Operation Procedure
WARNING: This page is about a different car, the 2006 Nissan Xterra. However, it is still accessible from the selected car via links, so may be relevant.
- After turning ignition switch OFF, connect CONSULT-II and the CONSULT-II CONVERTER to the data link connector.CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
- Touch "START (NISSAN BASED VHCL)", "ABS", "DATA MONITOR" in order on the CONSULT-II screen. If "ABS" is not indicated, go to
"CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT
".CAUTION: When "START (NISSAN BASED VHCL)" is touched immediately after starting the engine or turning on the ignition switch, "ABS" might not be displayed in the SELECT SYSTEM screen. In this case, repeat the operation from step 2.
- Return to the SELECT MONITOR ITEM screen, and touch "ECU INPUT SIGNALS", "MAIN SIGNALS", or "SELECTION FROM MENU". Refer to the following information.
- When "START" is touched, the data monitor screen is displayed.
Display Item List
DISPLAY ITEM LIST
| Item (Unit) |
Data monitor item selection | Remarks | ||
|---|---|---|---|---|
| ECU INPUT SIGNALS | MAIN SIGNALS | SELECTION FROM MENU | ||
| GEAR | X | X | X | Gear position judged by PNP switch signal is displayed. |
| FR RH SENSOR (km/h, MPH) |
X | X | X | Wheel speed calculated by front RH wheel sensor signal is displayed. |
| FR LH SENSOR (km/h, MPH) |
X | X | X | Wheel speed calculated by front LH wheel sensor signal is displayed. |
| RR RH SENSOR (km/h, MPH) |
X | X | X | Wheel speed calculated by rear RH wheel sensor signal is displayed. |
| RR LH SENSOR (km/h, MPH) |
X | X | X | Wheel speed calculated by rear LH wheel sensor signal is displayed. |
| BATTERY VOLT (V) |
X | X | X | Voltage supplied to ABS actuator and electric unit (control unit) is displayed. |
| N POSI SIG | - | - | X | Shift position judged by PNP switch signal. |
| P POSI SIG | - | - | X | Shift position judged by PNP switch signal. |
| ACCEL POS SIG (%) |
X | - | X | Throttle valve open/close status judged by CAN communication signal is displayed. |
| ENGINE SPEED (rpm) |
X | X | X | Engine speed judged by CAN communication signal is displayed. |
| STRANGLE SIG (deg) |
X | - | X | Steering angle detected by steering angle sensor is displayed. |
| YAW RATE SEN (d/s) |
X | X | X | Yaw rate detected by yaw rate sensor is displayed. |
| DECELG-SEN (d/s) |
X | X | X | Longitudinal acceleration detected by decel G-sensor is displayed. |
| SIDE G-SENSOR (m/s2 ) |
X | - | X | Transverse acceleration detected by side G-sensor is displayed. |
| STOP LAMP SW (ON/OFF) |
X | X | X | Stop lamp switch (ON/OFF) status is displayed. |
| OFF SW (ON/OFF) |
X | X | X | VDC OFF switch (ON/OFF) status is displayed. |
| HDCSW (ON/OFF) |
- | - | X | HDC switch (ON/OFF) status is displayed. |
| ABS WARN LAMP (ON/OFF) |
- | X | X | ABS warning lamp (ON/OFF) status is displayed. |
| SLIP LAMP (ON/OFF) |
- | X | X | SLIP indicator lamp (ON/OFF) status is displayed. |
| FR LH IN SOL (ON/OFF) |
- | X | X | Front LH IN ABS solenoid (ON/OFF) status is displayed. |
| FR LH OUT SOL (ON/OFF) |
- | X | X | Front LH OUT ABS solenoid (ON/OFF) status is displayed. |
| RR RH IN SOL (ON/OFF) |
- | X | X | Rear RH IN ABS solenoid (ON/OFF) status is displayed. |
| RR RH OUT SOL (ON/OFF) |
- | X | X | Rear RH OUT ABS solenoid (ON/OFF) status is displayed. |
| FR RH IN SOL (ON/OFF) |
- | X | X | Front RH IN ABS solenoid (ON/OFF) status is displayed. |
| FR RH OUT SOL (ON/OFF) |
- | X | X | Front RH OUT ABS solenoid (ON/OFF) status is displayed. |
| RR LH IN SOL (ON/OFF) |
- | X | X | Rear LH IN ABS solenoid (ON/OFF) status is displayed. |
| RR LH OUT SOL (ON/OFF) |
- | X | X | Rear LH OUT ABS solenoid (ON/OFF) status is displayed. |
| OFF LAMP (ON/OFF) |
- | X | X | OFF Lamp (ON/OFF) status is displayed. |
| MOTOR RELAY (ON/OFF) |
- | X | X | ABS motor relay signal (ON/OFF) status is displayed. |
| ACTUATOR RLY (ON/OFF) |
- | X | X | ABS actuator relay signal (ON/OFF) status is displayed. |
| CV1 (ON/OFF) |
- | - | X | Front side switch-over solenoid valve (cut valve) (ON/OFF) status is displayed. |
| CV2 (ON/OFF) |
- | - | X | Rear side switch-over solenoid valve (cut-valve) (ON/OFF) status is displayed. |
| SV1 (ON/OFF) |
- | - | X | Front side switch-over solenoid valve (suction valve) (ON/OFF) status is displayed. |
| SV2 (ON/OFF) |
- | - | X | Rear side switch-over solenoid valve (suction valve) (ON/OFF) status is displayed. |
| VDC FAIL SIG (ON/OFF) |
- | - | X | VDC fail signal (ON/OFF) status is displayed. |
| TCS FAIL SIG (ON/OFF) |
- | - | X | TCS fail signal (ON/OFF) status is displayed. |
| ABS FAIL SIG (ON/OFF) |
- | - | X | ABS fail signal (ON/OFF) status is displayed. |
| EBD FAIL SIG (ON/OFF) |
- | - | X | EBD fail signal (ON/OFF) status is displayed. |
| FLUID LEV SW (ON/OFF) |
X | - | X | Brake fluid level switch (ON/OFF) status is displayed. |
| EBD SIGNAL (ON/OFF) |
- | - | X | EBD operation (ON/OFF) status is displayed. |
| ABS SIGNAL (ON/OFF) |
- | - | X | ABS operation (ON/OFF) status is displayed. |
| TCS SIGNAL (ON/OFF) |
- | - | X | TCS operation (ON/OFF) status is displayed. |
| VDC SIGNAL (ON/OFF) |
- | - | X | VDC operation (ON/OFF) status is displayed. |
| HDC SIGNAL (ON/OFF) |
- | - | X | HDC operation (ON/OFF) status is displayed. |
| HSA SIGNAL (ON/OFF) |
- | - | X | HSA operation (ON/OFF) status is displayed. |
| STP LAMP ON RLY | - | - | X | Stop lamp relay signal status is displayed |
| EBD WARN LAMP | - | - | X | Brake warning lamp (ON/OFF) status is displayed. |
| SLCT LVR POSI | X | X | X | Shift position judged by PNP switch signal. |
| R POSI SIG | - | - | X | Shift position judged by PNP switch signal. |
| 2WD/4WD | - | - | X | It recognizes on software whether it is 2WD and whether it is in 4WD state. |
| PRESS SENSOR | X | - | X | Brake pressure detected by pressure sensor is displayed. |
| PRESS SEN 2 | - | - | X | Brake pressure detected by pressure sensor is displayed. |
| CRANKING SIG | - | - | X | The input state of the key SW START position signal is displayed. |
| X: Applicable | ||||
| -: Not applicable | ||||