LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2023 >> RX 350h Base >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Control System - Service Information >> Relay >> On-Vehicle Inspection [10/2022 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

On-Vehicle Inspection [10/2022 - ]: Procedure

  1. INSPECT VVT RELAY (VVT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω

      If the result is not as specified, replace the VVT relay (VVT).

  2. INSPECT NO. 1 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 1) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω

      If the result is not as specified, replace the No. 1 electronic fuel injection main relay (EFI-MAIN NO. 1).

  3. INSPECT NO. 2 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 2) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω

      If the result is not as specified, replace the No. 2 electronic fuel injection main relay (EFI-MAIN NO. 2).

  4. INSPECT NO. 3 ELECTRONIC FUEL INJECTION MAIN RELAY (EFI-MAIN NO. 3) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω

      If the result is not as specified, replace the No. 3 electronic fuel injection main relay (EFI-MAIN NO. 3).

  5. INSPECT INJECTOR RELAY (D INJ) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω

      If the result is not as specified, replace the injector relay (D INJ).

  6. INSPECT IGP RELAY (IGP NO. 1) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher kΩ
      3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω Ω
      GTY751946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the IGP relay (IGP NO. 1).

scientia non olet · About LEMON Manuals