LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2002 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 980 (Power Window System) >> Power Window System >> Door Switch Check
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Door Switch Check

WARNING: This page is about a different car, the 2003 Nissan Murano. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DOOR SWITCH INPUT SIGNAL 1 

    With CONSULT-II 

    Check door switches ("DOOR SW-DR" and "DOOR SW-AS") in "DATA MONITOR" mode with CONSULT-II.

    MONITOR ITEM CONDITION

    Monitor item Condition
    DOOR SW-DR OPEN :ON
    CLOSE :OFF
    DOOR SW-AS OPEN :ON
    CLOSE :OFF
    Fig 1: Displaying DOOR SW-DR And DOOR SW-AS In DATA MONITOR Mode
    G03358914Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    Check voltage between BCM connector and ground.

    CONNECTOR TERMINAL VOLTAGE

    Item Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
    (+) (-)
    Passenger side M34 10 (R) Ground OPEN 0
    CLOSE Battery voltage
    Driver side 14 (SB) OPEN 0
    CLOSE Battery voltage

    OK or NG

    1. OK : Door switch is OK.
    2. NG : GO TO 2.
    Fig 2: Checking Voltage Between BCM Connector And Ground
    G03358915Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK HARNESS CONTINUITY 
    1. Disconnect BCM connector.
    2. Check continuity between BCM connector M34 terminals 10, 14 and front door lock assembly connector D10, D38 terminal 4.
      1. Driver side 
      2. 14 (SB) - 4 (SB) : Continuity should exist. 
      3. Passenger side 
      4. 10 (R) - 4 (R) : Continuity should exist. 
    3. Check continuity between BCM connector M34 terminals 10, 14 and ground.
      1. 10 (R) - Ground : Continuity should not exist. 
      2. 14 (SB) - Ground : Continuity should not exist. 
    Fig 3: Checking Continuity Between BCM Connector M34 Terminals 10, 14 And Front Door Lock Assembly Connector D10, D38 Terminal 4, And Between BCM Connector M34 Terminals 10, 14 And Ground
    G03358916Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK : GO TO 3.
    2. NG : Repair or replace harness.
  3. CHECK DOOR SWITCH 

    Check continuity between front door lock assembly terminals 4 and 5.

    TERMINAL CONTINUITY

    Terminal Door switch Continuity
    4 5 OPEN No
    CLOSE Yes

    OK or NG

    1. OK : GO TO 4.
    2. NG : Replace malfunction front door lock assembly.
    Fig 4: Checking Continuity Between Front Door Lock Assembly Terminals 4 And 5
    G03358917Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK BCM OUTPUT SIGNAL 
    1. Connect BCM connector.
    2. Check voltage between BCM connector and ground.
    CONNECTOR TERMINAL VOLTAGE

    Item Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
    (+) (-)
    Passenger side M34 10 (R) Ground OPEN 0
    CLOSE Battery voltage
    Driver side 14 (SB) OPEN 0
    CLOSE Battery voltage

    OK or NG

    1. OK : Check the condition of the harness and the connector.
    2. NG : Replace BCM.
    Fig 5: Checking Voltage Between BCM Connector And Ground
    G03358918Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals