Data List / Active Test
- READ DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- Warm up the engine.
- Turn the power switch OFF.
- Connect the Techstream to the DLC3.
- Turn the power switch ON (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / (desired system) / Data List.
- According to the display on the Techstream, read the "Data List".MAIN BODY
Tester Display Measurement Item/Range Normal Condition Diagnostic Note ACC SW Power switch ON (ACC)/ON or OFF ON: Power switch is ON (ACC)
OFF: Power switch is OFF- IG SW Power switch ON (IG)/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- Stop Light SW Stop light switch/ON or OFF ON: Brake pedal is depressed
OFF: Brake pedal is released- Start Switch1 Start switch 1/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- Start Switch2 Start switch 2/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- Steering Unlock Switch Steering lock condition/ON or OFF ON: Steering is unlocked
OFF: Steering is locked- Shift P Signal Shift P position signal/ON or OFF ON: Shift lever in P
OFF: Shift lever not in P- Vehicle Speed Signal Vehicle speed signal/Stop or Run Stop: Vehicle is stopped
Run: Vehicle is running- IG1 Relay Monitor(Outside) D-IG1 relay outer relay monitor/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- IG2 Relay Monitor(Outside) Ignition relay No. 2 (IG2) outer relay monitor/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- IG1 Relay Monitor(Inside) D-IG1 relay inner relay monitor/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- IG2 Relay Monitor(Inside) Ignition relay No. 2 (IG2) inner relay monitor/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- ACC Relay Monitor D-ACC relay monitor/ON or OFF ON: Power switch is ON (ACC)
OFF: Power switch is OFF- Latch Circuit Latch circuit/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF, ON (ACC)- Starter Request Signal Hybrid control system start request signal/ON or OFF ON: STSW signal is ON
OFF: STSW signal is OFF- Power Supply Condition Power supply condition/All OFF, ACC ON, IG1 ON, IG2 ON, ST ON All OFF: All relays are OFF
ACC ON: D-ACC relay is ON
IG1 ON: Ignition relay No. 1(IG1) is ON
IG2 ON: Ignition relay No. 2 (IG2) is ON
ST ON: STSW signal is ON- Ready Signal Hybrid control system start request signal monitor/ON, OFF or Unknown ON: System is ON (READY)
OFF: System is OFF
Unknown: System is UnknownPower switch pressed and held with shift lever in P SMART ACCESSTester Display Measurement Item/Range Normal Condition Diagnostic Note Ignition Switch Power switch/ON or OFF ON: Power switch is ON (IG)
OFF: Power switch is OFF- Unmatched Vehicle-ID Key number/Yes or No Yes: Key number matches
No: Key number differs- No Response Response/Yes or No Yes: Response
No: No response- Unmatch Code or Form Code format/Yes or No Yes: Code format matches
No: Code format differs- Key Low Battery Key battery conditions/Yes or No Yes: Battery is depleted
No: Battery is not depleted- #Codes Number of diagnosis codes - - ID Code Difference(Resp) ID code/Yes or No Yes: ID code matches
No: ID code differs- C Code Difference Challenge code/Yes or No Yes: Challenge code matches
No: Challenge code differs- S Code Check S code certification result/NG or OK OK: S code certification result is normal
NG: S code certification result is abnormal- L Code Check L code certification result/NG or OK OK: L code certification result is normal
NG: L code certification result is abnormal- Ignition Available Area Key area where hybrid control system can be operated/All or Front All: All areas
Front: Front only-
- PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Warm up the engine.
- Turn the power switch OFF.
- Connect the Techstream to the DLC3.
- Turn the power switch ON (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / (desired system) / Active Test.
- According to the display on the Techstream, perform the "Active Test".MAIN BODY
Tester Display Test Part Control Range Diagnostic Note Indicator for Lighting Indicator illumination ON/OFF - Indicator Condition Indicator light illumination pattern Green/Red/No Sig - P Supply for Steering Lock Steering lock ECU power supply ON/OFF - SMART ACCESSTester Display Test Part Control Range Diagnostic Note Fr-Seat Inside Transmitter Indoor key antenna (for front) ON / OFF - Rr-Seat Inside Transmitter Indoor key antenna (for rear1) ON / OFF - Inside Trunk/Backdoor Transmitter Indoor key antenna (for rear2) ON / OFF - Outside Trunk/Backdoor Transmitter Electrical key antenna ON / OFF -