Reference Value From Consult-II
WARNING: This page is about a different car, the 2005 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.
REFERENCE VALUE FROM CONSULT-II CHART
| Monitor item | Display content | Data monitor | Note: Error inspection checklist | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Condition | Reference value in normal operation | |||||||||
| N POSI SIG | PNP switch signal ON/OFF condition | A/T shift position = N position | ON | , "CAN Communication System Inspection " | ||||||
| A/T shift position = other than N positions | OFF | |||||||||
| P POSI SIG | PNP switch signal ON/OFF condition | A/T shift position P position | ON | , "CAN Communication System Inspection " | ||||||
| A/T shift position = other than P positions | OFF | |||||||||
| GEAR | A/T gear position | 1st gear | 1 | - | ||||||
| 2nd gear | 2 | |||||||||
| 3rd gear | 3 | |||||||||
| 4th gear | 4 | |||||||||
| 5th gear | 5 | |||||||||
| FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h (MPH)] | , "WHEEL SENSOR SYSTEM INSPECTION " | ||||||
| Vehicle running ((1)) | Almost in accordance with speedometer display (within +/- 10%) | |||||||||
| ACCEL POS SIG | Open/close condition of throttle valve (linked with accelerator pedal). | Accelerator pedal not depressed (ignition switch is ON) | 0% | , "CAN Communication System Inspection " | ||||||
| Depress accelerator pedal (ignition switch is ON) | 0 to 100% | |||||||||
| ENGINE SPEED | With engine running | With engine stopped | 0 rpm | , "ENGINE SYSTEM INSPECTION " | ||||||
| Engine running | Almost in accordance with tachometer display | |||||||||
| BATTERY VOLT | Battery voltage supplied to ABS actuator and electric unit (control unit) | Ignition switch ON | 10 to 16V | , "ABS/ABLS Control Unit Power and Ground Systems Inspection " | ||||||
| STOP LAMP SW | Stop lamp switch operation | Brake pedal depressed | ON | , "STOP LAMP SWITCH SYSTEM INSPECTION " | ||||||
| Brake pedal not depressed | OFF | |||||||||
| ABS WARN LAMP | ABS warning lamp ON condition ((2)) | ABS warning lamp ON | ON | - | ||||||
| ABS warning lamp OFF | OFF | |||||||||
| MOTOR RELAY | Operation status of motor and motor relay | Ignition switch ON or running (ABS not activated) | OFF | , "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " | ||||||
| Ignition switch ON or engine running (ABS activated) | ON | |||||||||
| ACTUATOR RLY | Actuator relay operation status | Vehicle stopped (Ignition switch ON) | OFF | , "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " | ||||||
| Vehicle stopped (Engine running) | ON | |||||||||
| SLIP LAMP | SLIP indicator lamp status ((3)) | When SLIP indicator lamp is ON | ON | , "CAN Communication System Inspection " | ||||||
| When SLIP indicator lamp is OFF | OFF | |||||||||
| FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL |
Solenoid valve operation | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode). | ON | , "SOLENOID AND CHANGE-OVER VALVE SYSTEM INSPECTION " | ||||||
| When actuator (solenoid) is not active and actuator relay is active (ignition switch ON). | OFF | |||||||||
| CV1 CV2 SV1 SV2 |
Switch-over valve status | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (when in fail-safe mode). | ON | |||||||
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON). | OFF | |||||||||
| PRESS SENSOR | Brake fluid pressure detected by pressure sensor | Do not step on the Brake pedal (When ignition switch is ON) | Approx. 0 bar | - | ||||||
| Step on the Brake pedal (When ignition switch is ON) | -40 to 300 bar | |||||||||
| FLUID LEV SW | ON/OFF status of brake fluid level switch | When brake fluid level switch ON | ON | DI-30, "WARNING LAMPS" | ||||||
| When brake fluid level switch OFF | OFF | |||||||||
| ABS SIGNAL EBD SIGNAL |
Signal status | ABS active EBD active |
ON | ABS system EBD system |
||||||
| ABS not active EBD not active |
OFF | |||||||||
| ABS FAIL SIG EBD FAIL SIG |
Fail signal status | ABS fail EBD fail |
ON | ABS system EBD system |
||||||
| ABS normal EBD normal |
OFF | |||||||||
ON: For approximately 2 seconds after ignition switch is turned ON, or when a malfunction is detected. OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and ABLS function is not activated. ON: For approximately 2 seconds after ignition switch is turned ON, or when ABLS function is activated while driving. OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and ABLS function is not activated. |
||||||||||