LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2017 >> RC F >> Repair and Diagnosis >> Brakes >> Traction Control >> Brake Control System - Service Information >> Front Speed Sensor >> Removal [03/2019 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal [03/2019 - ]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [11/2017 - ]

  2. REMOVE FRONT WHEEL 

    Refer to REMOVAL [03/2019 - 01/2023] , or refer to REMOVAL [01/2023 - ]

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [03/2019 - 01/2023] , or refer to INITIALIZATION [01/2023 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

  4. SEPARATE FRONT FENDER LINER 
    GTY503167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the screw and separate the front fender liner.
  5. REMOVE FRONT SKID CONTROL SENSOR WIRE 
    1. Disconnect the pad wear indicator wire connector from the front skid control sensor wire.
      GTY499979Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Pad Wear Indicator Wire
      *2 Front Skid Control Sensor Wire
    2. Disconnect the front skid control sensor wire connector from the front axle hub sub-assembly.
    3. Remove the bolt and sensor clamp from the steering knuckle.
    4. Remove the 2 bolts and 2 sensor clamps from the front shock absorber assembly and vehicle body.
      GTY503169Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Turn back the front fender liner.
    6. for LH Side:
      1. Disengage the clamp from the front No. 1 stabilizer bracket LH.
        GTY518745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and sensor clamp from the vehicle body.
      3. Disconnect the connector to remove the front skid control sensor wire LH.
    7. for RH Side:
      1. Disengage the 2 clamps from the front No. 1 stabilizer bracket RH and vehicle body.
        GTY503171Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and sensor clamp from the vehicle body.
      3. Disconnect the connector to remove the front skid control sensor wire RH.
  6. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY 

    Refer to PROCEDURE - Step 2 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 2 [01/2023 - ]

  7. REMOVE FRONT DISC 

    except Carbon Ceramic Brake: Refer to PROCEDURE - Step 7 [09/2014 - 09/2020] , or refer to PROCEDURE - Step 6 [09/2020 - 01/2023] , or refer to PROCEDURE - Step 6 [01/2023 - ]

    for Carbon Ceramic Brake: Refer to PROCEDURE - Step 7 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 7 [01/2023 - ]

  8. REMOVE FRONT AXLE HUB SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 5 [03/2019 - 01/2023] , or refer to PROCEDURE - Step 5 [01/2023 - ]

    HINT: 

    • If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.
    • The front speed sensor is a component of the front axle hub sub-assembly. If the front speed sensor is malfunctioning, replace the front axle hub sub-assembly.
scientia non olet · About LEMON Manuals