Data Monitor Mode
For DATA MONITOR mode descriptions, seeDATA MONITOR MODE DESCRIPTIONS table.
DATA MONITOR MODE DESCRIPTIONS
| Monitored Item | Description |
|---|---|
| ENG SPEED [rpm] | Indicates the engine speed computed from crankshaft position sensor (POS) and camshaft position sensor (PHASE) signal. Accuracy becomes poor if engine speed drops below the idle rpm. If the signal is interrupted while the engine is running, and abnormal value may be indicated. |
| MAS A/F SE-B1 [V] | The signal voltage of the mass air flow sensor is displayed. When the engine is stopped, a certain value is indicated. |
| COOLAN TEMP/S [°C] or [°F] | The engine coolant temperature (determined by the signal voltage of the engine coolant temperature sensor) is displayed. When the engine coolant temperature sensor is open or short-circuited, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed. |
| HO2S1 (B1) Or (B2) [V] | The signal voltage of HO2S1 is displayed. |
| HO2S2 (B1) Or (B2) [V] | The signal voltage of HO2S2 is displayed. |
| HO2S1 MNTR (B1) Or (B2) [RICH/LEAN] | Display of HO2S1 signal during air-fuel ratio feedback control: RICH - means the mixture became "rich", and control is being affected toward a leaner mixture. LEAN - means the mixture became "lean", and control is being affected toward a rich mixture. After turning ON the ignition switch, RICH is displayed until air-fuel mixture ratio feedback control begins. When the air-fuel ratio feedback is clamped, the value just before the clamping is displayed continuously. |
| HO2S2 MNTR (B1) Or (B2) [RICH/LEAN] | Display of HO2S2 signal: RICH - means the amount of oxygen after three way catalyst is relatively small. LEAN - means the amount of oxygen after three way catalyst is relatively large. When the engine is stopped, a certain value is indicated. |
| VHCL SPEED SE [km/h] or [mph] | The vehicle speed computed from the vehicle speed sensor signal sent from instrument cluster is displayed. |
| BATTERY VOLT [V] | The power supply voltage of ECM is displayed. |
| ACCEL SEN 1 Or 2 [V] | Accelerator pedal position sensor signal voltage is displayed. |
| THRTL SEN 1 Or 2 [V] | Throttle position sensor signal voltage is displayed. |
| FUEL T/TMP SE [°C] or [°F] | The fuel temperature judged from the fuel tank temperature sensor signal voltage is displayed. |
| INT/A TEMP SE [°C] or [°F] | The intake air temperature determined by the signal voltage of the intake air temperature sensor is indicated. |
| EVAP SYS PRES [V] | The signal voltage of EVAP control system pressure sensor is displayed. |
| ABSOL PRES/SE [V] | The signal voltage of the absolute pressure sensor is displayed. |
| FUEL LEVEL SE [V] | The signal voltage of the fuel level sensor is displayed. |
| START SIGNAL [ON/OFF] | Indicates [ON/OFF] condition from the starter signal. After starting the engine, [OFF] is displayed regardless of the starter signal. |
| CLSD THL POS [ON/OFF] | Indicates idle position [ON/OFF] computed by ECM according to the throttle position sensor signal. |
| AIR COND SIG [ON/OFF] | Indicates [ON/OFF] condition of the air conditioner switch as determined by the air conditioner signal. |
| P/N POSI SW [ON/OFF] | Indicates [ON/OFF] condition from the park/neutral position (PNP) switch signal. |
| PW/ST SIGNAL [ON/OFF] | [ON/OFF] condition of the power steering oil pressure switch determined by the power steering oil pressure signal is indicated. |
| LOAD SIGNAL [ON/OFF] | Indicates [ON/OFF] condition from the electrical load signal and/or lighting switch. ON - rear defogger is operating and/or lighting switch is on. OFF - rear defogger is not operating and lighting switch is not on. |
| IGNITION SW [ON/OFF] | Indicates [ON/OFF] condition from ignition switch. |
| BRAKE SW [ON/OFF] | Indicates [ON/OFF] condition from stop lamp switch signal. |
| INJ PULSE-B1 Or B2 [msec] | Indicates the actual fuel injection pulse width compensated by ECM according to the input signals. When the engine is stopped, a certain computed value is indicated. |
| B/FUEL SCHDL [msec] | "Base fuel schedule" indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction. |
| IGN TIMING [BTDC] | Indicates the ignition timing computed by ECM according to the input signals. When the engine is stopped, a certain value is indicated. |
| PURG VOL C/V [%] | Indicates the EVAP canister purge volume control solenoid valve control value computed by the ECM according to the input signals. The opening becomes larger as the value increases |
| A/F ALPHA-B1 Or B2 [%] | The mean value of the air-fuel ratio feedback correction factor per cycle is indicated. When the engine is stopped, a certain value is indicated. This data also includes the data for the air-fuel ratio learning control. |
| AIR COND RLY [ON/OFF] | The air conditioner relay control condition (determined by ECM according to the input signal) is indicated. |
| FUEL PUMP RLY [ON/OFF] | Indicates the fuel pump relay control condition determined by ECM according to the input signals. |
| VENT CONT/V [ON/OFF] | The control condition of the EVAP canister vent control valve (determined by ECM according to the input signal) is indicated. ON - Closed; OFF - Open |
| HO2S1 HTR (B1) Or (B2) [ON/OFF] | Indicates [ON/OFF] condition of heated oxygen sensor 1 heater (front) determined by ECM according to the input signals. |
| HO2S2 HTR (B1) Or (B2) [ON/OFF] | Indicates [ON/OFF] condition of heated oxygen sensor 2 heater (rear) determined by ECM according to the input signals. |
| VC/V BYPASS/V [ON/OFF] | The control condition of the vacuum cut valve bypass valve (determined by ECM according to the input signal) is indicated. ON - Open; OFF - Closed |
| CAL/LD VALUE [%] | "Calculated load value" indicates the value of the current airflow divided by peak airflow. |
| MASS AIRFLOW [g m/s] | Indicates the mass airflow computed by ECM according to the signal voltage of the mass airflow sensor. |
| INT/V TIM (B1) Or (B2) [°CA] | Indicates [°CA] of intake camshaft advanced angle. |
| INT/V SOL (B1) Or (B2) [%] | The control condition of intake valve timing control solenoid valve (determined by ECM according to input signals) is indicated. ON - intake valve timing control is operating. OFF - intake valve timing control is not operating. |
| TRVL AFTER MIL [km] or [Mile] | Distance traveled while MIL is activated |
| VIAS S/V [ON/OFF] | The control condition of VIAS control solenoid valve (determined by ECM according to input signals) is indicated. ON - VIAS control solenoid valve is operating. OFF - VIAS control solenoid valve is not operating. |
| IDL A/V LEAN | Display the condition of idle air volume learning. YET - Idle air volume learning has not been performed yet. CMPLT - Idle air volume learning has already been performed successfully. INCMP - Idle air volume learning has not been performed successfully. |
| ENGINE MOUNT [IDLE/TRVL] | The control condition of the electronic controlled engine mount (computed by ECM according to input signals) is indicated. IDLE - Idle condition; TRVL - Driving condition. |
| COOLING FAN [HI/LOW/OFF] | Indicates the control condition of the cooling fan (determined by ECM according to input signal). HI - High speed operation; LOW - Low speed operation; OFF - Stop. |
| THRTL RELAY [ON/OFF] | Indicates throttle control motor relay control condition determined by ECM according to input signals. |
| AC PRESS SEN [V] | The signal voltage from the refrigerant pressure sensor is displayed. |
| BRAKE SW 1 [ON/OFF] | Indicates [ON/OFF] condition from ASCD brake switch signal, and ASCD clutch switch signal (M/T models) or park/neutral position relay signal (A/T models). |
| BRAKE SW 2 [ON/OFF] | Indicates [ON/OFF] condition of stop lamp switch signal. |
| MAIN SW [ON/OFF] | Indicates [ON/OFF] condition from CRUISE switch signal. |
| CANCEL SW [ON/OFF] | Indicates [ON/OFF] condition from CANCEL switch signal. |
| RESUME/ACC SW [ON/OFF] | Indicates [ON/OFF] condition from ACCEL/RES switch signal. |
| SET SW [ON/OFF] | Indicates [ON/OFF] condition from COAST/SET switch signal. |
| VHCL SPEED SE [km/h] or [mph] | The present vehicle speed computed from the vehicle speed signal sent from combination meter is displayed. |
| SET VHCL SPD [km/h] or [mph] | The preset vehicle speed is displayed. |
| VHCL SPD CUT [NON/CUT] | Indicates the vehicle cruise condition. NON - Vehicle speed is maintained at the ASCD set speed; CUT - Vehicle speed decreased to excessively low compared with the ASCD set speed, and ASCD operation is cut off. |
| LO SPEED CUT [NON/CUT] | Indicates the vehicle cruise condition. NON - Vehicle speed is maintained at the ASCD set speed; CUT - Vehicle speed decreased to excessively low compared with the ASCD set speed, and ASCD operation is cut off. |
| AT OD MONITOR [ON/OFF] | Indicates [ON/OFF] condition of A/T OD according to the input signal from the TCM. |
| AT OD CANCEL [ON/OFF] | Indicates [ON/OFF] condition of A/T OD cancel signal sent from the TCM. |
| CRUISE LAMP [ON/OFF] | Indicates [ON/OFF] condition of CRUISE lamp determined by the ECM according to the input signals. |
| SET LAMP [ON/OFF] | Indicates [ON/OFF] condition of SET lamp determined by the ECM according to the input signals. |
| DUTY-HI, DUTY-LOW, PLS WIDTH-HI & PLS WIDTH-LOW | Voltage, frequency [msec, Hz or %], duty cycle or pulse width measured by the probe. Pulse width measured by the pulse probe. Only "#" is displayed if the item is unable to be measured. Figures with "#"s are temporary ones. They are the same figures as an actual piece of data which was just previously measured. |
| CAN COMM [OK/NG]; CAN CIRC 1, 2 Or 3 [OK/UNKWN] | Indicates communication condition of CAN communication line. |