Reference Value From Consult-II

WARNING: This page is about a different car, the 2006 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.

REFERENCE VALUE FROM CONSULT-II

Monitor item	Display content	Data monitor		NOTE: Error inspection checklist
Monitor item	Display content	Condition	Reference value in normal operation	NOTE: Error inspection checklist
N POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = N position	ON	"CAN COMMUNICATION SYSTEM INSPECTION "
N POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = other than N positions	OFF	"CAN COMMUNICATION SYSTEM INSPECTION "
P POSI SIG	PNP switch signal ON/OFF condition	A/T shift position P position	ON	"CAN COMMUNICATION SYSTEM INSPECTION "
P POSI SIG	PNP switch signal ON/OFF condition	A/T shift position = other than P positions	OFF	"CAN COMMUNICATION SYSTEM INSPECTION "
GEAR	A/T gear position	1st gear	1	-
		2nd gear	2
		3rd gear	3
		4th gear	4
		5th gear	5
FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR	Wheel speed	Vehicle stopped	0 [km/h (MPH)]	"WHEEL SENSOR SYSTEM INSPECTION "
FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR	Wheel speed	Vehicle running (Note 1)	Almost in accordance with speedometer display (within +/-10%)	"WHEEL SENSOR SYSTEM INSPECTION "
ACCEL POS SIG	Open/close condition of throttle valve (linked with accelerator pedal).	Accelerator pedal not depressed (ignition switch is ON)	0%	"CAN COMMUNICATION SYSTEM INSPECTION "
ACCEL POS SIG		Depress accelerator pedal (ignition switch is ON)	0 to 100%	"CAN COMMUNICATION SYSTEM INSPECTION "
ENGINE SPEED	With engine running	With engine stopped	0 rpm	"ENGINE SYSTEM INSPECTION "
ENGINE SPEED	With engine running	Engine running	Almost in accordance with tachometer display	"ENGINE SYSTEM INSPECTION "
BATTERY VOLT	Battery voltage supplied to ABS actuator and electric unit (control unit)	Ignition switch ON	10 to 16V	"ABS/ABLS CONTROL UNIT POWER AND GROUND SYSTEMS INSPECTION "
STOP LAMP SW	Stop lamp switch operation	Brake pedal depressed	ON	"STOP LAMP SWITCH SYSTEM INSPECTION "
STOP LAMP SW	Stop lamp switch operation	Brake pedal not depressed	OFF	"STOP LAMP SWITCH SYSTEM INSPECTION "
ABS WARN LAMP	ABS warning lamp ON condition (Note 2)	ABS warning lamp ON	ON	-
ABS WARN LAMP	ABS warning lamp ON condition (Note 2)	ABS warning lamp OFF	OFF	-
MOTOR RELAY	Operation status of motor and motor relay	Ignition switch ON or running (ABS not activated)	OFF	"ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
MOTOR RELAY	Operation status of motor and motor relay	Ignition switch ON or engine running (ABS activated)	ON	"ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
ACTUATOR RLY	Actuator relay operation status	Vehicle stopped (Ignition switch ON)	OFF	"ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
ACTUATOR RLY	Actuator relay operation status	Vehicle stopped (Engine running)	ON	"ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION "
SLIP LAMP	SLIP indicator lamp status (Note 3)	When SLIP indicator lamp is ON	ON	"CAN COMMUNICATION SYSTEM INSPECTION "
SLIP LAMP	SLIP indicator lamp status (Note 3)	When SLIP indicator lamp is OFF	OFF	"CAN COMMUNICATION SYSTEM INSPECTION "
FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL	Solenoid valve operation	Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode).	ON	"SOLENOID AND CHANGE-OVER VALVE SYSTEM INSPECTION "
	Solenoid valve operation	When actuator (solenoid) is not active and actuator relay is active (ignition switch ON).	OFF
CV1 CV2 SV1 SV2	Switch-over valve status	When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (when in fail-safe mode).	ON
CV1 CV2 SV1 SV2	Switch-over valve status	When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON).	OFF
PRESS SENSOR	Brake fluid pressure detected by pressure sensor	Do not step on the Brake pedal (When ignition switch is ON)	Approx. 0 bar	-
PRESS SENSOR	Brake fluid pressure detected by pressure sensor	Step on the Brake pedal (When ignition switch is ON)	-40 to 300 bar	-
FLUID LEV SW	ON/OFF status of brake fluid level switch	When brake fluid level switch ON	ON	"WARNING LAMPS "
FLUID LEV SW	ON/OFF status of brake fluid level switch	When brake fluid level switch OFF	OFF	"WARNING LAMPS "
ABS SIGNAL EBD SIGNAL	Signal status	ABS active EBD active	ON	ABS system EBD system
ABS SIGNAL EBD SIGNAL	Signal status	ABS not active EBD not active	OFF	ABS system EBD system
ABS FAIL SIG EBD FAIL SIG	Fail signal status	ABS fail EBD fail	ON	ABS system EBD system
ABS FAIL SIG EBD FAIL SIG	Fail signal status	ABS normal EBD normal	OFF	ABS system EBD system
Note 1: Confirm tire pressure is normal. Note 2: ON/OFF timing of ABS warning lamp ON: For approximately 2 seconds after ignition switch is turned ON, or when a malfunction is detected. OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and ABLS/ABS function is not activated. Note 3: SLIP indicator lamp ON/OFF timing ON: For approximately 2 seconds after ignition switch is turned ON, or when ABLS function is activated while driving. OFF: Approximately 2 seconds after ignition switch is turned ON (when system is in normal operation) and ABLS function is not activated.