Monitored Item

WARNING: This page is about a different car, the 2005 Infiniti FX45 and 2005 Infiniti FX35. However, it is still accessible from the selected car via links, so may be relevant.

MONITORED ITEM DESCRIPTION

x: applicable
Monitored Item [unit]	ECU INPUT SIGNALS	MAIN SIGNALS	SELECTION FROM MENU	Description
VHCL SPEED SE [km/h] or [mph]	X	X	X	Indicates vehicle speed calculated from ICC unit through CAN communication [ABS actuator and electric unit (control unit) transmits wheel speed sensor signal through CAN communication].
SET VHCL SPD [km/h] or [mph]		X	X	Indicates set vehicle speed memorized in ICC unit.
THRTL OPENING [%]	X	X	X	Indicates throttle angle read from ICC unit through CAN communication (ECM transmits throttle angle through CAN communication).
ENGINE RPM [rpm]	X		X	Indicates engine speed read from ICC unit through CAN communication (ECM transmits engine speed through CAN communication).
DISTANCE ADJ [SHOR/MID/LONG]	X	X	X	Indicates set distance memorized in ICC unit.
WIPER SW [OFF/LOW/HIGH]	X		X	Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request signal through CAN communication).
MAIN SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
SET/COAST SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
CANCEL SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
RESUME/ACC SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from ICC steering switch signal (ECM transmits ICC steering switch signal through CAN communication).
CRUISE OPE [ON/OFF]		X	X	Indicates whether controlling or not (ON means "controlling").
BRAKE SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from ICC brake switch signal.
STOP LAMP SW [ON/OFF]	X	X	X	Indicates [ON/OFF] status as judged from stop lamp switch signal.
RELEASE SW NO [ON/OFF]	X		X	Indicates [ON/OFF] status as judged from release switch signal. ON when brake is depressed. OFF when brake is not depressed.
RELEASE SW NC [ON/OFF]	X		X	Indicates [ON/OFF] status as judged from release switch signal. ON when brake is not depressed. OFF when brake is depressed.
IDLE SW [ON/OFF]	X		X	Indicates [ON/OFF] status of idle switch read from ICC unit through CAN communication (ECM transmits ON/OFF status through CAN communication).
GEAR [1,2,3,4,5]	X		X	Indicates AT gear position read from ICC unit through CAN communication (TCM transmits gear position through CAN communication).
BUZZER O/P [ON/OFF]			X	Indicates [ON/OFF] status of ICC warning chime output.
ICC WARNING			X	NOTE: This item is displayed, but cannot monitor.
VHCL SPD AT [km/h] or [mph]			X	Indicates vehicle speed calculated from AT vehicle speed sensor read from ICC unit through CAN communication (TCM transmits AT vehicle speed sensor signal through CAN communication).
PRESS SENS [bar]	X	X	X	Indicates brake fluid pressure value calculated from signal voltage of pressure sensor.
PRESS SENS 2	X		X	NOTE: This item is displayed, but cannot monitor.
D RANGE SW [ON/OFF]	X		X	Indicates [ON/OFF] status of "D" position read from ICC unit through CAN communication (TCM transmits ON/OFF condition of "D" position through CAN communication).
AT OD OFF [ON/OFF]			X	Indicates [ON/OFF] status of OD cancel output under control.
NP RANGE SW [ON/OFF]	X		X	Indicates PNP switch signal read from ICC unit through CAN communication (TCM transmits PNP switch signal through CAN communication).
DISTANCE			X	NOTE: This item is displayed, but cannot monitor.
RELATIVE SPD			X	NOTE: This item is displayed, but cannot monitor.
STP LMP DRIVE [ON/OFF]		X	X	Indicates [ON/OFF] status of brake hold relay drive output.