step 3
  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL  . Refer to INSTALLATION - Step 92
  10. ADD ENGINE COOLANT  . Refer to ON-VEHICLE INSPECTION - Step 5
  11. INSPECT FOR COOLANT LEAK  . Refer to ON-VEHICLE INSPECTION - Step 1
  12. INSPECT FOR FUEL LEAK  . Refer to ON-VEHICLE INSPECTION - Step 1
  13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  . Refer to INSTALLATION - Step 3
  14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH  . Refer to INSTALLATION - Step 4
  15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH  . Refer to INSTALLATION - Step 5
  16. INSTALL FRONT WIPER ARM HEAD CAP  . Refer to INSTALLATION - Step 6
  17. INSTALL ROOF DRIP SIDE FINISH MOULDING LH 
  18. INSTALL ROOF DRIP SIDE FINISH MOULDING RH 
  19. INSTALL FRONT UPPER FENDER PROTECTOR LH  . Refer to INSTALLATION - Step 9
  20. INSTALL FRONT UPPER FENDER PROTECTOR RH 

    HINT: 

    Installation procedure of the RH side is the same as that of the LH side.

  21. INSTALL V-BANK COVER SUB-ASSEMBLY  . Refer to INSTALLATION - Step 114
  22. INSTALL ENGINE ROOM SIDE COVER LH  . Refer to INSTALLATION - Step 115
  23. INSTALL ENGINE ROOM SIDE COVER RH  . Refer to INSTALLATION - Step 116
  24. INSTALL COOL AIR INTAKE DUCT SEAL  . Refer to INSTALLATION - Step 117
  25. CHECK FUNCTION OF THROTTLE WITH MOTOR BODY ASSEMBLY  . Refer to ON-VEHICLE INSPECTION - Step 1
scientia non olet · About LEMON Manuals