Installation [03/2019 - ]: Procedure

INSTALL FRONT AXLE HUB SUB-ASSEMBLY
Refer to PROCEDURE - Step 1

HINT:
- If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.
- The front speed sensor is a component of the front axle hub sub-assembly. If the front speed sensor is malfunctioning, replace the front axle hub sub-assembly.
INSPECT FRONT AXLE HUB BEARING LOOSENESS
Refer to PROCEDURE - Step 4 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 4 [01/2023 - ]
INSPECT FRONT AXLE HUB RUNOUT
Refer to PROCEDURE - Step 5 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 5 [01/2023 - ]
INSTALL FRONT DISC
except Carbon Ceramic Brake: Refer to PROCEDURE - Step 1 [09/2014 - 09/2020] , or refer to PROCEDURE - Step 1 [09/2020 - 01/2023] , or refer to PROCEDURE - Step 1 [01/2023 - ]

for Carbon Ceramic Brake: Refer to PROCEDURE - Step 1 [03/2019 - 09/2020] , or refer to PROCEDURE - Step 1 [09/2020 - 01/2023] , or refer to PROCEDURE - Step 1 [01/2023 - ]
INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
Refer to PROCEDURE - Step 7 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 7 [01/2023 - ]
INSTALL FRONT SKID CONTROL SENSOR WIRE
1. for LH Side:
  1. Connect the connector to install the front skid control sensor wire LH.
  2. Install the sensor clamp to the vehicle body with the bolt.
    Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf)
    
    NOTE:
    Do not twist the front skid control sensor wire when installing it.
  3. Engage the clamp to the front No. 1 stabilizer bracket LH.
    NOTE:
    Do not twist the front skid control sensor wire when installing it.
2. for RH Side:
  1. Connect the connector to install the front skid control sensor wire RH.
  2. Install the sensor clamp to the vehicle body with the bolt.
    Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf)
    
    NOTE:
    Do not twist the front skid control sensor wire when installing it.
  3. Engage the 2 clamps to the front No. 1 stabilizer bracket RH and vehicle body.
    NOTE:
    Do not twist the front skid control sensor wire when installing it.
3. Return the front fender liner to its original position.
4. Install the 2 sensor clamps to the front shock absorber assembly and vehicle body with the 2 bolts.
  Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf)
  
  NOTE:
  Do not twist the front skid control sensor wire when installing it.
5. Install the sensor clamp to the steering knuckle with the bolt.
  Torque: 8.5 N.m (87 kgf/cm, 75 in.lbf)
  
  NOTE:
  Do not twist the front skid control sensor wire when installing it.
6. Connect the front skid control sensor wire connector to the front axle hub sub-assembly.
  NOTE:
  Do not twist the front skid control sensor wire when installing it.
7. Connect the pad wear indicator wire connector to the front skid control sensor wire.
  NOTE:
  Do not twist the pad wear indicator wire when installing it.
INSTALL FRONT FENDER LINER
1. Install the front fender liner with the screw.
INSTALL FRONT WHEEL
Refer to INSTALLATION [03/2019 - 01/2023] , or refer to INSTALLATION [01/2023 - ]
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Refer to INITIALIZATION [03/2019 - 01/2023] , or refer to INITIALIZATION [01/2023 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]
CHECK FOR SPEED SENSOR SIGNAL
Refer to TEST MODE PROCEDURE [03/2019 - 01/2023] , or refer to TEST MODE PROCEDURE [01/2023 - ]