LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2011 >> RX 350 AWD >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Smart Access System With Push-Button Start (For Entry Function) (Diagnostics - Introduction) >> SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function) >> Customize Parameters >> Customize Parameters
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Customize Parameters

  1. CUSTOMIZING FUNCTION WITH TECHSTREAM 

    HINT: 

    The items in the table below can be customized.

    NOTE:
    • When the customer requests a change in a function, first make sure that the function can be customized.
    • Be sure to make a note of the current setting before customizing.
    • When troubleshooting a function, first make sure that the function is set to the default setting.
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Customize Setting / Smart key/Access or Warning.
    5. Select the setting by referring to the table below.
      SMART KEY/ACCESS

      Tester Display Default Content Setting
      Ignition Available Area All Function that switches the entry ignition detection area Front or All*
      Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s, or 5 s
      Back Door Opening Operation Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF
      Door Unlock Mode Driver Function that chooses the doors to be operated by entry unlock operation All or Driver
      Touch Activation Over Threshold Active The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active

      *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.

      WARNING

      Tester Display Default Content Setting
      Key Low Battery Warning ON Function that warns driver that key battery is weak ON or OFF
  2. ENTRY UNLOCK MODE SWITCHING 
    NOTE:

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

    1. Check that the power source mode is OFF and the LED on the key is not blinking. Press the lock switch and one of the other switches on the key at the same time for approximately 5 seconds while the key is in the detection area.

      Driver door unlock default setting:

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

      NOTE:

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.

      • All door unlock mode:

        When any touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart access system with push-button start to the entry unlock mode.
    3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed.
      Mode Wireless Door Lock Buzzer Assembly Combination Meter Assembly (Buzzer)
      Driver Door
      (Default)      		 Sounds 3 times Sounds once
      All Doors
      (Customized)      		 Sounds 2 times Sounds once

      HINT: 

      The procedure only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.

  3. ELECTRICAL KEY CANCEL 
    NOTE:

    Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.

    The electrical key cancel operation disables the following functions:

    • Entry Unlock/Lock
    • Entry Ignition
    • Entry Back Door Open
    • Electrical Key Lock-in Prevention
    • Warning
    • Memory Call
    1. The operation procedures are as follows:

      Precondition:

      Engine switch off, driver side door closed and unlocked.

      1. Push the unlock switch of the key once.
      2. Open the driver door within 5 seconds.
      3. Push the unlock switch of the key twice within 5 seconds.
      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.
      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

scientia non olet · About LEMON Manuals