Key Warning Chime Does Not Operate

WARNING: This page is about a different car, the 2005 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FUSE
Check if the key switch fuse [No. 19, located in the fuse block (J/B)] is blown. Refer to "WIRING DIAGRAM - CHIME - ".

Is the fuse blown?
1. YES: Replace the fuse. Be sure to repair the cause of malfunction before installing new fuse.
2. NO: GO TO 2.
CHECK WARNING CHIME OPERATION
With key removed from the ignition and the front door LH open, turn the lighting switch to 1st or 2nd position.

Does warning chime sound?
1. YES: GO TO 3.
2. NO: Go to "ALL WARNING CHIMES DO NOT OPERATE " or "KEY WARNING CHIME AND LIGHT WARNING CHIME DO NOT OPERATE (SEAT BELT WARNING CHIME DOES OPERATE) ".
CHECK BCM INPUT SIGNAL
With CONSULT-II

With "DATA MONITOR" of "BUZZER", confirm "KEY ON SW" changes when the key is inserted/removed from the ignition key cylinder.

When key is inserted in ignition key cylinder: KEY ON SW ON

When key is removed from ignition key cylinder: KEY ON SW OFF

Fig 1: CONSULT-II Display - DATA MONITOR
Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II

Check voltage between BCM harness connector M18 terminal 37 (B/R) and ground.

Fig 2: Checking Voltage Between BCM Harness Connector M18 Terminal 37 (B/R) And Ground
Courtesy of NISSAN MOTOR CO., U.S.A.

When key is inserted in ignition key cylinder: Approx. 12V

When key is removed from ignition key cylinder: Approx. 0V

OK or NG
1. OK: Replace the BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".
2. NG: GO TO 4.
CHECK KEY SWITCH
1. Turn ignition switch OFF.
2. Disconnect key switch and key lock solenoid connector (floor shift) or key switch connector (column shift).
3. Check continuity between key switch and key lock solenoid harness connector M27 (floor shift) or key switch harness connector M80 (column shift) terminals 3 and 4.
  
  Fig 3: Checking Continuity Between Key Switch And Key Lock Solenoid Harness Connector M27 Or Key Switch Harness Connector M80 Terminals 3 And 4
  Courtesy of NISSAN MOTOR CO., U.S.A.
  
  When key is inserted in ignition key cylinder: Continuity should exist
  
  When key is removed from ignition key cylinder: Continuity should not exist
OK or NG
1. OK: GO TO 5.
2. NG: Replace the key switch and key lock solenoid connector (floor shift) or key switch connector (column shift).
CHECK KEY SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M18 terminal 37 (B/R) and key switch and key lock solenoid harness connector M80 (floor shift) or key switch harness connector M27 (column shift) terminal 4 (B/R).
  Continuity should exist .
3. Check continuity between BCM harness connector M18 terminal 37 (B/R) and ground.
  Continuity should not exist .
OK or NG
1. OK: GO TO 6.
2. NG: Repair harness or connector.
CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch and key lock solenoid harness connector M80 (floor shift) or key switch harness connector M27 (column shift) terminal 3 (Y/R) and ground.

Fig 5: Checking Voltage Between Key Switch And Key Lock Solenoid Harness Connector M80 Or Key Switch Harness Connector M27 Terminal 3 And Ground
Courtesy of NISSAN MOTOR CO., U.S.A.

Battery voltage should exist .

OK or NG
1. OK: Replace the BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".
2. NG: Check harness for open or short between fuse and key switch and key lock solenoid connector (floor shift) or key switch connector (column shift).